adds support for Edimax BR-6524N

fixes #12754

Signed-off-by: <[email protected]>

SVN-Revision: 35020

target/linux/ramips/base-files/etc/diag.sh

@@ -36,6 +36,9 @@ get_status_led() {
 	argus-atp52b)
 		status_led="argus-atp52b:green:run"
 		;;
+	br6524n)
+		status_led="edimax:blue:power"
+		;;
 	dir-300-b1 | dir-600-b1 | dir-600-b2 | dir-615-h1 | dir-615-d | dir-620-a1)
 		status_led="d-link:green:status"
 		;;

target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom

@@ -59,6 +59,7 @@ case "$FIRMWARE" in
 	argus-atp52b | \
 	bc2 | \
 	broadway | \
+	br6524n | \
 	carambola | \
 	dir-615-h1 | \
 	dir-620-a1 | \

target/linux/ramips/base-files/etc/uci-defaults/leds

@@ -36,6 +36,9 @@ case $board in
 		set_usb_led "red:diskmounted"
 		set_wifi_led "red:wps_active"
 		;;
+	br6524n)
+		set_wifi_led "edimax:blue:wlan"
+		;;
 	dir-300-b1|\
 	dir-600-b1|\
 	dir-600-b2|\

target/linux/ramips/base-files/etc/uci-defaults/network

@@ -84,6 +84,7 @@ ramips_setup_interfaces()
 		ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
 		;;
 
+	br6524n | \
 	v11st-fe)
 		ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
 		ucidef_add_switch "switch0" "1" "1"

target/linux/ramips/base-files/lib/ramips.sh

@@ -71,6 +71,9 @@ ramips_board_name() {
 	*"Argus ATP-52B")
 		name="argus-atp52b"
 		;;
+	*"BR6524N")
+		name="br6524n"
+		;;
 	*"Asus WL-330N")
 		name="wl-330n"
 		;;

target/linux/ramips/files/arch/mips/include/asm/mach-ralink/machine.h

@@ -15,6 +15,7 @@ enum ramips_mach_type {
 	RAMIPS_MACH_GENERIC,
 	/* RT2880 based machines */
 	RAMIPS_MACH_F5D8235_V1,		/* Belkin F5D8235 v1 */
+	RAMIPS_MACH_BR6524N,		/* Edimax BR6524N */
 	RAMIPS_MACH_RT_N15,		/* Asus RT-N15 */
 	RAMIPS_MACH_V11ST_FE,		/* Ralink V11ST-FE */
 	RAMIPS_MACH_WLI_TX4_AG300N,	/* Buffalo WLI-TX4-AG300N */

target/linux/ramips/files/arch/mips/ralink/rt288x/Kconfig

@@ -6,6 +6,11 @@ config RT288X_MACH_F5D8235_V1
 	bool "Belkin F5D8235 V1 board support"
 	select RALINK_DEV_GPIO_LEDS
 
+config RT288X_MACH_BR6524N
+	bool "Edimax BR6524N support"
+	select RALINK_DEV_GPIO_BUTTONS
+	select RALINK_DEV_GPIO_LEDS
+
 config RT288X_MACH_RT_N15
 	bool "Asus RT-N15 board support"
 	select RALINK_DEV_GPIO_BUTTONS

target/linux/ramips/files/arch/mips/ralink/rt288x/Makefile

@@ -14,6 +14,7 @@ obj-y	:= irq.o setup.o rt288x.o devices.o clock.o
 obj-$(CONFIG_EARLY_PRINTK)		+= early_printk.o
 
 obj-$(CONFIG_RT288X_MACH_F5D8235_V1)	+= mach-f5d8235-v1.o
+obj-$(CONFIG_RT288X_MACH_BR6524N)	+= mach-br6524n.o
 obj-$(CONFIG_RT288X_MACH_RT_N15)	+= mach-rt-n15.o
 obj-$(CONFIG_RT288X_MACH_V11ST_FE)	+= mach-v11st-fe.o
 obj-$(CONFIG_RT288X_MACH_WLI_TX4_AG300N) += mach-wli-tx4-ag300n.o

