|
|
@@ -1,260 +0,0 @@
|
|
|
-From a1490c1e8a12a8286c6a34c3d277a519066fc51e Mon Sep 17 00:00:00 2001
|
|
|
-From: Linus Walleij <[email protected]>
|
|
|
-Date: Sat, 7 Oct 2023 14:32:40 +0200
|
|
|
-Subject: [PATCH] ARM: dts: ixp4xx: Add USRobotics USR8200 device tree
|
|
|
-
|
|
|
-This is a USRobotics NAS/Firewall/router that has been supported
|
|
|
-by OpenWrt in the past. It had dedicated users so let's get it
|
|
|
-properly supported.
|
|
|
-
|
|
|
-Some debugging and fixing was provided by Howard Harte.
|
|
|
-
|
|
|
-Link: https://lore.kernel.org/r/[email protected]
|
|
|
-Signed-off-by: Linus Walleij <[email protected]>
|
|
|
----
|
|
|
- arch/arm/boot/dts/intel/ixp/Makefile | 3 +-
|
|
|
- .../ixp/intel-ixp42x-usrobotics-usr8200.dts | 229 ++++++++++++++++++
|
|
|
- 2 files changed, 231 insertions(+), 1 deletion(-)
|
|
|
- create mode 100644 arch/arm/boot/dts/intel/ixp/intel-ixp42x-usrobotics-usr8200.dts
|
|
|
-
|
|
|
---- a/arch/arm/boot/dts/intel/ixp/Makefile
|
|
|
-+++ b/arch/arm/boot/dts/intel/ixp/Makefile
|
|
|
-@@ -16,4 +16,5 @@ dtb-$(CONFIG_ARCH_IXP4XX) += \
|
|
|
- intel-ixp43x-gateworks-gw2358.dtb \
|
|
|
- intel-ixp42x-netgear-wg302v1.dtb \
|
|
|
- intel-ixp42x-arcom-vulcan.dtb \
|
|
|
-- intel-ixp42x-gateway-7001.dtb
|
|
|
-+ intel-ixp42x-gateway-7001.dtb \
|
|
|
-+ intel-ixp42x-usrobotics-usr8200.dtb
|
|
|
---- /dev/null
|
|
|
-+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-usrobotics-usr8200.dts
|
|
|
-@@ -0,0 +1,229 @@
|
|
|
-+// SPDX-License-Identifier: ISC
|
|
|
-+/*
|
|
|
-+ * Device Tree file for the USRobotics USR8200 firewall
|
|
|
-+ * VPN and NAS. Based on know-how from Peter Denison.
|
|
|
-+ *
|
|
|
-+ * This machine is based on IXP422, the USR internal codename
|
|
|
-+ * is "Jeeves".
|
|
|
-+ */
|
|
|
-+
|
|
|
-+/dts-v1/;
|
|
|
-+
|
|
|
-+#include "intel-ixp42x.dtsi"
|
|
|
-+#include <dt-bindings/input/input.h>
|
|
|
-+
|
|
|
-+/ {
|
|
|
-+ model = "USRobotics USR8200";
|
|
|
-+ compatible = "usr,usr8200", "intel,ixp42x";
|
|
|
-+ #address-cells = <1>;
|
|
|
-+ #size-cells = <1>;
|
|
|
-+
|
|
|
-+ memory@0 {
|
|
|
-+ device_type = "memory";
|
|
|
-+ reg = <0x00000000 0x4000000>;
|
|
|
-+ };
|
|
|
-+
|
|
|
-+ chosen {
|
|
|
-+ bootargs = "console=ttyS0,115200n8";
|
|
|
-+ stdout-path = "uart1:115200n8";
|
|
|
-+ };
|
|
|
-+
|
|
|
-+ aliases {
|
|
|
-+ /* These are switched around */
|
|
|
-+ serial0 = &uart1;
|
|
|
-+ serial1 = &uart0;
|
|
|
-+ };
|
|
|
-+
|
|
|
-+ leds {
|
|
|
-+ compatible = "gpio-leds";
|
|
|
-+ ieee1394_led: led-1394 {
|
|
|
-+ label = "usr8200:green:1394";
|
|
|
-+ gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
|
|
|
-+ default-state = "off";
|
|
|
-+ };
|
|
|
-+ usb1_led: led-usb1 {
|
|
|
-+ label = "usr8200:green:usb1";
|
|
|
-+ gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
|
|
|
-+ default-state = "off";
|
|
|
-+ };
|
|
|
-+ usb2_led: led-usb2 {
|
|
|
-+ label = "usr8200:green:usb2";
|
|
|
-+ gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
|
|
|
-+ default-state = "off";
|
|
|
-+ };
|
|
|
-+ wireless_led: led-wireless {
|
|
|
-+ /*
|
|
|
-+ * This LED is mounted inside the case but cannot be
|
|
|
-+ * seen from the outside: probably USR planned at one
|
|
|
-+ * point for the device to have a wireless card, then
|
|
|
-+ * changed their mind and didn't mount it, leaving the
|
|
|
-+ * LED in place.
