adm8668: drop 3.14

Signed-off-by: Luka Perkov <[email protected]>

SVN-Revision: 45373

target/linux/adm8668/config-3.14

@@ -1,104 +0,0 @@
-CONFIG_ADM8668=y
-CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE=y
-CONFIG_ARCH_DISCARD_MEMBLOCK=y
-CONFIG_ARCH_HIBERNATION_POSSIBLE=y
-CONFIG_ARCH_REQUIRE_GPIOLIB=y
-CONFIG_ARCH_SUSPEND_POSSIBLE=y
-CONFIG_ARM_AMBA=y
-# CONFIG_ARM_SP805_WATCHDOG is not set
-CONFIG_CEVT_R4K=y
-CONFIG_CEVT_R4K_LIB=y
-CONFIG_CMDLINE="console=ttyS0 earlyprintk"
-CONFIG_CMDLINE_BOOL=y
-CONFIG_CMDLINE_OVERRIDE=y
-CONFIG_CPU_HAS_PREFETCH=y
-CONFIG_CPU_HAS_SYNC=y
-CONFIG_CPU_LITTLE_ENDIAN=y
-CONFIG_CPU_MIPS32=y
-CONFIG_CPU_MIPS32_R1=y
-CONFIG_CPU_MIPSR1=y
-CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
-CONFIG_CPU_SUPPORTS_HIGHMEM=y
-CONFIG_CSRC_R4K=y
-CONFIG_CSRC_R4K_LIB=y
-# CONFIG_DE2104X is not set
-# CONFIG_DE4X5 is not set
-CONFIG_DECOMPRESS_LZMA=y
-# CONFIG_DM9102 is not set
-CONFIG_DMA_NONCOHERENT=y
-CONFIG_EARLY_PRINTK=y
-CONFIG_GENERIC_ATOMIC64=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
-CONFIG_GENERIC_CMOS_UPDATE=y
-CONFIG_GENERIC_GPIO=y
-CONFIG_GENERIC_IRQ_SHOW=y
-CONFIG_GENERIC_PCI_IOMAP=y
-CONFIG_GPIOLIB=y
-CONFIG_GPIO_SYSFS=y
-CONFIG_HARDWARE_WATCHPOINTS=y
-CONFIG_HAS_DMA=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT=y
-CONFIG_HAVE_ARCH_JUMP_LABEL=y
-CONFIG_HAVE_ARCH_KGDB=y
-CONFIG_HAVE_C_RECORDMCOUNT=y
-CONFIG_HAVE_DMA_API_DEBUG=y
-CONFIG_HAVE_DMA_ATTRS=y
-CONFIG_HAVE_DYNAMIC_FTRACE=y
-CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
-CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
-CONFIG_HAVE_FUNCTION_TRACER=y
-CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
-CONFIG_HAVE_GENERIC_DMA_COHERENT=y
-CONFIG_HAVE_GENERIC_HARDIRQS=y
-CONFIG_HAVE_IDE=y
-CONFIG_HAVE_IRQ_WORK=y
-CONFIG_HAVE_MEMBLOCK=y
-CONFIG_HAVE_MEMBLOCK_NODE_MAP=y
-CONFIG_HAVE_OPROFILE=y
-CONFIG_HAVE_PERF_EVENTS=y
-CONFIG_HW_HAS_PCI=y
-CONFIG_INITRAMFS_SOURCE=""
-CONFIG_IRQ_CPU=y
-CONFIG_IRQ_FORCED_THREADING=y
-CONFIG_MIPS=y
-CONFIG_MIPS_L1_CACHE_SHIFT=5
-# CONFIG_MIPS_MACHINE is not set
-CONFIG_MIPS_MT_DISABLED=y
-CONFIG_MTD_ADM8668_NOR=y
-CONFIG_NEED_DMA_MAP_STATE=y
-CONFIG_NEED_PER_CPU_KM=y
-CONFIG_NET_TULIP=y
-CONFIG_NO_EXCEPT_FILL=y
-CONFIG_NO_GENERIC_PCI_IOPORT_MAP=y
-CONFIG_PAGEFLAGS_EXTENDED=y
-CONFIG_PCI=y
-CONFIG_PCI_DOMAINS=y
-CONFIG_PERF_USE_VMALLOC=y
-# CONFIG_PREEMPT_RCU is not set
-# CONFIG_SCSI_DMA is not set
-# CONFIG_SERIAL_8250 is not set
-CONFIG_SERIAL_AMBA_PL010=y
-CONFIG_SERIAL_AMBA_PL010_CONSOLE=y
-CONFIG_SERIAL_AMBA_PL010_NUMPORTS=2
-CONFIG_SERIAL_AMBA_PL010_PORTNAME="ttyS"
-# CONFIG_SERIAL_AMBA_PL011 is not set
-CONFIG_SWAP_IO_SPACE=y
-CONFIG_SYS_HAS_CPU_MIPS32_R1=y
-CONFIG_SYS_HAS_EARLY_PRINTK=y
-CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
-CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
-CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y
-CONFIG_TULIP=y
-CONFIG_TULIP_NAPI=y
-# CONFIG_TULIP_NAPI_HW_MITIGATION is not set
-# CONFIG_TULIP_PCI is not set
-CONFIG_TULIP_PLATFORM=y
-# CONFIG_ULI526X is not set
-CONFIG_USB_ARCH_HAS_XHCI=y
-# CONFIG_USB_HCD_BCMA is not set
-# CONFIG_USB_HCD_SSB is not set
-CONFIG_USB_SUPPORT=y
-# CONFIG_WINBOND_840 is not set
-CONFIG_ZONE_DMA_FLAG=0

target/linux/adm8668/files-3.14/arch/mips/adm8668/Kconfig

@@ -1,2 +0,0 @@
-config ARM_AMBA
-	def_bool y

target/linux/adm8668/files-3.14/arch/mips/adm8668/Makefile

@@ -1,6 +0,0 @@
-#
-# something witty  --neutronscott
-#
-
-obj-y	 	:= irq.o prom.o platform.o gpio.o \
-		   setup.o clock.o time.o early_printk.o \

target/linux/adm8668/files-3.14/arch/mips/adm8668/Platform

@@ -1,6 +0,0 @@
-#
-# Infineon ADM8668 WildPass
-#
-platform-$(CONFIG_ADM8668)	+= adm8668/
-cflags-$(CONFIG_ADM8668)	+= -I$(srctree)/arch/mips/include/asm/mach-adm8668
-load-$(CONFIG_ADM8668)		+= 0xffffffff80002000

