remove 2.6.26 specific stuff

SVN-Revision: 14493

target/linux/ar71xx/config-2.6.26

@@ -1,266 +0,0 @@
-CONFIG_32BIT=y
-# CONFIG_64BIT is not set
-# CONFIG_8139TOO is not set
-CONFIG_ADM6996_PHY=y
-CONFIG_AG71XX=y
-# CONFIG_AR71XX_EARLY_SERIAL is not set
-CONFIG_AR71XX_MACH_AP83=y
-CONFIG_AR71XX_MACH_AW_NR580=y
-CONFIG_AR71XX_MACH_GENERIC=y
-CONFIG_AR71XX_MACH_MZK_W04NU=y
-CONFIG_AR71XX_MACH_MZK_W300NH=y
-CONFIG_AR71XX_MACH_PB42=y
-CONFIG_AR71XX_MACH_RB_4XX=y
-CONFIG_AR71XX_MACH_TEW_632BRP=y
-CONFIG_AR71XX_MACH_UBNT=y
-CONFIG_AR71XX_MACH_WNR2000=y
-CONFIG_AR71XX_MACH_WP543=y
-CONFIG_AR71XX_WDT=y
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
-CONFIG_ARCH_POPULATES_NODE_MAP=y
-# CONFIG_ARCH_SUPPORTS_MSI is not set
-CONFIG_ARCH_SUPPORTS_OPROFILE=y
-CONFIG_ARCH_SUSPEND_POSSIBLE=y
-CONFIG_ATHEROS_AR71XX=y
-CONFIG_BASE_SMALL=0
-# CONFIG_BCM47XX is not set
-CONFIG_BITREVERSE=y
-# CONFIG_BROADCOM_PHY is not set
-CONFIG_CEVT_R4K=y
-CONFIG_CLASSIC_RCU=y
-CONFIG_CMDLINE="rootfstype=squashfs,yaffs,jffs2 noinitrd console=ttyS0,115200 init=/etc/preinit"
-CONFIG_CPU_BIG_ENDIAN=y
-CONFIG_CPU_HAS_LLSC=y
-CONFIG_CPU_HAS_PREFETCH=y
-CONFIG_CPU_HAS_SYNC=y
-# CONFIG_CPU_LITTLE_ENDIAN is not set
-# CONFIG_CPU_LOONGSON2 is not set
-CONFIG_CPU_MIPS32=y
-# CONFIG_CPU_MIPS32_R1 is not set
-CONFIG_CPU_MIPS32_R2=y
-# CONFIG_CPU_MIPS64_R1 is not set
-# CONFIG_CPU_MIPS64_R2 is not set
-CONFIG_CPU_MIPSR2=y
-# CONFIG_CPU_NEVADA is not set
-# CONFIG_CPU_R10000 is not set
-# CONFIG_CPU_R3000 is not set
-# CONFIG_CPU_R4300 is not set
-# CONFIG_CPU_R4X00 is not set
-# CONFIG_CPU_R5000 is not set
-# CONFIG_CPU_R5432 is not set
-# CONFIG_CPU_R6000 is not set
-# CONFIG_CPU_R8000 is not set
-# CONFIG_CPU_RM7000 is not set
-# CONFIG_CPU_RM9000 is not set
-# CONFIG_CPU_SB1 is not set
-CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
-CONFIG_CPU_SUPPORTS_HIGHMEM=y
-# CONFIG_CPU_TX39XX is not set
-# CONFIG_CPU_TX49XX is not set
-# CONFIG_CPU_VR41XX is not set
-CONFIG_CSRC_R4K=y
-CONFIG_DEVPORT=y
-# CONFIG_DM9000 is not set
-CONFIG_DMA_NEED_PCI_MAP_STATE=y
-CONFIG_DMA_NONCOHERENT=y
-# CONFIG_E1000E_ENABLED is not set
-CONFIG_EARLY_PRINTK=y
-# CONFIG_FIXED_PHY is not set
-CONFIG_FS_POSIX_ACL=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
-CONFIG_GENERIC_CMOS_UPDATE=y
-# CONFIG_GENERIC_FIND_FIRST_BIT is not set
-CONFIG_GENERIC_FIND_NEXT_BIT=y
-CONFIG_GENERIC_GPIO=y
-# CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ is not set
-CONFIG_GPIO_SYSFS=y
-CONFIG_HAS_DMA=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT=y
-# CONFIG_HAVE_DMA_ATTRS is not set
-CONFIG_HAVE_GPIO_LIB=y
-CONFIG_HAVE_IDE=y
-# CONFIG_HAVE_KPROBES is not set
-# CONFIG_HAVE_KRETPROBES is not set
-CONFIG_HAVE_OPROFILE=y
-CONFIG_HW_HAS_PCI=y
-CONFIG_HW_RANDOM=m
-# CONFIG_I2C is not set
-# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
-# CONFIG_IBM_NEW_EMAC_RGMII is not set
-# CONFIG_IBM_NEW_EMAC_TAH is not set
-# CONFIG_IBM_NEW_EMAC_ZMII is not set
-CONFIG_ICPLUS_PHY=y
-# CONFIG_IDE is not set
-CONFIG_INITRAMFS_ROOT_GID=0
-CONFIG_INITRAMFS_ROOT_UID=0
-CONFIG_INITRAMFS_SOURCE="../../root"
-CONFIG_IPV6_NDISC_NODETYPE=y
-CONFIG_IRQ_CPU=y
-# CONFIG_IWLWIFI_LEDS is not set
-# CONFIG_LEDS_ALIX is not set
-CONFIG_LEDS_GPIO=y
-# CONFIG_LEMOTE_FULONG is not set
-# CONFIG_M25PXX_USE_FAST_READ is not set
-# CONFIG_MACH_ALCHEMY is not set
-# CONFIG_MACH_DECSTATION is not set
-# CONFIG_MACH_JAZZ is not set
-# CONFIG_MACH_VR41XX is not set
-# CONFIG_MDIO_BITBANG is not set
-CONFIG_MICREL_PHY=y
-CONFIG_MIPS=y
-# CONFIG_MIPS_ATLAS is not set
-# CONFIG_MIPS_COBALT is not set
-CONFIG_MIPS_L1_CACHE_SHIFT=5
-CONFIG_MIPS_MACHINE=y
-# CONFIG_MIPS_MALTA is not set
-CONFIG_MIPS_MT_DISABLED=y
-# CONFIG_MIPS_MT_SMP is not set
-# CONFIG_MIPS_MT_SMTC is not set
-# CONFIG_MIPS_SEAD is not set
-# CONFIG_MIPS_SIM is not set
-CONFIG_MTD=y
-# CONFIG_MTD_ABSENT is not set
-# CONFIG_MTD_ALAUDA is not set
-CONFIG_MTD_BLKDEVS=y
-CONFIG_MTD_BLOCK=y
-# CONFIG_MTD_BLOCK2MTD is not set
-# CONFIG_MTD_CFI is not set
-CONFIG_MTD_CFI_I1=y
-CONFIG_MTD_CFI_I2=y
-# CONFIG_MTD_CFI_I4 is not set
-# CONFIG_MTD_CFI_I8 is not set
-CONFIG_MTD_CHAR=y
-# CONFIG_MTD_CMDLINE_PARTS is not set
-# CONFIG_MTD_COMPLEX_MAPPINGS is not set
-CONFIG_MTD_CONCAT=y
-# CONFIG_MTD_DEBUG is not set
-# CONFIG_MTD_DOC2000 is not set
-# CONFIG_MTD_DOC2001 is not set
-# CONFIG_MTD_DOC2001PLUS is not set
-# CONFIG_MTD_JEDECPROBE is not set
-CONFIG_MTD_M25P80=y
-CONFIG_MTD_MAP_BANK_WIDTH_1=y
-# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
-CONFIG_MTD_MAP_BANK_WIDTH_2=y
-# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
-CONFIG_MTD_MAP_BANK_WIDTH_4=y
-# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
-# CONFIG_MTD_MTDRAM is not set
-CONFIG_MTD_MYLOADER_PARTS=y
-CONFIG_MTD_NAND=y
-# CONFIG_MTD_NAND_CAFE is not set
-# CONFIG_MTD_NAND_DISKONCHIP is not set
-# CONFIG_MTD_NAND_ECC_SMC is not set
-CONFIG_MTD_NAND_IDS=y
-# CONFIG_MTD_NAND_MUSEUM_IDS is not set
-# CONFIG_MTD_NAND_NANDSIM is not set
-# CONFIG_MTD_NAND_PLATFORM is not set
-CONFIG_MTD_NAND_RB4XX=y
-# CONFIG_MTD_NAND_VERIFY_WRITE is not set
-# CONFIG_MTD_ONENAND is not set
-CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_PHRAM is not set
-# CONFIG_MTD_PLATRAM is not set
-# CONFIG_MTD_PMC551 is not set
-# CONFIG_MTD_RAM is not set
-CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-2
-CONFIG_MTD_REDBOOT_PARTS=y
-CONFIG_MTD_REDBOOT_PARTS_READONLY=y
-# CONFIG_MTD_ROM is not set
-# CONFIG_MTD_SLRAM is not set
-CONFIG_MYLOADER=y
-# CONFIG_NATSEMI is not set
-# CONFIG_NE2K_PCI is not set
-# CONFIG_NET_VENDOR_3COM is not set
-# CONFIG_NO_IOPORT is not set
