ramips: DIR-610-A1 Support

http://patchwork.openwrt.org/patch/3933/

Signed-off-by: Flavio Silveira <[email protected]>

SVN-Revision: 37785

target/linux/ramips/base-files/etc/diag.sh

@@ -27,7 +27,7 @@ get_status_led() {
 	d105)
 		status_led="d105:red:power"
 		;;
-	dir-300-b1 | dir-600-b1 | dir-600-b2 | dir-615-h1 | dir-615-d | dir-620-a1| dir-620-d1)
+	dir-300-b1 | dir-600-b1 | dir-600-b2 | dir-610-a1 | dir-615-h1 | dir-615-d | dir-620-a1| dir-620-d1)
 		status_led="d-link:green:status"
 		;;
 	dir-645)

target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom

@@ -68,6 +68,7 @@ case "$FIRMWARE" in
 	br6524n | \
 	carambola | \
 	d105 | \
+	dir-610-a1 | \
 	dir-615-h1 | \
 	dir-620-a1 | \
 	dir-620-d1 | \

target/linux/ramips/base-files/etc/uci-defaults/01_leds

@@ -77,6 +77,7 @@ case $board in
 	dir-810l)
 		ucidef_set_led_default "power" "POWER" "dlink:green:power" "1"
 		;;
+	dir-610-a1 |\
 	esr-9753)
 		set_wifi_led "rt2800pci-phy0::radio"
 		;;

target/linux/ramips/base-files/etc/uci-defaults/02_network

@@ -77,6 +77,7 @@ ramips_setup_interfaces()
 		ucidef_add_switch_vlan "switch0" "2" "0 6t"
 		;;
 
+	dir-610-a1 | \
 	dir-615-h1 | \
 	mzk-w300nh2)
 		ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
@@ -205,7 +206,8 @@ ramips_setup_macs()
 
 	dir-300-b1 |\
 	dir-300-b2 |\
-	dir-600-b1)
+	dir-600-b1 |\
+	dir-610-a1)
 		lan_mac=$(mtd_get_mac_binary devdata 16388)
 		wan_mac=$(macaddr_add "$lan_mac" 1)
 		;;

target/linux/ramips/base-files/lib/preinit/06_set_iface_mac

@@ -39,7 +39,8 @@ preinit_set_mac_address() {
 	asl26555 |\
 	dir-300-b1 |\
 	dir-300-b2 |\
-	dir-600-b1)
+	dir-600-b1 |\
+	dir-610-a1)
                 mac=$(mtd_get_mac_binary devdata 16388)
                 ifconfig eth0 hw ether $mac 2>/dev/null
                 ;;

target/linux/ramips/base-files/lib/ramips.sh

@@ -73,6 +73,9 @@ ramips_board_detect() {
 	*"DIR-600 B2")
 		name="dir-600-b2"
 		;;
+	*"DIR-610 A1")
+		name="dir-610-a1"
+		;;
 	*"DIR-620 A1")
 		name="dir-620-a1"
 		;;

target/linux/ramips/dts/DIR-610-A1.dts

@@ -0,0 +1,100 @@
+/dts-v1/;
+
+/include/ "rt5350.dtsi"
+
+/ {
+	compatible = "DIR-610-A1", "ralink,rt5350-soc";
+	model = "D-Link DIR-610 A1";
+	
+	palmbus@10000000 {
+		sysc@0 {
+			ralink,pinmux = "i2c", "spi", "jtag", "uartlite", "mdio", "sdram", "rgmii";
+			ralink,uartmux = "gpio";
+			ralink,wdtmux = <1>;
+		};
+
+		gpio0: gpio@600 {
+			status = "okay";
+		};
+
+		spi@b00 {
+			status = "okay";
+			m25p80@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "f25l32pa", "m25p80";
+				reg = <0 0>;
+				linux,modalias = "m25p80";
+				spi-max-frequency = <10000000>;
+
+				partition@0 {
+					label = "u-boot";
+					reg = <0x0 0x30000>;
+					read-only;
+				};
+
+				partition@30000 {
+					label = "devdata";
+					reg = <0x30000 0x10000>;
+		            		read-only;
+				};
+
+				factory: partition@40000 {
+					label = "factory";
+					reg = <0x40000 0x10000>;
+					read-only;
+				};
+
+				partition@50000 {
+					label = "firmware";
+					reg = <0x50000 0x3b0000>;
+				};
+			};
+		};
+	};
+
+	ethernet@10100000 {
+		status = "okay";
+	};
+
+	esw@10110000 {
+		status = "okay";
+		ralink,portmap = <0x1f>;
+		ralink,led-polarity = <0>;
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		status {
+			label = "d-link:green:status";
+			gpios = <&gpio0 9 1>;
+		};
+	        wps {
+			label = "d-link:green:wps";
+			gpios = <&gpio0 13 1>;
+		};
+        };
+
+        gpio-keys-polled {
+		gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <20>;
+			reset {
+				label = "reset";
+				gpios = <&gpio0 10 1>;
+				linux,code = <0x198>;
+			};
+			wps {
+				label = "wps";
+				gpios = <&gpio0 0 1>;
+				linux,code = <0x211>;
+			};
+		};
+	};
+
+	wmac@10180000 {
+		status = "okay";
+    	};
+};

target/linux/ramips/image/Makefile

@@ -280,6 +280,8 @@ endif
 # RT305X Profiles
 #
 
+Image/Build/Profile/DIR610A1=$(call BuildFirmware/Seama/$(1),$(1),dir-610-a1,DIR-610-A1,wrgn59_dlob.hans_dir610,ralink_default_fw_size_4M)
+
 edimax_3g6200n_mtd_size=3735552
 Image/Build/Profile/3G6200N=$(call BuildFirmware/Edimax/$(1),$(1),3g-6200n,3G-6200N,$(edimax_3g6200n_mtd_size),CSYS,3G62,0x50000,0xc0000)
 
@@ -505,6 +507,7 @@ define Image/Build/Profile/Default
 	$(call Image/Build/Profile/DIR-300-B1,$(1))
 	$(call Image/Build/Profile/DIR-600-B1,$(1))
 	$(call Image/Build/Profile/DIR-600-B2,$(1))
+	$(call Image/Build/Profile/DIR610A1,$(1))
 	$(call Image/Build/Profile/DIR-615-D,$(1))
 	$(call Image/Build/Profile/DIR-620-A1,$(1))
 	$(call Image/Build/Profile/DIR-620-D1,$(1))

target/linux/ramips/rt305x/profiles/dlink.mk

@@ -18,3 +18,13 @@ endef
 
 $(eval $(call Profile,DIR615H1))
 
+define Profile/DIR610A1
+	NAME:=Dlink DIR-610 A1
+	PACKAGES:=kmod-ledtrig-netdev kmod-ledtrig-timer
+endef
+
+define Profile/DIR610A1/Description
+	Package set for Dlink DIR610 A1 board
+endef
+
+$(eval $(call Profile,DIR610A1))