target/linux/adm8668/files-3.14/arch/mips/adm8668/clock.c

@@ -1,76 +0,0 @@
-/*
- * ADM8668 minimal clock support
- *
- * Copyright (C) 2012, Florian Fainelli <[email protected]>
- *
- * Licensed under the terms of the GPLv2
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/device.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-
-#include <adm8668.h>
-
-struct clk {
-	unsigned long rate;
-};
-
-static struct clk uart_clk = {
-	.rate	= 62500000,
-};
-
-static struct clk sys_clk;
-
-struct clk *clk_get(struct device *dev, const char *id)
-{
-	const char *lookup = id;
-
-	if (dev)
-		lookup = dev_name(dev);
-
-	if (!strcmp(lookup, "apb:uart0"))
-		return &uart_clk;
-	if (!strcmp(lookup, "sys"))
-		return &sys_clk;
-
-	return ERR_PTR(-ENOENT);
-}
-EXPORT_SYMBOL(clk_get);
-
-int clk_enable(struct clk *clk)
-{
-	return 0;
-}
-EXPORT_SYMBOL(clk_enable);
-
-void clk_disable(struct clk *clk)
-{
-}
-EXPORT_SYMBOL(clk_disable);
-
-unsigned long clk_get_rate(struct clk *clk)
-{
-	return clk->rate;
-}
-EXPORT_SYMBOL(clk_get_rate);
-
-void clk_put(struct clk *clk)
-{
-}
-EXPORT_SYMBOL(clk_put);
-
-void __init adm8668_init_clocks(void)
-{
-	u32 adj;
-
-	/* adjustable clock selection
-	 * CR3 bit 14~11, 0000 -> 175MHz, 0001 -> 180MHz, etc...
-	 */
-	adj = (ADM8668_CONFIG_REG(ADM8668_CR3) >> 11) & 0xf;
-	sys_clk.rate = 175000000 + (adj * 5000000);
-
-	pr_info("ADM8668 CPU clock: %lu MHz\n", sys_clk.rate / 1000000);
-}

target/linux/adm8668/files-3.14/arch/mips/adm8668/early_printk.c

@@ -1,16 +0,0 @@
-#include <linux/io.h>
-#include <linux/amba/serial.h>
-#include <adm8668.h>
-
-#define UART_READ(r) \
-	__raw_readl((void __iomem *)(KSEG1ADDR(ADM8668_UART0_BASE) + (r)))
-
-#define UART_WRITE(v, r) \
-	__raw_writel((v), (void __iomem *)(KSEG1ADDR(ADM8668_UART0_BASE) + (r)))
-
-void prom_putchar(char c)
-{
-	UART_WRITE(c, UART01x_DR);
-	while ((UART_READ(UART01x_FR) & UART01x_FR_TXFF) != 0)
-		;
-}

target/linux/adm8668/files-3.14/arch/mips/adm8668/gpio.c

@@ -1,123 +0,0 @@
-/*
- * Infineon/ADMTek ADM8668 WildPass GPIO support
- *
- * Copyright (C) 2012 Florian Fainelli <[email protected]>
- *
- * Licensed under the terms of GPLv2.
- *
- */
-#include <linux/kernel.h>
-#include <linux/gpio.h>
-#include <linux/io.h>
-
-#include <adm8668.h>
-
-#define GPIO_MASK	0x3f
-
-#define GPIO_IN_OFS	0
-#define GPIO_OUT_OFS	6
-#define GPIO_OE_OFS	12
-
-struct adm8668_gpio_chip {
-	void __iomem	*base;
-	struct gpio_chip chip;
-};
-
-static int adm8668_gpio_dir_out(struct gpio_chip *chip,
-				unsigned offset, int value)
-{
-	struct adm8668_gpio_chip *c =
-		container_of(chip, struct adm8668_gpio_chip, chip);
-	u32 mask;
-
-	/* clear input, set output enable and output value */
-	mask = __raw_readl(c->base);
-	mask &= ~(1 << offset);
-	mask |= (1 << (offset + GPIO_OE_OFS));
-	if (value)
-		mask |= (1 << (offset + GPIO_OUT_OFS));
-	else
-		mask &= ~(1 << (offset + GPIO_OUT_OFS));
-	__raw_writel(mask, c->base);
-
-	return 0;
-}
-
-static int adm8668_gpio_dir_in(struct gpio_chip *chip,
-				unsigned offset)
-{
-	struct adm8668_gpio_chip *c =
-		container_of(chip, struct adm8668_gpio_chip, chip);
-	u32 mask;
-
-	mask = __raw_readl(c->base);
-	mask &= ~(((1 << (offset + GPIO_OE_OFS)) | (1 << (offset + GPIO_OUT_OFS))));
-	mask |= (1 << offset);
-	__raw_writel(mask, c->base);
-
-	return 0;
-}
-
-static void adm8668_gpio_set(struct gpio_chip *chip,
-				unsigned offset, int value)
-{
-	struct adm8668_gpio_chip *c =
-		container_of(chip, struct adm8668_gpio_chip, chip);
-	u32 mask;
-
-	mask = __raw_readl(c->base);
-	if (value)
-		mask |= (1 << (offset + GPIO_OUT_OFS));
-	else
-		mask &= ~(1 << (offset + GPIO_OUT_OFS));
-	__raw_writel(mask, c->base);
-}
-
-static int adm8668_gpio_get(struct gpio_chip *chip,
-				unsigned offset)
-{
-	struct adm8668_gpio_chip *c =
-		container_of(chip, struct adm8668_gpio_chip, chip);
-	u32 value;
-
-	value = __raw_readl(c->base) & GPIO_MASK;
-
-	return value & (1 << offset);
-}
-
-static struct adm8668_gpio_chip adm8668_gpio_cpu = {
-	.base = (void __iomem *)KSEG1ADDR(ADM8668_CONFIG_BASE + CRGPIO_REG),
-	.chip = {
-		.label			= "adm8668-cpu-gpio",
-		.direction_output	= adm8668_gpio_dir_out,
-		.direction_input	= adm8668_gpio_dir_in,
-		.set			= adm8668_gpio_set,
-		.get			= adm8668_gpio_get,
-		.ngpio			= 6,
-	},
-};
-
-static struct adm8668_gpio_chip adm8668_gpio_wlan = {
-	.base = (void __iomem *)KSEG1ADDR(ADM8668_WLAN_BASE + GPIO_REG),
-	.chip = {
-		.label			= "adm8668-wlan-gpio",
-		.direction_output	= adm8668_gpio_dir_out,
-		.direction_input	= adm8668_gpio_dir_in,
-		.set			= adm8668_gpio_set,
-		.get			= adm8668_gpio_get,
-		.ngpio			= 6,
-		.base			= 6,
-	},
-};
-
-static int __init adm8668_gpio_init(void)
-{
-	int ret;
-
-	ret = gpiochip_add(&adm8668_gpio_cpu.chip);
-	if (ret)
-		return ret;
-
-	return gpiochip_add(&adm8668_gpio_wlan.chip);
-}
-arch_initcall(adm8668_gpio_init);