-CONFIG_PAGEFLAGS_EXTENDED=y
-# CONFIG_PAGE_SIZE_16KB is not set
-CONFIG_PAGE_SIZE_4KB=y
-# CONFIG_PAGE_SIZE_64KB is not set
-# CONFIG_PAGE_SIZE_8KB is not set
-CONFIG_PCI=y
-# CONFIG_PCIPCWATCHDOG is not set
-CONFIG_PCI_DOMAINS=y
-# CONFIG_PCSPKR_PLATFORM is not set
-CONFIG_PHYLIB=y
-# CONFIG_PMC_MSP is not set
-# CONFIG_PMC_YOSEMITE is not set
-# CONFIG_PNX8550_JBS is not set
-# CONFIG_PNX8550_STB810 is not set
-CONFIG_PROM_EMU=y
-# CONFIG_QSEMI_PHY is not set
-# CONFIG_R6040 is not set
-# CONFIG_REALTEK_PHY is not set
-CONFIG_RFKILL_LEDS=y
-CONFIG_RTC_LIB=y
-CONFIG_RWSEM_GENERIC_SPINLOCK=y
-CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
-CONFIG_SCSI_WAIT_SCAN=m
-# CONFIG_SERIAL_8250_EXTENDED is not set
-CONFIG_SERIAL_8250_NR_UARTS=1
-CONFIG_SERIAL_8250_RUNTIME_UARTS=1
-# CONFIG_SGI_IP22 is not set
-# CONFIG_SGI_IP27 is not set
-# CONFIG_SGI_IP28 is not set
-# CONFIG_SGI_IP32 is not set
-# CONFIG_SIBYTE_BIGSUR is not set
-# CONFIG_SIBYTE_CARMEL is not set
-# CONFIG_SIBYTE_CRHINE is not set
-# CONFIG_SIBYTE_CRHONE is not set
-# CONFIG_SIBYTE_LITTLESUR is not set
-# CONFIG_SIBYTE_RHONE is not set
-# CONFIG_SIBYTE_SENTOSA is not set
-# CONFIG_SIBYTE_SWARM is not set
-# CONFIG_SMSC_PHY is not set
-# CONFIG_SOFT_WATCHDOG is not set
-# CONFIG_SPARSEMEM_STATIC is not set
-# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
-CONFIG_SPI=y
-CONFIG_SPI_AR71XX=y
-CONFIG_SPI_BITBANG=y
-# CONFIG_SPI_GPIO is not set
-CONFIG_SPI_MASTER=y
-# CONFIG_SPI_SPIDEV is not set
-CONFIG_SSB_POSSIBLE=y
-CONFIG_SYSVIPC_SYSCTL=y
-CONFIG_SYS_HAS_CPU_MIPS32_R1=y
-CONFIG_SYS_HAS_CPU_MIPS32_R2=y
-CONFIG_SYS_HAS_EARLY_PRINTK=y
-CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
-CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
-CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y
-# CONFIG_TC35815 is not set
-CONFIG_TICK_ONESHOT=y
-# CONFIG_TOSHIBA_JMR3927 is not set
-# CONFIG_TOSHIBA_RBTX4927 is not set
-# CONFIG_TOSHIBA_RBTX4938 is not set
-CONFIG_TRAD_SIGNALS=y
-CONFIG_USB=m
-CONFIG_USB_EHCI_AR71XX=y
-CONFIG_USB_EHCI_HCD=m
-CONFIG_USB_EHCI_ROOT_HUB_TT=y
-CONFIG_USB_OHCI_AR71XX=y
-# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
-# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
-CONFIG_USB_OHCI_HCD=m
-CONFIG_USB_SUPPORT=y
-# CONFIG_USB_UHCI_HCD is not set
-# CONFIG_VGASTATE is not set
-# CONFIG_VIA_RHINE is not set
-CONFIG_VIDEO_MEDIA=m
-CONFIG_VIDEO_V4L2=m
-CONFIG_VIDEO_V4L2_COMMON=m
-CONFIG_YAFFS_9BYTE_TAGS=y
-CONFIG_YAFFS_ALWAYS_CHECK_CHUNK_ERASED=y
-CONFIG_YAFFS_AUTO_YAFFS2=y
-CONFIG_YAFFS_CHECKPOINT_RESERVED_BLOCKS=0
-# CONFIG_YAFFS_DISABLE_LAZY_LOAD is not set
-# CONFIG_YAFFS_DISABLE_WIDE_TNODES is not set
-CONFIG_YAFFS_FS=y
-CONFIG_YAFFS_SHORT_NAMES_IN_RAM=y
-CONFIG_YAFFS_YAFFS1=y
-CONFIG_YAFFS_YAFFS2=y
-CONFIG_ZONE_DMA_FLAG=0