target/linux/ramips/files/arch/mips/ralink/rt288x/mach-br6524n.c

@@ -0,0 +1,74 @@
+/*
+ *  Edimax BR6524N board support
+ *
+ *  Copyright (C) 2012 Florian Fainelli <[email protected]>
+ *
+ *  This program is free software; you can redistribute it and/or modify it
+ *  under the terms of the GNU General Public License version 2 as published
+ *  by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/ethtool.h>
+
+#include <asm/mach-ralink/machine.h>
+#include <asm/mach-ralink/dev-gpio-buttons.h>
+#include <asm/mach-ralink/dev-gpio-leds.h>
+#include <asm/mach-ralink/rt288x.h>
+#include <asm/mach-ralink/rt288x_regs.h>
+#include <asm/mach-ralink/ramips_eth_platform.h>
+
+#include "devices.h"
+
+#define BR6524N_GPIO_STATUS_LED	12
+#define BR6524N_GPIO_BUTTON_WPS	0
+
+#define BR6524N_KEYS_POLL_INTERVAL	20
+#define BR6524N_KEYS_DEBOUNCE_INTERVAL	(3 * BR6524N_KEYS_POLL_INTERVAL)
+
+static struct gpio_led br6524n_leds_gpio[] __initdata = {
+	{
+		.name		= "br6524n:green:status",
+		.gpio		= BR6524N_GPIO_STATUS_LED,
+		.active_low	= 1,
+	}
+};
+
+static struct gpio_keys_button br6524n_gpio_buttons[] __initdata = {
+	{
+		.desc		= "wps",
+		.type		= EV_KEY,
+		.code		= KEY_WPS_BUTTON,
+		.debounce_interval = BR6524N_KEYS_DEBOUNCE_INTERVAL,
+		.gpio		= BR6524N_GPIO_BUTTON_WPS,
+	}
+};
+
+static void __init br6524n_fe_init(void)
+{
+	rt288x_gpio_init(RT2880_GPIO_MODE_UART0);
+
+	rt288x_register_flash(0);
+
+	ramips_register_gpio_leds(-1, ARRAY_SIZE(br6524n_leds_gpio),
+				  br6524n_leds_gpio);
+
+	ramips_register_gpio_buttons(-1, BR6524N_KEYS_POLL_INTERVAL,
+				     ARRAY_SIZE(br6524n_gpio_buttons),
+				     br6524n_gpio_buttons);
+
+	rt288x_register_wifi();
+
+	/* Board is connected to an IC+ IP175C Fast Ethernet switch */
+	rt288x_eth_data.speed = SPEED_100;
+	rt288x_eth_data.duplex = DUPLEX_FULL;
+	rt288x_eth_data.tx_fc = 1;
+	rt288x_eth_data.rx_fc = 1;
+	rt288x_eth_data.phy_mask = BIT(0);
+	rt288x_register_ethernet();
+
+	rt288x_register_wdt();
+}
+
+MIPS_MACHINE(RAMIPS_MACH_BR6524N, "BR6524N", "Edimax BR6524N", br6524n_fe_init);

target/linux/ramips/image/Makefile

@@ -259,6 +259,11 @@ define BuildFirmware/Edimax
 	fi
 endef
 
+define BuildFirmware/BR6524N
+	$(call BuildFirmware/Generic,$(1),$(2),$(call mkcmdline,$(3),$(4),$(5)) $(call mkmtd/$(6),$(mtdlayout_4M)),917484,2949120)
+	$(call BuildFirmware/Edimax,$(1),br6524n,CSYS,WNRA,0x50000,0xc00000)
+endef
+
 mtdlayout_f5d8235=320k(u-boot)ro,1536k(kernel),6208k(rootfs),64k(nvram),64k(factory),7744k@0x50000(firmware)
 mtd_f5d8235_kernel_part_size=1572864
 mtd_f5d8235_rootfs_part_size=6356992
@@ -443,6 +448,10 @@ define Image/Build/Profile/F5D8235V1
 	$(call Image/Build/Template/$(fs_squash)/$(1),F5D8235,f5d8235v1,F5D8235_V1)
 endef
 
+define Image/Build/Profile/BR6524N
+	$(call Image/Build/Template/$(fs_squash)/$(1),BR6524N,br6524n,BR6524N,ttyS1,57600,phys)
+endef
+
 define Image/Build/Profile/RTN15
 	$(call Image/Build/Template/$(fs_squash)/$(1),GENERIC_4M,rt-n15,RT-N15,ttyS1,57600,phys)
 endef
@@ -458,6 +467,7 @@ endef
 ifeq ($(CONFIG_RALINK_RT288X),y)
 define Image/Build/Profile/Default
 	$(call Image/Build/Profile/F5D8235V1,$(1))
+	$(call Image/Build/Profile/BR6524N,$(1))
 	$(call Image/Build/Profile/RTN15,$(1))
 	$(call Image/Build/Profile/V11STFE,$(1))
 	$(call Image/Build/Profile/WLITX4AG300N,$(1))

target/linux/ramips/rt288x/config-3.6

@@ -97,6 +97,7 @@ CONFIG_RALINK_RT288X=y
 CONFIG_RAMIPS_WDT=y
 CONFIG_RT288X_MACH_F5D8235_V1=y
 CONFIG_RT288X_MACH_RT_N15=y
+CONFIG_RT288X_MACH_BR6524N=y
 CONFIG_RT288X_MACH_V11ST_FE=y
 CONFIG_RT288X_MACH_WLI_TX4_AG300N=y
 CONFIG_RT288X_MACH_WZR_AGL300NH=y

target/linux/ramips/rt288x/profiles/edimax.mk

@@ -0,0 +1,18 @@
+#
+# Copyright (C) 2011 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+define Profile/BR6524N
+       NAME:=Edimax BR6524N
+       PACKAGES:=kmod-switch-ip17xx kmod-swconfig swconfig
+endef
+
+define Profile/BR6524N/Description
+       Package set for Edimax BR6524N
+endef
+
+$(eval $(call Profile,BR6524N))
+