target/linux/adm8668/files-3.14/arch/mips/adm8668/irq.c

@@ -1,126 +0,0 @@
-/*
- * Copyright (C) 2010 Scott Nicholas <[email protected]>
- * Copyright (C) 2012 Florian Fainelli <[email protected]>
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file "COPYING" in the main directory of this archive
- * for more details.
- */
-
-#include <linux/init.h>
-#include <linux/kernel_stat.h>
-#include <linux/signal.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/slab.h>
-#include <linux/random.h>
-#include <linux/pm.h>
-#include <linux/irq.h>
-#include <asm/mipsregs.h>
-#include <asm/irq_cpu.h>
-#include <asm/irq.h>
-#include <adm8668.h>
-
-/* interrupt controller */
-#define IRQ_STATUS_REG		0x00	/* Read */
-#define IRQ_ENABLE_REG		0x08	/* Read/Write */
-#define IRQ_DISABLE_REG		0x0C	/* Write */
-
-#define IRQ_MASK		0xffff
-
-static inline void intc_write_reg(u32 val, unsigned int reg)
-{
-	void __iomem *base = (void __iomem *)KSEG1ADDR(ADM8668_INTC_BASE);
-
-	__raw_writel(val, base + reg);
-}
-
-static inline u32 intc_read_reg(unsigned int reg)
-{
-	void __iomem *base = (void __iomem *)KSEG1ADDR(ADM8668_INTC_BASE);
-
-	return __raw_readl(base + reg);
-}
-
-static void adm8668_irq_cascade(void)
-{
-	int irq;
-	u32 intsrc;
-
-	intsrc = intc_read_reg(IRQ_STATUS_REG) & IRQ_MASK;
-	if (intsrc) {
-		irq = fls(intsrc) - 1;
-		do_IRQ(irq);
-	} else
-		spurious_interrupt();
-}
-
-/*
- * System irq dispatch
- */
-void plat_irq_dispatch(void)
-{
-	unsigned int pending;
-
-	pending = read_c0_cause() & read_c0_status() & ST0_IM;
-
-	/* timer interrupt, that we renumbered */
-	if (pending & STATUSF_IP7)
-		do_IRQ(MIPS_CPU_IRQ_BASE + 7);
-	else if (pending & STATUSF_IP2)
-		adm8668_irq_cascade();
-	else
-		spurious_interrupt();
-}
-
-/*
- * enable 8668 irq
- */
-static void enable_adm8668_irq(struct irq_data *d)
-{
-	intc_write_reg((1 << d->irq), IRQ_ENABLE_REG);
-}
-
-
-static void ack_adm8668_irq(struct irq_data *d)
-{
-	intc_write_reg((1 << d->irq), IRQ_DISABLE_REG);
-}
-
-/*
- * system irq type
- */
-
-static struct irq_chip adm8668_irq_type = {
-	.name = "adm8668",
-	.irq_ack = ack_adm8668_irq,
-	.irq_mask = ack_adm8668_irq,
-	.irq_unmask = enable_adm8668_irq
-};
-
-/*
- * irq init
- */
-static void __init init_adm8668_irqs(void)
-{
-	int i;
-
-	/* disable all interrupts for the moment */
-	intc_write_reg(IRQ_MASK, IRQ_DISABLE_REG);
-
-	for (i = 0; i <= ADM8668_IRQ_MAX; i++)
-		irq_set_chip_and_handler(i, &adm8668_irq_type,
-			handle_level_irq);
-
-	/* hw0 is where our interrupts are uh.. interrupted at. */
-	set_c0_status(IE_IRQ0);
-}
-
-/*
- * system init
- */
-void __init arch_init_irq(void)
-{
-	mips_cpu_irq_init();
-	init_adm8668_irqs();
-}

target/linux/adm8668/files-3.14/arch/mips/adm8668/platform.c

@@ -1,196 +0,0 @@
-/*
- * Copyright (C) 2010 Scott Nicholas <[email protected]>
- * Copyright (C) 2012 Florian Fainelli <[email protected]>
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file "COPYING" in the main directory of this archive
- * for more details.
- */
-
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/platform_device.h>
-#include <linux/platform_data/tulip.h>
-#include <linux/usb/ehci_pdriver.h>
-#include <linux/mtd/physmap.h>
-#include <linux/pci.h>
-#include <linux/slab.h>
-#include <linux/ioport.h>
-#include <linux/amba/bus.h>
-#include <linux/amba/serial.h>
-
-#include <asm/reboot.h>
-#include <asm/time.h>
-#include <asm/addrspace.h>
-#include <asm/bootinfo.h>
-#include <asm/io.h>
-#include <adm8668.h>
-
-#define ADM8868_UBOOT_ENV		0x20000
-#define ADM8868_UBOOT_WAN_MAC		0x5ac
-#define ADM8868_UBOOT_LAN_MAC		0x404
-
-static void adm8668_uart_set_mctrl(struct amba_device *dev,
-					void __iomem *base,
-					unsigned int mcrtl)
-{
-}
-
-static struct amba_pl010_data adm8668_uart0_data = {
-	.set_mctrl = adm8668_uart_set_mctrl,
-};
-
-static struct amba_device adm8668_uart0_device = {
-	.dev = {
-		.init_name	= "apb:uart0",
-		.platform_data	= &adm8668_uart0_data,
-	},
-	.res = {
-		.start		= ADM8668_UART0_BASE,
-		.end		= ADM8668_UART0_BASE + 0xF,
-		.flags		= IORESOURCE_MEM,
-	},
-	.irq = {
-		ADM8668_UART0_IRQ,
-		-1
-	},
-	.periphid = 0x0041010,
-};
-
-static struct resource eth0_resources[] = {
-	{
-		.start		= ADM8668_LAN_BASE,
-		.end		= ADM8668_LAN_BASE + 256,
-		.flags		= IORESOURCE_MEM,
-	},
-	{
-		.start		= ADM8668_LAN_IRQ,
-		.flags		= IORESOURCE_IRQ,
-	},
-};
-
-static struct tulip_platform_data eth0_pdata = {
-	.chip_id	= ADM8668,
-};
-
-static struct platform_device adm8668_eth0_device = {
-	.name		= "tulip",
-	.id		= 0,
-	.resource	= eth0_resources,
-	.num_resources	= ARRAY_SIZE(eth0_resources),
-	.dev.platform_data = &eth0_pdata,
-};
-
-static struct resource eth1_resources[] = {
-	{
-		.start		= ADM8668_WAN_BASE,
-		.end		= ADM8668_WAN_BASE + 256,
-		.flags		= IORESOURCE_MEM,
-	},
-	{
-		.start		= ADM8668_WAN_IRQ,
-		.flags		= IORESOURCE_IRQ,
-	},
-};
-
-static struct tulip_platform_data eth1_pdata = {
-	.chip_id	= ADM8668,
-};
-
-static struct platform_device adm8668_eth1_device = {
-	.name		= "tulip",
-	.id		= 1,
-	.resource	= eth1_resources,
-	.num_resources	= ARRAY_SIZE(eth1_resources),
-	.dev.platform_data = &eth1_pdata,
-};
-
-static struct resource usb_resources[] = {
-	{
-		.start	= ADM8668_USB_BASE,
-		.end	= ADM8668_USB_BASE + 0x1FFFFF,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.start	= ADM8668_USB_IRQ,
-		.end	= ADM8668_USB_IRQ,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct usb_ehci_pdata usb_pdata = {
-	.caps_offset	= 0x100,
-	.has_tt		= 1,
-};
-
-static struct platform_device adm8668_usb_device = {
-	.name		= "ehci-platform",
-	.id		= -1,
-	.resource	= usb_resources,
-	.num_resources	= ARRAY_SIZE(usb_resources),
-	.dev.platform_data = &usb_pdata,
-};
-
-static struct platform_device *adm8668_devs[] = {
-	&adm8668_eth0_device,
-	&adm8668_eth1_device,
-	&adm8668_usb_device,
-};
-
-static void adm8668_fetch_mac(int unit)
-{
-	u8 *mac;
-	u32 offset;
-	struct tulip_platform_data *pdata;
-
-	switch (unit) {
-	case -1:
-	case 0:
-		offset = ADM8868_UBOOT_LAN_MAC;
-		pdata = &eth0_pdata;
-		break;
-	case 1:
-		offset = ADM8868_UBOOT_WAN_MAC;
-		pdata = &eth1_pdata;
-		break;
-	default:
-		pr_err("unsupported ethernet unit: %d\n", unit);
-		return;
-	}
-
-	mac = (u8 *)(KSEG1ADDR(ADM8668_SMEM1_BASE) + ADM8868_UBOOT_ENV + offset);
-
-	memcpy(pdata->mac, mac, sizeof(pdata->mac));
-}
-
-static void adm8668_ehci_workaround(void)
-{
-	u32 chipid;
-
-	chipid = ADM8668_CONFIG_REG(ADM8668_CR0);
-	ADM8668_CONFIG_REG(ADM8668_CR66) = 0x0C1600D9;
-
-	if (chipid == 0x86880001)
-		return;
-
-	ADM8668_CONFIG_REG(ADM8668_CR66) &= ~(3 << 20);
-	ADM8668_CONFIG_REG(ADM8668_CR66) |= (1 << 20);
-	pr_info("ADM8668: applied USB workaround\n");
-}
-
-
-int __init adm8668_devs_register(void)
-{
-	int ret;
-
-	ret = amba_device_register(&adm8668_uart0_device, &iomem_resource);
-	if (ret)
-		panic("failed to register AMBA UART");
-
-	adm8668_fetch_mac(0);
-	adm8668_fetch_mac(1);
-	adm8668_ehci_workaround();
-
-	return platform_add_devices(adm8668_devs, ARRAY_SIZE(adm8668_devs));
-}
-arch_initcall(adm8668_devs_register);