target/linux/ar71xx/patches-2.6.26/001-ar71xx_core.patch

@@ -1,51 +0,0 @@
---- a/arch/mips/Makefile
-+++ b/arch/mips/Makefile
-@@ -597,6 +597,13 @@ core-$(CONFIG_TOSHIBA_RBTX4938) += arch/
- cflags-$(CONFIG_TOSHIBA_RBTX4938) += -Iinclude/asm-mips/mach-tx49xx
- load-$(CONFIG_TOSHIBA_RBTX4938) += 0xffffffff80100000
- 
-+#
-+# Atheros AR71xx
-+#
-+core-$(CONFIG_ATHEROS_AR71XX)	+= arch/mips/ar71xx/
-+cflags-$(CONFIG_ATHEROS_AR71XX)	+= -Iinclude/asm-mips/mach-ar71xx
-+load-$(CONFIG_ATHEROS_AR71XX)	+= 0xffffffff80060000
-+
- # temporary until string.h is fixed
- cflags-y += -ffreestanding
- 
---- a/arch/mips/Kconfig
-+++ b/arch/mips/Kconfig
-@@ -21,6 +21,24 @@ choice
- config MACH_ALCHEMY
- 	bool "Alchemy processor based machines"
- 
-+config ATHEROS_AR71XX
-+	bool "Atheros AR71xx based boards"
-+	select CEVT_R4K
-+	select CSRC_R4K
-+	select DMA_NONCOHERENT
-+	select HW_HAS_PCI
-+	select IRQ_CPU
-+	select GENERIC_GPIO
-+	select HAVE_GPIO_LIB
-+	select SYS_HAS_CPU_MIPS32_R1
-+	select SYS_HAS_CPU_MIPS32_R2
-+	select SYS_SUPPORTS_32BIT_KERNEL
-+	select SYS_SUPPORTS_BIG_ENDIAN
-+	select SYS_HAS_EARLY_PRINTK
-+	select MIPS_MACHINE
-+	help
-+	  Support for Atheros AR71xx based boards.
-+
- config BASLER_EXCITE
- 	bool "Basler eXcite smart camera"
- 	select CEVT_R4K
-@@ -687,6 +705,7 @@ config WR_PPMC
- 
- endchoice
- 
-+source "arch/mips/ar71xx/Kconfig"
- source "arch/mips/au1000/Kconfig"
- source "arch/mips/basler/excite/Kconfig"
- source "arch/mips/jazz/Kconfig"

target/linux/ar71xx/patches-2.6.26/002-ar71xx_pci.patch

@@ -1,10 +0,0 @@
---- a/arch/mips/pci/Makefile
-+++ b/arch/mips/pci/Makefile
-@@ -15,6 +15,7 @@ obj-$(CONFIG_MIPS_TX3927)	+= ops-tx3927.
- obj-$(CONFIG_PCI_VR41XX)	+= ops-vr41xx.o pci-vr41xx.o
- obj-$(CONFIG_NEC_CMBVR4133)	+= fixup-vr4133.o
- obj-$(CONFIG_MARKEINS)		+= ops-emma2rh.o pci-emma2rh.o fixup-emma2rh.o
-+obj-$(CONFIG_ATHEROS_AR71XX)	+= pci-ar71xx.o
- 
- #
- # These are still pretty much in the old state, watch, go blind.

target/linux/ar71xx/patches-2.6.26/003-ar71xx_usb_host.patch

@@ -1,70 +0,0 @@
---- a/drivers/usb/host/Kconfig
-+++ b/drivers/usb/host/Kconfig
-@@ -81,6 +81,12 @@ config USB_EHCI_BIG_ENDIAN_DESC
- 	depends on USB_EHCI_HCD && (440EPX || ARCH_IXP4XX)
- 	default y
- 
-+config USB_EHCI_AR71XX
-+	bool "USB EHCI support for AR71xx"
-+	depends on USB_EHCI_HCD && ATHEROS_AR71XX
-+	help
-+	  Support for Atheros AR71xx built-in EHCI controller
-+
- config USB_EHCI_FSL
- 	bool "Support for Freescale on-chip EHCI USB controller"
- 	depends on USB_EHCI_HCD && FSL_SOC
-@@ -152,6 +158,12 @@ config USB_OHCI_HCD
- 	  To compile this driver as a module, choose M here: the
- 	  module will be called ohci-hcd.
- 
-+config USB_OHCI_AR71XX
-+	bool "USB OHCI support for Atheros AR71xx"
-+	depends on USB_OHCI_HCD && ATHEROS_AR71XX
-+	help
-+	  Support for Atheros AR71xx built-in OHCI controller
-+
- config USB_OHCI_HCD_PPC_SOC
- 	bool "OHCI support for on-chip PPC USB controller"
- 	depends on USB_OHCI_HCD && (STB03xxx || PPC_MPC52xx)
---- a/drivers/usb/host/ehci-hcd.c
-+++ b/drivers/usb/host/ehci-hcd.c
-@@ -1034,6 +1034,11 @@ MODULE_LICENSE ("GPL");
- #define	PLATFORM_DRIVER		ixp4xx_ehci_driver
- #endif
- 
-+#ifdef CONFIG_USB_EHCI_AR71XX
-+#include "ehci-ar71xx.c"
-+#define PLATFORM_DRIVER		ehci_ar71xx_driver
-+#endif
-+
- #if !defined(PCI_DRIVER) && !defined(PLATFORM_DRIVER) && \
-     !defined(PS3_SYSTEM_BUS_DRIVER) && !defined(OF_PLATFORM_DRIVER)
- #error "missing bus glue for ehci-hcd"
---- a/drivers/usb/host/ohci.h
-+++ b/drivers/usb/host/ohci.h
-@@ -538,6 +538,11 @@ static inline struct usb_hcd *ohci_to_hc
- #define writel_be(val, addr)	out_be32((__force unsigned *)addr, val)
- #endif
- 
-+#if defined(CONFIG_ATHEROS_AR71XX)
-+#define readl_be(addr)		__raw_readl(addr)
-+#define writel_be(val, addr)	__raw_writel(addr, val)
-+#endif
-+
- static inline unsigned int _ohci_readl (const struct ohci_hcd *ohci,
- 					__hc32 __iomem * regs)
- {
---- a/drivers/usb/host/ohci-hcd.c
-+++ b/drivers/usb/host/ohci-hcd.c
-@@ -1057,6 +1057,11 @@ MODULE_LICENSE ("GPL");
- #define SM501_OHCI_DRIVER	ohci_hcd_sm501_driver
- #endif
- 
-+#ifdef CONFIG_USB_OHCI_AR71XX
-+#include "ohci-ar71xx.c"
-+#define PLATFORM_DRIVER		ohci_hcd_ar71xx_driver
-+#endif
-+
- #if	!defined(PCI_DRIVER) &&		\
- 	!defined(PLATFORM_DRIVER) &&	\
- 	!defined(OF_PLATFORM_DRIVER) &&	\