|
|
|
-+ */
|
|
|
-+ label = "usr8200:green:wireless";
|
|
|
-+ gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
|
|
|
-+ default-state = "off";
|
|
|
-+ };
|
|
|
-+ pwr_led: led-pwr {
|
|
|
-+ label = "usr8200:green:pwr";
|
|
|
-+ gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
|
|
|
-+ default-state = "on";
|
|
|
-+ linux,default-trigger = "heartbeat";
|
|
|
-+ };
|
|
|
-+ };
|
|
|
-+
|
|
|
-+ gpio_keys {
|
|
|
-+ compatible = "gpio-keys";
|
|
|
-+
|
|
|
-+ button-reset {
|
|
|
-+ wakeup-source;
|
|
|
-+ linux,code = <KEY_RESTART>;
|
|
|
-+ label = "reset";
|
|
|
-+ gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
|
|
|
-+ };
|
|
|
-+ };
|
|
|
-+
|
|
|
-+ soc {
|
|
|
-+ bus@c4000000 {
|
|
|
-+ flash@0,0 {
|
|
|
-+ compatible = "intel,ixp4xx-flash", "cfi-flash";
|
|
|
-+ bank-width = <2>;
|
|
|
-+ /* Enable writes on the expansion bus */
|
|
|
-+ intel,ixp4xx-eb-write-enable = <1>;
|
|
|
-+ /* 16 MB of Flash mapped in at CS0 */
|
|
|
-+ reg = <0 0x00000000 0x1000000>;
|
|
|
-+
|
|
|
-+ partitions {
|
|
|
-+ compatible = "redboot-fis";
|
|
|
-+ /* Eraseblock at 0x0fe0000 */
|
|
|
-+ fis-index-block = <0x7f>;
|
|
|
-+ };
|
|
|
-+ };
|
|
|
-+ rtc@2,0 {
|
|
|
-+ /* EPSON RTC7301 DG DIL-capsule */
|
|
|
-+ compatible = "epson,rtc7301dg";
|
|
|
-+ /*
|
|
|
-+ * These timing settings were found in the boardfile patch:
|
|
|
-+ * IXP4XX_EXP_CS2 = 0x3fff000 | IXP4XX_EXP_BUS_SIZE(0) | IXP4XX_EXP_BUS_WR_EN |
|
|
|
-+ * IXP4XX_EXP_BUS_CS_EN | IXP4XX_EXP_BUS_BYTE_EN;
|
|
|
-+ */
|
|
|
-+ intel,ixp4xx-eb-t1 = <0>; // no cycles extra address phase
|
|
|
-+ intel,ixp4xx-eb-t2 = <0>; // no cycles extra setup phase
|
|
|
-+ intel,ixp4xx-eb-t3 = <15>; // 15 cycles extra strobe phase
|
|
|
-+ intel,ixp4xx-eb-t4 = <3>; // 3 cycles extra hold phase
|
|
|
-+ intel,ixp4xx-eb-t5 = <15>; // 15 cycles extra recovery phase
|
|
|
-+ intel,ixp4xx-eb-cycle-type = <0>; // Intel cycle
|
|
|
-+ intel,ixp4xx-eb-byte-access-on-halfword = <0>;
|
|
|
-+ intel,ixp4xx-eb-mux-address-and-data = <0>;
|
|
|
-+ intel,ixp4xx-eb-ahb-split-transfers = <0>;
|
|
|
-+ intel,ixp4xx-eb-write-enable = <1>;
|
|
|
-+ intel,ixp4xx-eb-byte-access = <1>;
|
|
|
-+ /* 512 bytes at CS2 */
|
|
|
-+ reg = <2 0x00000000 0x0000200>;
|
|
|
-+ reg-io-width = <1>;
|
|
|
-+ native-endian;
|
|
|
-+ /* FIXME: try to check if there is an IRQ for the RTC? */
|
|
|
-+ };
|
|
|
-+ };
|
|
|
-+
|
|
|
-+ pci@c0000000 {
|
|
|
-+ status = "okay";
|
|
|
-+
|
|
|
-+ /*
|
|
|
-+ * Taken from USR8200 boardfile from OpenWrt
|
|
|
-+ *
|
|
|
-+ * We have 3 slots (IDSEL) with partly swizzled IRQs on slot 16.