target/linux/adm8668/files-3.14/arch/mips/adm8668/prom.c

@@ -1,95 +0,0 @@
-/*
- * Copyright (C) 2010 Scott Nicholas <[email protected]>
- *
- * based on work of rb532 prom.c
- *  Copyright (C) 2003, Peter Sadik <[email protected]>
- *  Copyright (C) 2005-2006, P.Christeas <[email protected]>
- *  Copyright (C) 2007, Gabor Juhos <[email protected]>
- *			Felix Fietkau <[email protected]>
- *			Florian Fainelli <[email protected]>
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file "COPYING" in the main directory of this archive
- * for more details.
- */
-
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/console.h>
-#include <linux/string.h>
-#include <linux/serial_core.h>
-#include <asm/bootinfo.h>
-#include <adm8668.h>
-#include "u-boot.h"
-
-register volatile struct global_data *gd asm ("k0");
-
-void __init prom_free_prom_memory(void)
-{
-	/* No prom memory to free */
-}
-
-static inline int match_tag(char *arg, const char *tag)
-{
-	return strncmp(arg, tag, strlen(tag)) == 0;
-}
-
-static inline unsigned long tag2ul(char *arg, const char *tag)
-{
-	char *num;
-
-	num = arg + strlen(tag);
-	return simple_strtoul(num, 0, 10);
-}
-
-void __init prom_setup_cmdline(void)
-{
-	char *cp;
-	int prom_argc;
-	char **prom_argv;
-	int i;
-
-	prom_argc = fw_arg0;
-	prom_argv = (char **)KSEG0ADDR(fw_arg1);
-
-	cp = &(arcs_cmdline[0]);
-	for (i = 1; i < prom_argc; i++) {
-		prom_argv[i] = (char *)KSEG0ADDR(prom_argv[i]);
-
-		/* default bootargs has "console=/dev/ttyS0" yet console won't
-		 * show up at all if you include the '/dev/' nowadays ... */
-		if (match_tag(prom_argv[i], "console=/dev/")) {
-			char *ptr = prom_argv[i] + strlen("console=/dev/");
-
-			strcpy(cp, "console=");
-			cp += strlen("console=");
-			strcpy(cp, ptr);
-			cp += strlen(ptr);
-			*cp++ = ' ';
-			continue;
-		}
-		strcpy(cp, prom_argv[i]);
-		cp += strlen(prom_argv[i]);
-		*cp++ = ' ';
-	}
-	if (prom_argc > 1)
-		--cp; /* trailing space */
-
-	*cp = '\0';
-}
-
-void __init prom_init(void)
-{
-	bd_t *bd = gd->bd;
-	int memsize;
-
-	memsize = bd->bi_memsize;
-	printk("Board info:\n");
-	printk("  RAM size: %d MB\n", (int)memsize/(1024*1024));
-	printk("  NOR start: %#lx\n", bd->bi_flashstart);
-	printk("  NOR size: %#lx\n", bd->bi_flashsize);
-
-	prom_setup_cmdline();
-	add_memory_region(0, memsize, BOOT_MEM_RAM);
-}

target/linux/adm8668/files-3.14/arch/mips/adm8668/setup.c

@@ -1,36 +0,0 @@
-#include <linux/init.h>
-#include <linux/reboot.h>
-
-#include <asm/reboot.h>
-#include <adm8668.h>
-
-static void adm8668_restart(char *cmd)
-{
-	int i;
-
-	/* the real deal */
-	for (i = 0; i < 1000; i++)
-		;
-	ADM8668_CONFIG_REG(ADM8668_CR1) = 1;
-}
-
-void __init plat_mem_setup(void)
-{
-	_machine_restart = adm8668_restart;
-}
-
-const char *get_system_type(void)
-{
-        unsigned long chipid = ADM8668_CONFIG_REG(ADM8668_CR0);
-        int product, revision;
-	static char ret[32];
-
-        product = chipid >> 16;
-        revision = chipid & 0xffff;
-
-	/* i getting fancy :\ */
-	snprintf(ret, sizeof(ret), "ADM%xr%x", product, revision);
-
-	return ret;
-}
-

target/linux/adm8668/files-3.14/arch/mips/adm8668/time.c

@@ -1,20 +0,0 @@
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/clk.h>
-
-#include <asm/time.h>
-#include <adm8668.h>
-
-void __init plat_time_init(void)
-{
-	struct clk *sys_clk;
-
-	adm8668_init_clocks();
-
-	sys_clk = clk_get(NULL, "sys");
-	if (IS_ERR(sys_clk))
-		panic("unable to get system clock\n");
-
-	mips_hpt_frequency = clk_get_rate(sys_clk) / 2;
-}
-

target/linux/adm8668/files-3.14/arch/mips/adm8668/u-boot.h

@@ -1,52 +0,0 @@
-/*
- * (C) Copyright 2003
- * Wolfgang Denk, DENX Software Engineering, <[email protected]>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#ifndef _U_BOOT_H_
-#define _U_BOOT_H_	1
-
-typedef struct bd_info {
-	int		bi_baudrate;	/* serial console baudrate */
-	unsigned long	bi_ip_addr;	/* IP Address */
-	unsigned char	bi_enetaddr[6];	/* Ethernet adress */
-	unsigned long	bi_arch_number;	/* unique id for this board */
-	unsigned long	bi_boot_params;	/* where this board expects params */
-	unsigned long	bi_memstart;	/* start of DRAM memory */
-	unsigned long	bi_memsize;	/* size	 of DRAM memory in bytes */
-	unsigned long	bi_flashstart;	/* start of FLASH memory */
-	unsigned long	bi_flashsize;	/* size  of FLASH memory */
-	unsigned long	bi_flashoffset;	/* reserved area for startup monitor */
-} bd_t;
-
-struct global_data {
-	bd_t		*bd;            /* board data... */
-	unsigned long	flags;
-	unsigned long	baudrate;
-	unsigned long	have_console;   /* serial_init() was called */
-	unsigned long	ram_size;       /* RAM size */
-	unsigned long	reloc_off;      /* Relocation Offset */
-	unsigned long	env_addr;       /* Address  of Environment struct */
-	unsigned long	env_valid;      /* Checksum of Environment valid? */
-	void		**jt;           /* jump table */
-};
-
-#endif	/* _U_BOOT_H_ */

