brcm63xx: add initial support for BCM963268BU_P300 reference board

Only netboot tested, so no images or now.
GbE ports are only working in FE mode, and leds do not work.

Signed-off-by: Jonas Gorski <[email protected]>

SVN-Revision: 39679

target/linux/brcm63xx/base-files/etc/uci-defaults/02_network

@@ -109,6 +109,12 @@ VW6339GU)
 	ucidef_add_switch_vlan "switch0" "2" "4 8t"
 	;;
 
+963268BU_P300)
+	ucidef_set_interface_lan "eth0.1"
+	ucidef_add_switch "switch0" "1" "1"
+	ucidef_add_switch_vlan "switch0" "1" "0 3 4 5 6 7 8t"
+	;;
+
 *)
 	ucidef_set_interfaces_lan_wan "eth1" "eth0"
 	;;

target/linux/brcm63xx/patches-3.10/560-board_963268gu_p300.patch

@@ -0,0 +1,142 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -4475,6 +4475,131 @@ static struct board_info __initdata boar
+  * known 63268/63269 boards
+  */
+ #ifdef CONFIG_BCM63XX_CPU_63268
++static struct board_info __initdata board_963268bu_p300 = {
++	.name				= "963268BU_P300",
++	.expected_cpu_id		= 0x63268,
++
++	.has_uart0			= 1,
++
++	.has_ehci0			= 1,
++	.has_ohci0			= 1,
++	.num_usbh_ports			= 1,
++
++	.has_usbd			= 1,
++
++	.usbd = {
++		.use_fullspeed		= 0,
++		.port_no		= 0,
++	},
++
++	.has_enetsw			= 1,
++
++	.enetsw = {
++		.used_ports = {
++			[0] = {
++				.used	= 1,
++				.phy_id	= 17,
++				.name	= "FE1",
++			},
++
++			[3] = {
++				.used	= 1,
++				.phy_id	= 4,
++				.name	= "GbE2",
++			},
++
++			[4] = {
++				.used	= 1,
++				.phy_id	= 0,
++				.name	= "GbE3",
++			},
++
++			[5] = {
++				.used	= 1,
++				.phy_id	= 1,
++				.name	= "GbE1",
++			},
++
++			[6] = {
++				.used	= 1,
++				.phy_id	= 24,
++				.name	= "GbE4",
++			},
++
++			[7] = {
++				.used	= 1,
++				.phy_id	= 25,
++				.name	= "GbE5",
++			},
++		},
++	},
++
++	.leds = {
++		{
++			.name		= "963268BU_P300:green:power",
++			.gpio		= 20,
++			.active_low	= 1,
++		},
++		{
++			.name		= "963268BU_P300:red:power",
++			.gpio		= 21,
++			.active_low	= 1,
++		},
++		{
++			.name		= "963268BU_P300:green:internet",
++			.gpio		= 8,
++			.active_low	= 1,
++		},
++		{
++			.name		= "963268BU_P300:red:internet",
++			.gpio		= 2,
++			.active_low	= 1,
++		},
++		{
++			.name		= "963268BU_P300:green:adsl",
++			.gpio		= 3,
++			.active_low	= 1,
++		},
++		{
++			.name		= "963268BU_P300:green:wps",
++			.gpio		= 7,
++			.active_low	= 1,
++		},
++		{
++			.name		= "963268BU_P300:green:voip1",
++			.gpio		= 4,
++			.active_low	= 1,
++		},
++		{
++			.name		= "963268BU_P300:green:voip2",
++			.gpio		= 5,
++			.active_low	= 1,
++		},
++		{
++			.name		= "963268BU_P300:green:pots",
++			.gpio		= 6,
++			.active_low	= 1,
++		},
++	},
++
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 32,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++		{
++			.desc		= "wps",
++			.gpio		= 33,
++			.type		= EV_KEY,
++			.code		= KEY_WPS_BUTTON,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++	},
++};
++
+ static struct board_info __initdata board_963269bhr = {
+ 	.name				= "963269BHR",
+ 	.expected_cpu_id		= 0x63268,
+@@ -4729,6 +4854,7 @@ static const struct board_info __initcon
+ 	&board_96368mvngr,
+ #endif
+ #ifdef CONFIG_BCM63XX_CPU_63268
++	&board_963268bu_p300,
+ 	&board_963269bhr,
+ 	&board_vw6339gu,
+ #endif

target/linux/brcm63xx/patches-3.10/801-ssb_export_fallback_sprom.patch

@@ -8,7 +8,7 @@
  #include <linux/spi/spi.h>
  #include <linux/spi/spi_gpio.h>
  #include <linux/spi/74x164.h>
-@@ -4739,7 +4740,7 @@ static const struct board_info __initcon
+@@ -4865,7 +4866,7 @@ static const struct board_info __initcon
   * bcm4318 WLAN work
   */
  #ifdef CONFIG_SSB_PCIHOST
@@ -17,7 +17,7 @@
  	.revision		= 0x02,
  	.board_rev		= 0x17,
  	.country_code		= 0x0,
-@@ -4759,6 +4760,7 @@ static struct ssb_sprom bcm63xx_sprom =
+@@ -4885,6 +4886,7 @@ static struct ssb_sprom bcm63xx_sprom =
  	.boardflags_lo		= 0x2848,
  	.boardflags_hi		= 0x0000,
  };