target/linux/ar71xx/patches-2.6.26/004-ar71xx_spi_controller.patch

@@ -1,26 +0,0 @@
---- a/drivers/spi/Kconfig
-+++ b/drivers/spi/Kconfig
-@@ -52,6 +52,13 @@ config SPI_MASTER
- comment "SPI Master Controller Drivers"
- 	depends on SPI_MASTER
- 
-+config SPI_AR71XX
-+	tristate "Atheros AR71xx SPI Controller"
-+	depends on SPI_MASTER && ATHEROS_AR71XX
-+	select SPI_BITBANG
-+	help
-+	  This is the SPI contoller driver for Atheros AR71xx.
-+
- config SPI_ATMEL
- 	tristate "Atmel SPI Controller"
- 	depends on (ARCH_AT91 || AVR32) && SPI_MASTER
---- a/drivers/spi/Makefile
-+++ b/drivers/spi/Makefile
-@@ -11,6 +11,7 @@ endif
- obj-$(CONFIG_SPI_MASTER)		+= spi.o
- 
- # SPI master controller drivers (bus)
-+obj-$(CONFIG_SPI_AR71XX)		+= ar71xx_spi.o
- obj-$(CONFIG_SPI_ATMEL)			+= atmel_spi.o
- obj-$(CONFIG_SPI_BFIN)			+= spi_bfin5xx.o
- obj-$(CONFIG_SPI_BITBANG)		+= spi_bitbang.o

target/linux/ar71xx/patches-2.6.26/005-ar71xx_mac_driver.patch

@@ -1,21 +0,0 @@
---- a/drivers/net/Kconfig
-+++ b/drivers/net/Kconfig
-@@ -2060,6 +2060,8 @@ config ACENIC_OMIT_TIGON_I
- 
- 	  The safe and default value for this is N.
- 
-+source drivers/net/ag71xx/Kconfig
-+
- config DL2K
- 	tristate "DL2000/TC902x-based Gigabit Ethernet support"
- 	depends on PCI
---- a/drivers/net/Makefile
-+++ b/drivers/net/Makefile
-@@ -2,6 +2,7 @@
- # Makefile for the Linux network (ethercard) device drivers.
- #
- 
-+obj-$(CONFIG_AG71XX) += ag71xx/
- obj-$(CONFIG_E1000) += e1000/
- obj-$(CONFIG_E1000E) += e1000e/
- obj-$(CONFIG_IBM_EMAC) += ibm_emac/

target/linux/ar71xx/patches-2.6.26/006-ar71xx_wdt_driver.patch

@@ -1,26 +0,0 @@
---- a/drivers/watchdog/Kconfig
-+++ b/drivers/watchdog/Kconfig
-@@ -683,6 +683,13 @@ config TXX9_WDT
- 	help
- 	  Hardware driver for the built-in watchdog timer on TXx9 MIPS SoCs.
- 
-+config AR71XX_WDT
-+	tristate "Atheros AR71xx Watchdog Timer"
-+	depends on ATHEROS_AR71XX
-+	help
-+	  Hardware driver for the built-in watchdog timer on the Atheros
-+	  AR71xx SoCs.
-+
- # PARISC Architecture
- 
- # POWERPC Architecture
---- a/drivers/watchdog/Makefile
-+++ b/drivers/watchdog/Makefile
-@@ -97,6 +97,7 @@ obj-$(CONFIG_WDT_RM9K_GPI) += rm9k_wdt.o
- obj-$(CONFIG_SIBYTE_WDOG) += sb_wdog.o
- obj-$(CONFIG_AR7_WDT) += ar7_wdt.o
- obj-$(CONFIG_TXX9_WDT) += txx9wdt.o
-+obj-$(CONFIG_AR71XX_WDT) += ar71xx_wdt.o
- 
- # PARISC Architecture
- 