target/linux/adm8668/files-3.14/arch/mips/include/asm/mach-adm8668/adm8668.h

@@ -1,69 +0,0 @@
-/************************************************************************
- *
- *    Copyright (c) 2005
- *    Infineon Technologies AG
- *    St. Martin Strasse 53; 81669 Muenchen; Germany
- *
- ************************************************************************/
-
-#ifndef  __ADM8668_H__
-#define  __ADM8668_H__
-
-/*=======================  Physical Memory Map  ============================*/
-#define ADM8668_SDRAM_BASE	0
-#define ADM8668_SMEM1_BASE	0x10000000
-#define ADM8668_MPMC_BASE	0x11000000
-#define ADM8668_USB_BASE	0x11200000
-#define ADM8668_CONFIG_BASE	0x11400000
-#define ADM8668_WAN_BASE	0x11600000
-#define ADM8668_WLAN_BASE	0x11800000
-#define ADM8668_LAN_BASE	0x11A00000
-#define ADM8668_INTC_BASE	0x1E000000
-#define ADM8668_TMR_BASE	0x1E200000
-#define ADM8668_UART0_BASE	0x1E400000
-#define ADM8668_SMEM0_BASE	0x1FC00000
-#define ADM8668_NAND_BASE	0x1FFFFF00
-
-#define ADM8668_PCICFG_BASE	0x12200000
-#define ADM8668_PCIDAT_BASE	0x12400000
-
-/* interrupt levels */
-#define ADM8668_SWI_IRQ		1
-#define ADM8668_COMMS_RX_IRQ	2
-#define ADM8668_COMMS_TX_IRQ	3
-#define ADM8668_TIMER0_IRQ	4
-#define ADM8668_TIMER1_IRQ	5
-#define ADM8668_UART0_IRQ	6
-#define ADM8668_LAN_IRQ		7
-#define ADM8668_WAN_IRQ		8
-#define ADM8668_WLAN_IRQ	9
-#define ADM8668_GPIO_IRQ	10
-#define ADM8668_IDE_IRQ		11
-#define ADM8668_PCI2_IRQ	12
-#define ADM8668_PCI1_IRQ	13
-#define ADM8668_PCI0_IRQ	14
-#define ADM8668_USB_IRQ		15
-#define ADM8668_IRQ_MAX		ADM8668_USB_IRQ
-
-/* register access macros */
-#define ADM8668_CONFIG_REG(_reg)	\
-	(*((volatile unsigned int *)(KSEG1ADDR(ADM8668_CONFIG_BASE + (_reg)))))
-
-/* lan registers */
-#define	NETCSR6			0x30
-#define	NETCSR7			0x38
-#define	NETCSR37		0xF8
-
-/* known/used CPU configuration registers */
-#define ADM8668_CR0		0x00
-#define ADM8668_CR1		0x04
-#define ADM8668_CR3		0x0C
-#define ADM8668_CR66		0x108
-
-/** For GPIO control **/
-#define	GPIO_REG		0x5C	/* on WLAN */
-#define CRGPIO_REG		0x20	/* on CPU */
-
-void adm8668_init_clocks(void);
-
-#endif /* __ADM8668_H__ */

target/linux/adm8668/files-3.14/arch/mips/include/asm/mach-adm8668/asm/sizes.h

@@ -1,56 +0,0 @@
-/*
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-/* DO NOT EDIT!! - this file automatically generated
- *                 from .s file by awk -f s2h.awk
- */
-/*  Size definitions
- *  Copyright (C) ARM Limited 1998. All rights reserved.
- */
-
-#ifndef __sizes_h
-#define __sizes_h                       1
-
-/* handy sizes */
-#define SZ_16				0x00000010
-#define SZ_256				0x00000100
-#define SZ_512				0x00000200
-
-#define SZ_1K                           0x00000400
-#define SZ_4K                           0x00001000
-#define SZ_8K                           0x00002000
-#define SZ_16K                          0x00004000
-#define SZ_64K                          0x00010000
-#define SZ_128K                         0x00020000
-#define SZ_256K                         0x00040000
-#define SZ_512K                         0x00080000
-
-#define SZ_1M                           0x00100000
-#define SZ_2M                           0x00200000
-#define SZ_4M                           0x00400000
-#define SZ_8M                           0x00800000
-#define SZ_16M                          0x01000000
-#define SZ_32M                          0x02000000
-#define SZ_64M                          0x04000000
-#define SZ_128M                         0x08000000
-#define SZ_256M                         0x10000000
-#define SZ_512M                         0x20000000
-
-#define SZ_1G                           0x40000000
-#define SZ_2G                           0x80000000
-
-#endif
-
-/*         END */

target/linux/adm8668/files-3.14/arch/mips/include/asm/mach-adm8668/gpio.h

@@ -1,13 +0,0 @@
-#ifndef __ADM8668_GPIO_H__
-#define __ADM8668_GPIO_H__
-
-#define gpio_to_irq(gpio)       -1
-
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-
-#define gpio_cansleep __gpio_cansleep
-
-#include <asm-generic/gpio.h>
-
-#endif

target/linux/adm8668/files-3.14/arch/mips/include/asm/mach-adm8668/irq.h

@@ -1,14 +0,0 @@
-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 2003 by Ralf Baechle
- */
-#ifndef __ASM_MACH_ADM8668_IRQ_H
-#define __ASM_MACH_ADM8668_IRQ_H
-
-#define	NR_IRQS			32
-#define	MIPS_CPU_IRQ_BASE	16
-
-#endif /* __ASM_MACH_ADM8668_IRQ_H */

target/linux/adm8668/files-3.14/arch/mips/include/asm/mach-adm8668/war.h

@@ -1,25 +0,0 @@
-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 2002, 2004, 2007 by Ralf Baechle <[email protected]>
- */
-#ifndef __ASM_MIPS_MACH_ADM8668_WAR_H
-#define __ASM_MIPS_MACH_ADM8668_WAR_H
-
-#define R4600_V1_INDEX_ICACHEOP_WAR	0
-#define R4600_V1_HIT_CACHEOP_WAR	0
-#define R4600_V2_HIT_CACHEOP_WAR	0
-#define R5432_CP0_INTERRUPT_WAR		0
-#define BCM1250_M3_WAR			0
-#define SIBYTE_1956_WAR			0
-#define MIPS4K_ICACHE_REFILL_WAR	0
-#define MIPS_CACHE_SYNC_WAR		0
-#define TX49XX_ICACHE_INDEX_INV_WAR	0
-#define RM9000_CDEX_SMP_WAR		0
-#define ICACHE_REFILLS_WORKAROUND_WAR	0
-#define R10000_LLSC_WAR			0
-#define MIPS34K_MISSED_ITLB_WAR		0
-
-#endif /* __ASM_MIPS_MACH_ADM8668_WAR_H */

