|
|
@@ -0,0 +1,114 @@
|
|
|
+Index: b/arch/mips/bcm63xx/boards/board_bcm963xx.c
|
|
|
+===================================================================
|
|
|
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c 2011-03-21 08:29:36.500387994 +0000
|
|
|
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c 2011-03-31 12:35:08.209787004 +0100
|
|
|
+@@ -845,6 +845,63 @@
|
|
|
+ },
|
|
|
+ };
|
|
|
+
|
|
|
++ static struct board_info __initdata board_V2500V_BB = {
|
|
|
++ .name = "V2500V_BB",
|
|
|
++ .expected_cpu_id = 0x6348,
|
|
|
++
|
|
|
++ .has_uart0 = 1,
|
|
|
++ .has_enet0 = 1,
|
|
|
++ .has_enet1 = 1,
|
|
|
++ .has_pci = 1,
|
|
|
++
|
|
|
++ .enet0 = {
|
|
|
++ .has_phy = 1,
|
|
|
++ .use_internal_phy = 1,
|
|
|
++ },
|
|
|
++ .enet1 = {
|
|
|
++ .force_speed_100 = 1,
|
|
|
++ .force_duplex_full = 1,
|
|
|
++ },
|
|
|
++
|
|
|
++ .leds = {
|
|
|
++ {
|
|
|
++ .name = "power:green",
|
|
|
++ .gpio = 0,
|
|
|
++ .active_low = 1,
|
|
|
++ .default_trigger = "default-on",
|
|
|
++ },
|
|
|
++ {
|
|
|
++ .name = "power:red",
|
|
|
++ .gpio = 1,
|
|
|
++ .active_low = 1,
|
|
|
++ },
|
|
|
++ {
|
|
|
++ .name = "adsl",
|
|
|
++ .gpio = 2,
|
|
|
++ .active_low = 1,
|
|
|
++ },
|
|
|
++ { .name = "ppp",
|
|
|
++ .gpio = 3,
|
|
|
++ .active_low = 1,
|
|
|
++ },
|
|
|
++ {
|
|
|
++ .name = "wireless",
|
|
|
++ .gpio = 6,
|
|
|
++ .active_low = 1,
|
|
|
++ },
|
|
|
++ },
|
|
|
++ .buttons = {
|
|
|
++ {
|
|
|
++ .desc = "reset",
|
|
|
++ .gpio = 31,
|
|
|
++ .active_low = 1,
|
|
|
++ .type = EV_KEY,
|
|
|
++ .code = KEY_RESTART,
|
|
|
++ .threshold = 3,
|
|
|
++ },
|
|
|
++ },
|
|
|
++};
|
|
|
++
|
|
|
+ #endif
|
|
|
+
|
|
|
+ /*
|
|
|
+@@ -1830,6 +1887,7 @@
|
|
|
+ &board_spw500v,
|
|
|
+ &board_ct536_ct5621,
|
|
|
+ &board_96348sv,
|
|
|
++ &board_V2500V_BB,
|
|
|
+ #endif
|
|
|
+
|
|
|
+ #ifdef CONFIG_BCM63XX_CPU_6358
|
|
|
+@@ -1977,6 +2035,22 @@
|
|
|
+ val &= MPI_CSBASE_BASE_MASK;
|
|
|
+ }
|
|
|
+ boot_addr = (u8 *)KSEG1ADDR(val);
|
|
|
++ printk(KERN_INFO PFX "Boot address 0x%08x\n",(unsigned int)boot_addr);
|
|
|
++
|
|
|
++ /* BT Voyager 2500V (RTA1046VW PCB) has 8 Meg flash used as two */
|
|
|
++ /* banks of 4 Meg. The byte at 0xBF800000 identifies the back to use.*/
|
|
|
++ /* Loading firmware from the CFE Prompt always loads to Bank 0 */
|
|
|
++ /* Do an early check of CFE and then select bank 0 */
|
|
|
++
|
|
|
++ if (boot_addr == (u8 *)0xbf800000) {
|
|
|
++ u8 *tmp_boot_addr;
|
|
|
++ tmp_boot_addr = (u8 *)0xbfc00000; // Address of Bank 0
|
|
|
++ memcpy(&nvram, tmp_boot_addr + BCM963XX_NVRAM_OFFSET, sizeof(nvram));
|
|
|
++ if (!strcmp(nvram.name, "V2500V_BB")) {
|
|
|
++ printk(KERN_INFO PFX "V2500V: nvram bank 0\n");
|
|
|
++ boot_addr = (u8 *)0xbfc00000; // Bank 0
|
|
|
++ }
|
|
|
++ }
|
|
|
+
|
|
|
+ /* dump cfe version */
|
|
|
+ cfe = boot_addr + BCM963XX_CFE_VERSION_OFFSET;
|
|
|
+@@ -2184,6 +2258,14 @@
|
|
|
+ val = bcm_mpi_readl(MPI_CSBASE_REG(0));
|
|
|
+ val &= MPI_CSBASE_BASE_MASK;
|
|
|
+ }
|
|
|
++
|
|
|
++ /* BT Voyager 2500V has 8 Meg flash in two 4 Meg banks */
|
|
|
++ /* Loading from CFE always uses Bank 0 */
|
|
|
++ if (!strcmp(board.name, "V2500V_BB")) {
|
|
|
++ printk(KERN_INFO PFX "V2500V: Start in Bank 0\n");
|
|
|
++ val = val + 0x400000; // Select Bank 0 start address
|
|
|
++ }
|
|
|
++
|
|
|
+ mtd_resources[0].start = val;
|
|
|
+ mtd_resources[0].end = 0x1FFFFFFF;
|
|
|
+
|
Florian Fainelli