target/linux/ar71xx/patches-2.6.26/100-mtd_m25p80_add_pm25lv_flash_support.patch

@@ -1,13 +0,0 @@
---- a/drivers/mtd/devices/m25p80.c
-+++ b/drivers/mtd/devices/m25p80.c
-@@ -455,6 +455,10 @@ static struct flash_info __devinitdata m
- 	{ "at26df161a", 0x1f4601, 64 * 1024, 32, SECT_4K, },
- 	{ "at26df321",  0x1f4701, 64 * 1024, 64, SECT_4K, },
- 
-+	/* PMC -- pm25x "blocks" are 32K, sectors are 4K */
-+	{ "pm25lv512",         0, 32 * 1024, 2, SECT_4K },
-+	{ "pm25lv010",         0, 32 * 1024, 4, SECT_4K },
-+
- 	/* Spansion -- single (large) sector size only, at least
- 	 * for the chips listed here (without boot sectors).
- 	 */

target/linux/ar71xx/patches-2.6.26/101-ksz8041_phy_driver.patch

@@ -1,23 +0,0 @@
---- a/drivers/net/phy/Kconfig
-+++ b/drivers/net/phy/Kconfig
-@@ -82,6 +82,11 @@ config MVSWITCH_PHY
- 	---help---
- 	  Currently supports the Marvell 88E6060 switch.
- 
-+config MICREL_PHY
-+	tristate "Drivers for Micrel/Kendin PHYs"
-+	---help---
-+	  Currently has a driver for the KSZ8041
-+
- config FIXED_PHY
- 	bool "Driver for MDIO Bus/PHY emulation with fixed speed/link PHYs"
- 	depends on PHYLIB=y
---- a/drivers/net/phy/Makefile
-+++ b/drivers/net/phy/Makefile
-@@ -16,5 +16,6 @@ obj-$(CONFIG_ICPLUS_PHY)	+= icplus.o
- obj-$(CONFIG_ADM6996_PHY)	+= adm6996.o
- obj-$(CONFIG_MVSWITCH_PHY)	+= mvswitch.o
- obj-$(CONFIG_REALTEK_PHY)	+= realtek.o
-+obj-$(CONFIG_MICREL_PHY)	+= micrel.o
- obj-$(CONFIG_FIXED_PHY)		+= fixed.o
- obj-$(CONFIG_MDIO_BITBANG)	+= mdio-bitbang.o

target/linux/ar71xx/patches-2.6.26/102-mtd_m25p80_add_myloader_parser.patch

@@ -1,22 +0,0 @@
---- a/drivers/mtd/devices/m25p80.c
-+++ b/drivers/mtd/devices/m25p80.c
-@@ -645,12 +645,17 @@ static int __devinit m25p_probe(struct s
- 		struct mtd_partition	*parts = NULL;
- 		int			nr_parts = 0;
- 
-+		static const char *part_probes[] = {
- #ifdef CONFIG_MTD_CMDLINE_PARTS
--		static const char *part_probes[] = { "cmdlinepart", NULL, };
-+						"cmdlinepart",
-+#endif
-+#ifdef CONFIG_MTD_MYLOADER_PARTS
-+						"MyLoader",
-+#endif
-+					       	NULL, };
- 
- 		nr_parts = parse_mtd_partitions(&flash->mtd,
- 				part_probes, &parts, 0);
--#endif
- 
- 		if (nr_parts <= 0 && data && data->parts) {
- 			parts = data->parts;

target/linux/ar71xx/patches-2.6.26/103-mtd_m25p80_add_en25p32_support.patch

@@ -1,12 +0,0 @@
---- a/drivers/mtd/devices/m25p80.c
-+++ b/drivers/mtd/devices/m25p80.c
-@@ -455,6 +455,9 @@ static struct flash_info __devinitdata m
- 	{ "at26df161a", 0x1f4601, 64 * 1024, 32, SECT_4K, },
- 	{ "at26df321",  0x1f4701, 64 * 1024, 64, SECT_4K, },
- 
-+	/* EON -- en25px */
-+	{ "en25p32", 0x1c2016, 64 * 1024, 64, },
-+
- 	/* PMC -- pm25x "blocks" are 32K, sectors are 4K */
- 	{ "pm25lv512",         0, 32 * 1024, 2, SECT_4K },
- 	{ "pm25lv010",         0, 32 * 1024, 4, SECT_4K },

target/linux/ar71xx/patches-2.6.26/104-mtd_m25p80_add_redboot_parser.patch

@@ -1,12 +0,0 @@
---- a/drivers/mtd/devices/m25p80.c
-+++ b/drivers/mtd/devices/m25p80.c
-@@ -655,6 +655,9 @@ static int __devinit m25p_probe(struct s
- #ifdef CONFIG_MTD_MYLOADER_PARTS
- 						"MyLoader",
- #endif
-+#ifdef CONFIG_MTD_REDBOOT_PARTS
-+						"RedBoot",
-+#endif
- 					       	NULL, };
- 
- 		nr_parts = parse_mtd_partitions(&flash->mtd,