target/linux/adm8668/files-3.14/arch/mips/pci/pci-adm8668.c

@@ -1,200 +0,0 @@
-/*
- * Copyright (C) 2010 Scott Nicholas <[email protected]>
- * Copyright (C) 2012 Florian Fainelli <[email protected]>
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Note that this controller is identical to the ADM5120 one
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/pci.h>
-#include <linux/types.h>
-#include <linux/spinlock.h>
-
-#include <asm/byteorder.h>
-#include <asm/pci.h>
-#include <adm8668.h>
-
-static DEFINE_SPINLOCK(pci_lock);
-
-#define PCI_ENABLE			0x80000000
-#define	ADMPCI_IO_BASE			0x12600000
-#define	ADMPCI_IO_SIZE			0x1fffff
-#define	ADMPCI_MEM_BASE			0x16000000
-#define	ADMPCI_MEM_SIZE			0x7ffffff
-
-static inline void write_cfgaddr(u32 addr)
-{
-	__raw_writel((addr | PCI_ENABLE),
-			(void __iomem *)KSEG1ADDR(ADM8668_PCICFG_BASE));
-}
-
-static inline void write_cfgdata(u32 data)
-{
-	__raw_writel(data, (void __iomem *)KSEG1ADDR(ADM8668_PCIDAT_BASE));
-}
-
-static inline u32 read_cfgdata(void)
-{
-	return __raw_readl((void __iomem *)KSEG1ADDR(ADM8668_PCIDAT_BASE));
-}
-
-static inline u32 mkaddr(struct pci_bus *bus, unsigned int devfn, int where)
-{
-	return ((bus->number & 0xff) << 16) | ((devfn & 0xff) << 8) |
-		(where & 0xfc);
-}
-
-static int pci_read_config(struct pci_bus *bus, unsigned int devfn,
-				int where, int size, u32 *val)
-{
-	unsigned long flags;
-	u32 data;
-
-	spin_lock_irqsave(&pci_lock, flags);
-	write_cfgaddr(mkaddr(bus, devfn, where));
-	data = read_cfgdata();
-
-	switch (size) {
-	case 1:
-		if (where & 1)
-			data >>= 8;
-		if (where & 2)
-			data >>= 16;
-		data &= 0xff;
-		break;
-	case 2:
-		if (where & 2)
-			data >>= 16;
-		data &= 0xffff;
-		break;
-	}
-
-	*val = data;
-
-	spin_unlock_irqrestore(&pci_lock, flags);
-
-	return PCIBIOS_SUCCESSFUL;
-}
-
-static int pci_write_config(struct pci_bus *bus, unsigned int devfn,
-				int where, int size, u32 val)
-{
-	unsigned long flags;
-	u32 data;
-	int s;
-
-	spin_lock_irqsave(&pci_lock, flags);
-
-	write_cfgaddr(mkaddr(bus, devfn, where));
-	data = read_cfgdata();
-
-	switch (size) {
-	case 1:
-		s = ((where & 3) << 3);
-		data &= ~(0xff << s);
-		data |= ((val & 0xff) << s);
-		break;
-	case 2:
-		s = ((where & 2) << 4);
-		data &= ~(0xffff << s);
-		data |= ((val & 0xffff) << s);
-		break;
-	case 4:
-		data = val;
-		break;
-	}
-
-	write_cfgdata(data);
-
-	spin_unlock_irqrestore(&pci_lock, flags);
-
-	return PCIBIOS_SUCCESSFUL;
-}
-
-struct pci_ops adm8668_pci_ops = {
-	.read = pci_read_config,
-	.write = pci_write_config
-};
-
-
-struct resource pciioport_resource = {
-	.name	= "adm8668_pci",
-	.start	= ADMPCI_IO_BASE,
-	.end	= ADMPCI_IO_BASE + ADMPCI_IO_SIZE,
-	.flags	= IORESOURCE_IO
-};
-
-struct resource pciiomem_resource = {
-	.name	= "adm8668_pci",
-	.start	= ADMPCI_MEM_BASE,
-	.end	= ADMPCI_MEM_BASE + ADMPCI_MEM_SIZE,
-	.flags	= IORESOURCE_MEM
-};
-
-struct pci_controller adm8668_pci_controller = {
-	.pci_ops	= &adm8668_pci_ops,
-	.io_resource	= &pciioport_resource,
-	.mem_resource	= &pciiomem_resource,
-};
-
-int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
-{
-	switch (slot) {
-	case 1:
-		return 14;
-	case 2:
-		return 13;
-	case 3:
-		return 12;
-	default:
-		return dev->irq;
-	}
-}
-
-int pcibios_plat_dev_init(struct pci_dev *dev)
-{
-	return 0;
-}
-
-static void adm8668_pci_fixup(struct pci_dev *dev)
-{
-	if (dev->devfn != 0)
-		return;
-
-	pr_info("PCI: fixing up ADM8668 controller\n");
-
-	/* setup COMMAND register */
-	pci_write_config_word(dev, PCI_COMMAND,
-		(PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER));
-
-	/* setup CACHE_LINE_SIZE register */
-	pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, 4);
-
-	/* setup BARS */
-	pci_write_config_dword(dev, PCI_BASE_ADDRESS_0, 0);
-	pci_write_config_dword(dev, PCI_BASE_ADDRESS_1, 0);
-}
-DECLARE_PCI_FIXUP_HEADER(0x1317, 0x8688, adm8668_pci_fixup);
-
-static int __init adm8668_pci_init(void)
-{
-	void __iomem *io_map_base;
-
-	ioport_resource.start   = ADMPCI_IO_BASE;
-	ioport_resource.end     = ADMPCI_IO_BASE + ADMPCI_IO_SIZE;
-
-	io_map_base = ioremap(ADMPCI_IO_BASE, ADMPCI_IO_SIZE);
-	if (!io_map_base)
-		printk("io_map_base didn't work.\n");
-
-	adm8668_pci_controller.io_map_base = (unsigned long)io_map_base;
-	register_pci_controller(&adm8668_pci_controller);
-
-	return 0;
-}
-arch_initcall(adm8668_pci_init);

