ath79: add support for OCEDO Ursus

SOC:   Qualcomm Atheros QCA9558
RAM:   128MB
FLASH: 16MB (Macronix MX25L12845EMI-10G)
WLAN1: QCA9558 2.4GHz 802.11bgn 3SS
WLAN2: QCA9880 5GHz 802.11ac 3SS
LED:   Power, LAN1, LAN2, 2.4GHz, 5GHz
Serial:Next to SPI Flash,
       Pinout is 3V3 - GND - TX - RX (Square Pin is 3V3)
       The Serial setting is 115200-8-N-1

INSTALLATION:

1. Serve an OpenWrt ramdisk image named "ursus.bin".
   Set your IP-address to 192.168.100.8/24.
2. Connect to the serial. Power up the device and interrupt
   the boot process.
3. Set the correct bootcmd with
   > setenv bootcmd run bootcmd_1
   > saveenv
4. Run
   > tftpboot 0x81000000 ursus.bin
   > bootm 0x81000000
5. Wait for OpenWrt to boot up.
6. Transfer OpenWrt sysupdate image and flash via sysupgrade.

Signed-off-by: Markus Scheck <[email protected]>
Tested-by: David Bauer <[email protected]>
[whitespace fix, renamed LED labels and SoC type fix]
Signed-off-by: Petr Štetiar <[email protected]>

target/linux/ath79/base-files/etc/board.d/02_network

@@ -79,7 +79,8 @@ ath79_setup_interfaces()
 		ucidef_set_interfaces_lan_wan "eth1" "eth0"
 		;;
 	devolo,dvl1200e|\
-	devolo,dvl1750e)
+	devolo,dvl1750e|\
+	ocedo,ursus)
 		ucidef_set_interface_lan "eth0 eth1"
 		;;
 	dlink,dir-825-b1)

target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata

@@ -119,7 +119,8 @@ case "$FIRMWARE" in
 		ath10kcal_extract "art" 20480 2116
 		ath10kcal_patch_mac_crc $(mtd_get_mac_text board_data 2176)
 		;;
-	ocedo,koala)
+	ocedo,koala|\
+	ocedo,ursus)
 		ath10kcal_extract "art" 20480 2116
 		ath10kcal_patch_mac $(mtd_get_mac_binary art 12)
 		;;

target/linux/ath79/dts/qca9558_ocedo_ursus.dts

@@ -0,0 +1,147 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca9557.dtsi"
+
+/ {
+	compatible = "ocedo,ursus", "qca,qca9558";
+	model = "OCEDO Ursus";
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		wifi2 {
+			label = "ursus:green:wlan2g";
+			gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy1tpt";
+		};
+
+		wifi5 {
+			label = "ursus:green:wlan5g";
+			gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0tpt";
+		};
+
+	};
+
+};
+
+&pcie1 {
+	status = "okay";
+};
+
+&uart {
+	status = "okay";
+};
+
+&pll {
+	clocks = <&extosc>;
+};
+
+&spi {
+	status = "okay";
+	num-cs = <1>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <25000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			uboot: partition@0 {
+				label = "u-boot";
+				reg = <0x000000 0x040000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "u-boot-env";
+				reg = <0x040000 0x010000>;
+			};
+
+			partition@50000 {
+				compatible = "denx,uimage";
+				label = "firmware";
+				reg = <0x050000 0x740000>;
+			};
+
+			partition@790000 {
+				label = "vendor";
+				reg = <0x790000 0x740000>;
+				read-only;
+			};
+
+			partition@ed0000 {
+				label = "data";
+				reg = <0xed0000 0x110000>;
+				read-only;
+			};
+
+			partition@fe0000 {
+				label = "id";
+				reg = <0xfe0000 0x010000>;
+				read-only;
+			};
+
+			art: partition@ff0000 {
+				label = "art";
+				reg = <0xff0000 0x010000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&wmac {
+	status = "okay";
+
+	mtd-cal-data = <&art 0x1000>;
+	mtd-mac-address = <&art 0x06>;
+};
+
+&mdio0 {
+	status = "okay";
+
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+
+	phy2: ethernet-phy@2 {
+		reg = <2>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	mtd-mac-address = <&art 0x00>;
+	phy-handle = <&phy1>;
+	pll-data = <0xa6000000 0x80000101 0x80001313>;
+
+	gmac_config: gmac-config {
+		device = <&gmac>;
+
+		rxdv-delay = <3>;
+		rxd-delay = <3>;
+		txen-delay = <0>;
+		txd-delay = <0>;
+		rgmii-enabled = <1>;
+	};
+};
+
+&eth1 {
+	status = "okay";
+	mtd-mac-address = <&art 0x12>;
+	phy-handle = <&phy2>;
+	pll-data = <0x3000101 0x101 0x1313>;
+};

target/linux/ath79/image/generic.mk

@@ -501,6 +501,15 @@ define Device/ocedo_raccoon
 endef
 TARGET_DEVICES += ocedo_raccoon
 
+define Device/ocedo_ursus
+  ATH_SOC := qca9558
+  DEVICE_TITLE := OCEDO Ursus
+  DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
+  IMAGE_SIZE := 7424k
+  IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
+endef
+TARGET_DEVICES += ocedo_ursus
+
 define Device/openmesh_om5p-ac-v2
   ATH_SOC := qca9558
   DEVICE_TITLE := OpenMesh OM5P-AC v2