target/linux/ar71xx/patches-2.6.26/105-mtd_m25p80_add_mx25lxxx_support.patch

@@ -1,14 +0,0 @@
---- a/drivers/mtd/devices/m25p80.c
-+++ b/drivers/mtd/devices/m25p80.c
-@@ -458,6 +458,11 @@ static struct flash_info __devinitdata m
- 	/* EON -- en25px */
- 	{ "en25p32", 0x1c2016, 64 * 1024, 64, },
- 
-+	/* Macronix -- mx25lxxx */
-+	{ "mx25l32",  0xc22016,  64 * 1024,  64, },
-+	{ "mx25l64",  0xc22017,  64 * 1024, 128, },
-+	{ "mx25l128", 0xc22018,  64 * 1024, 256, },
-+
- 	/* PMC -- pm25x "blocks" are 32K, sectors are 4K */
- 	{ "pm25lv512",         0, 32 * 1024, 2, SECT_4K },
- 	{ "pm25lv010",         0, 32 * 1024, 4, SECT_4K },

target/linux/ar71xx/patches-2.6.26/140-redboot_partition_scan.patch

@@ -1,54 +0,0 @@
---- a/drivers/mtd/redboot.c
-+++ b/drivers/mtd/redboot.c
-@@ -62,31 +62,32 @@ static int parse_redboot_partitions(stru
- 	static char nullstring[] = "unallocated";
- #endif
- 
-+	buf = vmalloc(master->erasesize);
-+	if (!buf)
-+		return -ENOMEM;
-+
-+ restart:
- 	if ( directory < 0 ) {
- 		offset = master->size + directory * master->erasesize;
--		while (master->block_isbad && 
-+		while (master->block_isbad &&
- 		       master->block_isbad(master, offset)) {
- 			if (!offset) {
- 			nogood:
- 				printk(KERN_NOTICE "Failed to find a non-bad block to check for RedBoot partition table\n");
-+				vfree(buf);
- 				return -EIO;
- 			}
- 			offset -= master->erasesize;
- 		}
- 	} else {
- 		offset = directory * master->erasesize;
--		while (master->block_isbad && 
-+		while (master->block_isbad &&
- 		       master->block_isbad(master, offset)) {
- 			offset += master->erasesize;
- 			if (offset == master->size)
- 				goto nogood;
- 		}
- 	}
--	buf = vmalloc(master->erasesize);
--
--	if (!buf)
--		return -ENOMEM;
--
- 	printk(KERN_NOTICE "Searching for RedBoot partition table in %s at offset 0x%lx\n",
- 	       master->name, offset);
- 
-@@ -158,6 +159,11 @@ static int parse_redboot_partitions(stru
- 	}
- 	if (i == numslots) {
- 		/* Didn't find it */
-+		if (offset + master->erasesize < master->size) {
-+			/* not at the end of the flash yet, maybe next block :) */
-+			directory++;
-+			goto restart;
-+		}
- 		printk(KERN_NOTICE "No RedBoot partition table detected in %s\n",
- 		       master->name);
- 		ret = 0;

target/linux/ar71xx/patches-2.6.26/200-rb4xx_nand_driver.patch

@@ -1,21 +0,0 @@
---- a/drivers/mtd/nand/Kconfig
-+++ b/drivers/mtd/nand/Kconfig
-@@ -386,4 +386,8 @@ config MTD_NAND_FSL_UPM
- 	  Enables support for NAND Flash chips wired onto Freescale PowerPC
- 	  processor localbus with User-Programmable Machine support.
- 
-+config MTD_NAND_RB4XX
-+	tristate "NAND flash driver for RouterBoard 4xx series"
-+	depends on MTD_NAND && ATHEROS_AR71XX
-+
- endif # MTD_NAND
---- a/drivers/mtd/nand/Makefile
-+++ b/drivers/mtd/nand/Makefile
-@@ -29,6 +29,7 @@ obj-$(CONFIG_MTD_NAND_CM_X270)		+= cmx27
- obj-$(CONFIG_MTD_NAND_BASLER_EXCITE)	+= excite_nandflash.o
- obj-$(CONFIG_MTD_NAND_PXA3xx)		+= pxa3xx_nand.o
- obj-$(CONFIG_MTD_NAND_PLATFORM)		+= plat_nand.o
-+obj-$(CONFIG_MTD_NAND_RB4XX)		+= rb4xx_nand.o
- obj-$(CONFIG_MTD_ALAUDA)		+= alauda.o
- obj-$(CONFIG_MTD_NAND_PASEMI)		+= pasemi_nand.o
- obj-$(CONFIG_MTD_NAND_ORION)		+= orion_nand.o

target/linux/ar71xx/patches-2.6.26/300-mips_fw_myloader.patch

@@ -1,22 +0,0 @@
---- a/arch/mips/Makefile
-+++ b/arch/mips/Makefile
-@@ -158,6 +158,7 @@ endif
- #
- libs-$(CONFIG_ARC)		+= arch/mips/fw/arc/
- libs-$(CONFIG_CFE)		+= arch/mips/fw/cfe/
-+libs-$(CONFIG_MYLOADER)		+= arch/mips/fw/myloader/
- libs-$(CONFIG_SNIPROM)		+= arch/mips/fw/sni/
- libs-y				+= arch/mips/fw/lib/
- libs-$(CONFIG_SIBYTE_CFE)	+= arch/mips/sibyte/cfe/
---- a/arch/mips/Kconfig
-+++ b/arch/mips/Kconfig
-@@ -874,6 +874,9 @@ config MIPS_NILE4
- config MIPS_DISABLE_OBSOLETE_IDE
- 	bool
- 
-+config MYLOADER
-+	bool
-+
- config SYNC_R4K
- 	bool
- 