target/linux/adm8668/files-3.14/drivers/mtd/maps/adm8668.c

@@ -1,334 +0,0 @@
-/*
- *  Copyright (C) 2010 Scott Nicholas <[email protected]>
- *  Copyright (C) 2006 Felix Fietkau <[email protected]>
- *  Copyright (C) 2005 Waldemar Brodkorb <[email protected]>
- *  Copyright (C) 2004 Florian Schirmer ([email protected])
- *
- *  original functions for finding root filesystem from Mike Baker
- *
- *  This program is free software; you can redistribute  it and/or modify it
- *  under  the terms of  the GNU General  Public License as published by the
- *  Free Software Foundation;  either version 2 of the  License, or (at your
- *  option) any later version.
- *
- *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
- *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
- *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
- *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
- *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
- *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
- *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- *  You should have received a copy of the  GNU General Public License along
- *  with this program; if not, write  to the Free Software Foundation, Inc.,
- *  675 Mass Ave, Cambridge, MA 02139, USA.
- *
- *
- * Copyright 2004, Broadcom Corporation
- * All Rights Reserved.
- *
- * THIS SOFTWARE IS OFFERED "AS IS", AND BROADCOM GRANTS NO WARRANTIES OF ANY
- * KIND, EXPRESS OR IMPLIED, BY STATUTE, COMMUNICATION OR OTHERWISE. BROADCOM
- * SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS
- * FOR A SPECIFIC PURPOSE OR NONINFRINGEMENT CONCERNING THIS SOFTWARE.
- *
- * Flash mapping for adm8668 boards
- *
- */
-
-#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/sched.h>
-#include <linux/wait.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/map.h>
-#include <linux/slab.h>
-#include <linux/mtd/partitions.h>
-#include <linux/crc32.h>
-#include <linux/magic.h>
-#include <asm/io.h>
-
-#define WINDOW_ADDR	0x10000000
-#define WINDOW_SIZE	0x800000
-#define BANKWIDTH	2
-
-/* first a little bit about the headers i need.. */
-
-/* just interested in part of the full struct */
-struct squashfs_super_block {
-        __le32  s_magic;
-        __le32  pad0[9];        /* it's not really padding */
-        __le64  bytes_used;
-};
-
-#define IH_MAGIC	0x56190527	/* Image Magic Number		*/
-struct uboot_header {
-	uint32_t	ih_magic;	/* Image Header Magic Number	*/
-	uint32_t	ih_hcrc;	/* Image Header CRC Checksum	*/
-	uint32_t	ih_time;	/* Image Creation Timestamp	*/
-	uint32_t	ih_size;	/* Image Data Size		*/
-	uint32_t	ih_load;	/* Data	 Load  Address		*/
-	uint32_t	ih_ep;		/* Entry Point Address		*/
-	uint32_t	ih_dcrc;	/* Image Data CRC Checksum	*/
-	uint8_t		ih_os;		/* Operating System		*/
-	uint8_t		ih_arch;	/* CPU architecture		*/
-	uint8_t		ih_type;	/* Image Type			*/
-	uint8_t		ih_comp;	/* Compression Type		*/
-	char		ih_name[32];	/* image name */
-};
-
-/************************************************/
-
-static struct mtd_info *adm8668_mtd;
-
-struct map_info adm8668_map = {
-	name: "adm8668-nor",
-	size: WINDOW_SIZE,
-	phys: WINDOW_ADDR,
-	bankwidth: BANKWIDTH,
-};
-
-/*
- * Copied from mtdblock.c
- *
- * Cache stuff...
- *
- * Since typical flash erasable sectors are much larger than what Linux's
- * buffer cache can handle, we must implement read-modify-write on flash
- * sectors for each block write requests.  To avoid over-erasing flash sectors
- * and to speed things up, we locally cache a whole flash sector while it is
- * being written to until a different sector is required.
- */
-
-static void erase_callback(struct erase_info *done)
-{
-	wait_queue_head_t *wait_q = (wait_queue_head_t *)done->priv;
-	wake_up(wait_q);
-}
-
-static int erase_write (struct mtd_info *mtd, unsigned long pos,
-			int len, const char *buf)
-{
-	struct erase_info erase;
-	DECLARE_WAITQUEUE(wait, current);
-	wait_queue_head_t wait_q;
-	size_t retlen;
-	int ret;
-
-	/*
-	 * First, let's erase the flash block.
-	 */
-
-	init_waitqueue_head(&wait_q);
-	erase.mtd = mtd;
-	erase.callback = erase_callback;
-	erase.addr = pos;
-	erase.len = len;
-	erase.priv = (u_long)&wait_q;
-
-	set_current_state(TASK_INTERRUPTIBLE);
-	add_wait_queue(&wait_q, &wait);
-
-	ret = mtd->_erase(mtd, &erase);
-	if (ret) {
-		set_current_state(TASK_RUNNING);
-		remove_wait_queue(&wait_q, &wait);
-		printk (KERN_WARNING "erase of region [0x%lx, 0x%x] "
-				     "on \"%s\" failed\n",
-			pos, len, mtd->name);
-		return ret;
-	}
-
-	schedule();  /* Wait for erase to finish. */
-	remove_wait_queue(&wait_q, &wait);
-
-	/*
-	 * Next, write data to flash.
-	 */
-
-	ret = mtd->_write (mtd, pos, len, &retlen, buf);
-	if (ret)
-		return ret;
-	if (retlen != len)
-		return -EIO;
-	return 0;
-}
-
-/* decent defaults in case... shrug */
-static struct mtd_partition adm8668_parts[] = {
-	{ name: "linux",	offset: 0x40000,	size: WINDOW_SIZE-0x40000, },
-	{ name: "rootfs",	offset: 0xe0000,	size: 0x140000, },
-	{ name: "uboot_env",	offset: 0x20000,	size: 0x20000, },
-	{ name: NULL, },
-};
-
-/* in case i wanna change stuff later, and to clarify the math section... */
-#define	PART_LINUX	0
-#define	PART_ROOTFS	1
-#define	NR_PARTS	3
-
-static int __init
-init_mtd_partitions(struct mtd_info *mtd, size_t size)
-{
-	struct uboot_header uhdr;
-	int off, blocksize;
-	size_t len, linux_len;
-	struct squashfs_super_block shdr;
-
-	blocksize = mtd->erasesize;
-	if (blocksize < 0x10000)
-		blocksize = 0x10000;
-
-	/* now find squashfs */
-	memset(&shdr, 0xe5, sizeof(shdr));
-	for (off = adm8668_parts[PART_LINUX].offset; off < size; off += blocksize) {
-		/*
-		 * Read into buffer
-		 */
-		if (mtd->_read(mtd, off, sizeof(shdr), &len, (char *)&shdr) ||
-		    len != sizeof(shdr))
-			continue;
-
-		if (shdr.s_magic == SQUASHFS_MAGIC) {
-			uint32_t fs_size = (uint32_t)shdr.bytes_used;
-
-			printk(KERN_INFO "%s: Filesystem type: squashfs, size=%dkB\n",
-				mtd->name, fs_size>>10);
-
-			/* Update rootfs based on the superblock info, and
-			 * stretch to end of MTD. rootfs_split will split it */
-			adm8668_parts[PART_ROOTFS].offset = off;
-			adm8668_parts[PART_ROOTFS].size = mtd->size -
-				adm8668_parts[PART_ROOTFS].offset;
-
-			/* kernel ends where rootfs starts
-			 * but we'll keep it full-length for upgrades */
-			linux_len = adm8668_parts[PART_LINUX+1].offset -
-				adm8668_parts[PART_LINUX].offset;
-#if 1
-			adm8668_parts[PART_LINUX].size = mtd->size -
-				adm8668_parts[PART_LINUX].offset;
-#else
-			adm8668_parts[PART_LINUX].size = linux_len;
-#endif
-			goto found;
-		}
-	}
-
-	printk(KERN_NOTICE
-	       "%s: Couldn't find root filesystem\n",
-	       mtd->name);
-	return NR_PARTS;
-
- found:
-	if (mtd->_read(mtd, adm8668_parts[PART_LINUX].offset, sizeof(uhdr), &len, (char *)&uhdr) ||
-	    len != sizeof(uhdr))
-		return NR_PARTS;
-
-	/* that's odd. how'd ya boot it then */
-	if (uhdr.ih_magic != IH_MAGIC)
-		return NR_PARTS;
-
-	if (be32_to_cpu(uhdr.ih_size) != (linux_len - sizeof(uhdr))) {
-		unsigned char *block, *data;
-		unsigned int offset;
-
-		offset = adm8668_parts[PART_LINUX].offset +
-			 sizeof(struct uboot_header);
-		data = (unsigned char *)(WINDOW_ADDR | 0xA0000000 | offset);
-
-		printk(KERN_NOTICE "Updating U-boot image:\n");
-		printk(KERN_NOTICE "  old: [size: %8d crc32: 0x%08x]\n",
-			be32_to_cpu(uhdr.ih_size), be32_to_cpu(uhdr.ih_dcrc));
-
-		/* Update the data length & crc32 */
-		uhdr.ih_size = cpu_to_be32(linux_len - sizeof(uhdr));
-		uhdr.ih_dcrc = crc32_le(~0, data, linux_len - sizeof(uhdr)) ^ (~0);
-		uhdr.ih_dcrc = cpu_to_be32(uhdr.ih_dcrc);
-
-		printk(KERN_NOTICE "  new: [size: %8d crc32: 0x%08x]\n",
-			be32_to_cpu(uhdr.ih_size), be32_to_cpu(uhdr.ih_dcrc));
-
-		/* update header's crc... */
-		uhdr.ih_hcrc = 0;
-		uhdr.ih_hcrc = crc32_le(~0, (unsigned char *)&uhdr,
-				sizeof(uhdr)) ^ (~0);
-		uhdr.ih_hcrc = cpu_to_be32(uhdr.ih_hcrc);
-
-		/* read first eraseblock from the image */
-		block = kmalloc(mtd->erasesize, GFP_KERNEL);
-		if (mtd->_read(mtd, adm8668_parts[PART_LINUX].offset, mtd->erasesize, &len, block) || len != mtd->erasesize) {
-			printk("Error copying first eraseblock\n");
-			return 0;
-		}
-
-		/* Write updated header to the flash */
-		memcpy(block, &uhdr, sizeof(uhdr));
-		if (mtd->_unlock)
-			mtd->_unlock(mtd, off, mtd->erasesize);
-		erase_write(mtd, adm8668_parts[PART_LINUX].offset, mtd->erasesize, block);
-		if (mtd->_sync)
-			mtd->_sync(mtd);
-		kfree(block);
-		printk(KERN_NOTICE "Done\n");
-	}
-
-	return NR_PARTS;
-}
-
-int __init init_adm8668_map(void)
-{
-	int nr_parts, ret;
-
-	adm8668_map.virt = ioremap(WINDOW_ADDR, WINDOW_SIZE);
-
-	if (!adm8668_map.virt) {
-		printk(KERN_ERR "Failed to ioremap\n");
-		return -EIO;
-	}
-
-	simple_map_init(&adm8668_map);
-	if (!(adm8668_mtd = do_map_probe("cfi_probe", &adm8668_map))) {
-		printk(KERN_ERR "cfi_probe failed\n");
-		iounmap((void *)adm8668_map.virt);
-		return -ENXIO;
-	}
-
-	adm8668_mtd->owner = THIS_MODULE;
-
-	nr_parts = init_mtd_partitions(adm8668_mtd, adm8668_mtd->size);
-	ret = mtd_device_register(adm8668_mtd, adm8668_parts, nr_parts);
-	if (ret) {
-		printk(KERN_ERR "Flash: mtd_device_register failed\n");
-		goto fail;
-	}
-
-	return 0;
-
- fail:
-	if (adm8668_mtd)
-		map_destroy(adm8668_mtd);
-	if (adm8668_map.virt)
-		iounmap((void *) adm8668_map.virt);
-	adm8668_map.virt = 0;
-	return ret;
-}
-
-void __exit cleanup_adm8668_map(void)
-{
-	mtd_device_unregister(adm8668_mtd);
-	map_destroy(adm8668_mtd);
-	iounmap((void *) adm8668_map.virt);
-	adm8668_map.virt = 0;
-}
-
-module_init(init_adm8668_map);
-module_exit(cleanup_adm8668_map);
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Scott Nicholas <[email protected]>");
-MODULE_DESCRIPTION("MTD map driver for ADM8668 NOR Flash");

