kirkwood: set sata/usb led trigger for NSA3xx

these two devices have a Sata led for each sata port.
These leds must be controlled separately by a special
sata led trigger already used in oxnas target.

Both these devices have a single USB led, and to keep
consistent behaviour with the Sata leds that show
sata activity, this led uses usb-host trigger
to show usb activity.

Signed-off-by: Alberto Bursi <[email protected]>

target/linux/kirkwood/base-files/etc/board.d/01_leds

@@ -40,9 +40,15 @@ case "$board" in
 	;;
 "nsa310b")
 	ucidef_set_led_default "health" "health" "nsa310:green:sys" "1"
+	ucidef_set_led_usbhost "usb" "USB" "nsa310:green:usb"
+	ucidef_set_led_ataport "hdd" "HDD" "nsa310:green:hdd" "1"
+	ucidef_set_led_ataport "esata" "eSata" "nsa310:green:esata" "2"
 	;;
 "nsa325")
 	ucidef_set_led_default "health" "health" "nsa325:green:sys" "1"
+	ucidef_set_led_usbhost "usb" "USB" "nsa325:green:usb"
+	ucidef_set_led_ataport "hdd1" "HDD1" "nsa325:green:sata1" "1"
+	ucidef_set_led_ataport "hdd2" "HDD2" "nsa325:green:sata2" "2"
 	;;
 "sheevaplug" | \
 "sheevaplug-esata")

target/linux/kirkwood/config-4.4

@@ -26,6 +26,7 @@ CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y
 CONFIG_ARCH_WANT_GENERAL_HUGETLB=y
 CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
+CONFIG_ARCH_WANT_LIBATA_LEDS=y
 CONFIG_ARM=y
 # CONFIG_ARMADA_THERMAL is not set
 CONFIG_ARM_APPENDED_DTB=y
@@ -41,6 +42,7 @@ CONFIG_ARM_PATCH_PHYS_VIRT=y
 # CONFIG_ARM_THUMB is not set
 CONFIG_ATA=y
 CONFIG_ATAGS=y
+CONFIG_ATA_LEDS=y
 CONFIG_AUTO_ZRELADDR=y
 CONFIG_BLK_DEV_SD=y
 CONFIG_CACHE_FEROCEON_L2=y
@@ -306,6 +308,7 @@ CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_HCD_ORION=y
 # CONFIG_USB_EHCI_HCD_PLATFORM is not set
 CONFIG_USB_EHCI_PCI=y
+CONFIG_USB_LED_TRIG=y
 CONFIG_USB_STORAGE=y
 CONFIG_USB_SUPPORT=y
 # CONFIG_USB_UHCI_HCD is not set

target/linux/kirkwood/patches-4.4/210-enable-sata-port-specific-led-triggers.patch

@@ -0,0 +1,10 @@
+--- a/arch/arm/mach-mvebu/Kconfig
++++ b/arch/arm/mach-mvebu/Kconfig
+@@ -105,6 +105,7 @@ config MACH_DOVE
+ config MACH_KIRKWOOD
+ 	bool "Marvell Kirkwood boards" if ARCH_MULTI_V5
+ 	select ARCH_REQUIRE_GPIOLIB
++	select ARCH_WANT_LIBATA_LEDS
+ 	select CPU_FEROCEON
+ 	select KIRKWOOD_CLK
+ 	select MACH_MVEBU_ANY