target/linux/ar71xx/patches-2.6.26/301-enable_prom_emulator.patch

@@ -1,10 +0,0 @@
---- a/arch/mips/Kconfig
-+++ b/arch/mips/Kconfig
-@@ -36,6 +36,7 @@ config ATHEROS_AR71XX
- 	select SYS_SUPPORTS_BIG_ENDIAN
- 	select SYS_HAS_EARLY_PRINTK
- 	select MIPS_MACHINE
-+	select PROM_EMU
- 	help
- 	  Support for Atheros AR71xx based boards.
- 

target/linux/ar71xx/patches-2.6.26/901-get_c0_compare_irq_function.patch

@@ -1,29 +0,0 @@
---- a/arch/mips/kernel/traps.c
-+++ b/arch/mips/kernel/traps.c
-@@ -43,6 +43,7 @@
- #include <asm/mmu_context.h>
- #include <asm/types.h>
- #include <asm/stacktrace.h>
-+#include <asm/time.h>
- 
- extern asmlinkage void handle_int(void);
- extern asmlinkage void handle_tlbm(void);
-@@ -1464,6 +1465,8 @@ void __cpuinit per_cpu_trap_init(void)
- 	 */
- 	if (cpu_has_mips_r2) {
- 		cp0_compare_irq = (read_c0_intctl() >> 29) & 7;
-+		if (get_c0_compare_irq)
-+			cp0_compare_irq = get_c0_compare_irq();
- 		cp0_perfcount_irq = (read_c0_intctl() >> 26) & 7;
- 		if (cp0_perfcount_irq == cp0_compare_irq)
- 			cp0_perfcount_irq = -1;
---- a/include/asm-mips/time.h
-+++ b/include/asm-mips/time.h
-@@ -53,6 +53,7 @@ extern int (*perf_irq)(void);
- #ifdef CONFIG_CEVT_R4K
- extern int mips_clockevent_init(void);
- extern unsigned int __weak get_c0_compare_int(void);
-+extern unsigned int __weak get_c0_compare_irq(void);
- #else
- static inline int mips_clockevent_init(void)
- {

target/linux/ar71xx/patches-2.6.26/902-mips_clocksource_init_war.patch

@@ -1,65 +0,0 @@
---- a/arch/mips/kernel/cevt-r4k.c
-+++ b/arch/mips/kernel/cevt-r4k.c
-@@ -13,6 +13,22 @@
- #include <asm/smtc_ipi.h>
- #include <asm/time.h>
- 
-+/*
-+ * Compare interrupt can be routed and latched outside the core,
-+ * so a single execution hazard barrier may not be enough to give
-+ * it time to clear as seen in the Cause register.  4 time the
-+ * pipeline depth seems reasonably conservative, and empirically
-+ * works better in configurations with high CPU/bus clock ratios.
-+ */
-+
-+#define compare_change_hazard() \
-+	do { \
-+		irq_disable_hazard(); \
-+		irq_disable_hazard(); \
-+		irq_disable_hazard(); \
-+		irq_disable_hazard(); \
-+	} while (0)
-+
- static int mips_next_event(unsigned long delta,
-                            struct clock_event_device *evt)
- {
-@@ -28,6 +44,7 @@ static int mips_next_event(unsigned long
- 	cnt = read_c0_count();
- 	cnt += delta;
- 	write_c0_compare(cnt);
-+	compare_change_hazard();
- 	res = ((int)(read_c0_count() - cnt) > 0) ? -ETIME : 0;
- #ifdef CONFIG_MIPS_MT_SMTC
- 	evpe(vpflags);
-@@ -187,7 +204,7 @@ static int c0_compare_int_usable(void)
- 	 */
- 	if (c0_compare_int_pending()) {
- 		write_c0_compare(read_c0_count());
--		irq_disable_hazard();
-+		compare_change_hazard();
- 		if (c0_compare_int_pending())
- 			return 0;
- 	}
-@@ -196,7 +213,7 @@ static int c0_compare_int_usable(void)
- 		cnt = read_c0_count();
- 		cnt += delta;
- 		write_c0_compare(cnt);
--		irq_disable_hazard();
-+		compare_change_hazard();
- 		if ((int)(read_c0_count() - cnt) < 0)
- 		    break;
- 		/* increase delta if the timer was already expired */
-@@ -205,11 +222,12 @@ static int c0_compare_int_usable(void)
- 	while ((int)(read_c0_count() - cnt) <= 0)
- 		;	/* Wait for expiry  */
- 
-+	compare_change_hazard();
- 	if (!c0_compare_int_pending())
- 		return 0;
- 
- 	write_c0_compare(read_c0_count());
--	irq_disable_hazard();
-+	compare_change_hazard();
- 	if (c0_compare_int_pending())
- 		return 0;
-