|
|
|
-+ * We assume the same IRQ for all pins on the remaining slots, that
|
|
|
-+ * is what the boardfile was doing.
|
|
|
-+ */
|
|
|
-+ #interrupt-cells = <1>;
|
|
|
-+ interrupt-map-mask = <0xf800 0 0 7>;
|
|
|
-+ interrupt-map =
|
|
|
-+ /* IDSEL 14 used for "Wireless" in the board file */
|
|
|
-+ <0x7000 0 0 1 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 14 is irq 7 */
|
|
|
-+ /* IDSEL 15 used for VIA VT6307 IEEE 1394 Firewire */
|
|
|
-+ <0x7800 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 15 is irq 8 */
|
|
|
-+ /* IDSEL 16 used for VIA VT6202 USB 2.0 4+1 */
|
|
|
-+ <0x8000 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 16 is irq 11 */
|
|
|
-+ <0x8000 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 16 is irq 10 */
|
|
|
-+ <0x8000 0 0 3 &gpio0 9 IRQ_TYPE_LEVEL_LOW>; /* INT C on slot 16 is irq 9 */
|
|
|
-+ };
|
|
|
-+
|
|
|
-+ gpio@c8004000 {
|
|
|
-+ /* Enable clock out on GPIO 15 */
|
|
|
-+ intel,ixp4xx-gpio15-clkout;
|
|
|
-+ };
|
|
|
-+
|
|
|
-+ /* EthB WAN */
|
|
|
-+ ethernet@c8009000 {
|
|
|
-+ status = "okay";
|
|
|
-+ queue-rx = <&qmgr 3>;
|
|
|
-+ queue-txready = <&qmgr 20>;
|
|
|
-+ phy-mode = "rgmii";
|
|
|
-+ phy-handle = <&phy9>;
|
|
|
-+
|
|
|
-+ mdio {
|
|
|
-+ #address-cells = <1>;
|
|
|
-+ #size-cells = <0>;
|
|
|
-+
|
|
|
-+ phy9: ethernet-phy@9 {
|
|
|
-+ reg = <9>;
|
|
|
-+ };
|
|
|
-+
|
|
|
-+ /* The switch uses MDIO addresses 16 thru 31 */
|
|
|
-+ switch@16 {
|
|
|
-+ compatible = "marvell,mv88e6060";
|
|
|
-+ reg = <16>;
|
|
|
-+
|
|
|
-+ ports {
|
|
|
-+ #address-cells = <1>;
|
|
|
-+ #size-cells = <0>;
|
|
|
-+
|
|
|
-+ port@0 {
|
|
|
-+ reg = <0>;
|
|
|
-+ label = "lan1";
|
|
|
-+ };
|
|
|
-+
|
|
|
-+ port@1 {
|
|
|
-+ reg = <1>;
|
|
|
-+ label = "lan2";
|
|
|
-+ };
|
|
|
-+
|
|
|
-+ port@2 {
|
|
|
-+ reg = <2>;
|
|
|
-+ label = "lan3";
|
|
|
-+ };
|
|
|
-+
|
|
|
-+ port@3 {
|
|
|
-+ reg = <3>;
|
|
|
-+ label = "lan4";
|
|
|
-+ };
|
|
|
-+
|
|
|
-+ port@5 {
|
|
|
-+ /* Port 5 is the CPU port according to the MV88E6060 datasheet */
|
|
|
-+ reg = <5>;
|
|
|
-+ phy-mode = "rgmii-id";
|
|
|
-+ ethernet = <ðc>;
|
|
|
-+ label = "cpu";
|
|
|
-+ fixed-link {
|
|
|
-+ speed = <100>;
|
|
|
-+ full-duplex;
|
|
|
-+ };
|
|
|
-+ };
|
|
|
-+ };
|
|
|
-+ };
|
|
|
-+ };
|
|
|
-+ };
|
|
|
-+
|
|
|
-+ /* EthC LAN connected to the Marvell DSA Switch */
|
|
|
-+ ethc: ethernet@c800a000 {
|
|
|
-+ status = "okay";
|
|
|
-+ queue-rx = <&qmgr 4>;
|
|
|
-+ queue-txready = <&qmgr 21>;
|
|
|
-+ phy-mode = "rgmii";
|
|
|
-+ fixed-link {
|
|
|
-+ speed = <100>;
|
|
|
-+ full-duplex;
|
|
|
-+ };
|
|
|
-+ };
|
|
|
-+ };
|
|
|
-+};
|
Linus Walleij