target/linux/adm8668/patches-3.14/001-adm8668_arch.patch

@@ -1,48 +0,0 @@
---- a/arch/mips/Kbuild.platforms
-+++ b/arch/mips/Kbuild.platforms
-@@ -29,6 +29,7 @@ platforms += sibyte
- platforms += sni
- platforms += txx9
- platforms += vr41xx
-+platforms += adm8668
- 
- # include the platform specific files
- include $(patsubst %, $(srctree)/arch/mips/%/Platform, $(platforms))
---- a/arch/mips/Kconfig
-+++ b/arch/mips/Kconfig
-@@ -127,6 +127,27 @@ config BCM47XX
- 	help
- 	 Support for BCM47XX based boards
- 
-+config ADM8668
-+	bool "WildPass ADM8668"
-+	select SYS_HAS_CPU_MIPS32_R1
-+	select BOOT_RAW
-+	select NO_EXCEPT_FILL
-+	select IRQ_CPU
-+	select CEVT_R4K
-+	select CSRC_R4K
-+	select HW_HAS_PCI
-+	select PCI
-+	select SYS_SUPPORTS_LITTLE_ENDIAN
-+	select SYS_SUPPORTS_32BIT_KERNEL
-+	select DMA_NONCOHERENT
-+	select SWAP_IO_SPACE
-+	select SYS_HAS_EARLY_PRINTK
-+	select ARCH_REQUIRE_GPIOLIB
-+	select HAVE_CLK
-+	help
-+		ADM8668 board support by neutronscott
-+		Scott Nicholas <[email protected]>
-+
- config BCM63XX
- 	bool "Broadcom BCM63XX based boards"
- 	select BOOT_RAW
-@@ -795,6 +816,7 @@ config NLM_XLP_BOARD
- 
- endchoice
- 
-+source "arch/mips/adm8668/Kconfig"
- source "arch/mips/alchemy/Kconfig"
- source "arch/mips/ath79/Kconfig"
- source "arch/mips/bcm47xx/Kconfig"

target/linux/adm8668/patches-3.14/002-adm8668_pci.patch

@@ -1,22 +0,0 @@
---- a/arch/mips/pci/Makefile
-+++ b/arch/mips/pci/Makefile
-@@ -57,6 +57,7 @@ obj-$(CONFIG_MIKROTIK_RB532)	+= pci-rc32
- obj-$(CONFIG_CAVIUM_OCTEON_SOC) += pci-octeon.o pcie-octeon.o
- obj-$(CONFIG_CPU_XLR)		+= pci-xlr.o
- obj-$(CONFIG_CPU_XLP)		+= pci-xlp.o
-+obj-$(CONFIG_ADM8668)		+= pci-adm8668.o
- 
- ifdef CONFIG_PCI_MSI
- obj-$(CONFIG_CAVIUM_OCTEON_SOC) += msi-octeon.o
---- a/include/linux/pci_ids.h
-+++ b/include/linux/pci_ids.h
-@@ -1817,6 +1817,9 @@
- 
- #define PCI_VENDOR_ID_CB		0x1307	/* Measurement Computing */
- 
-+#define PCI_VENDOR_ADMTEK		0x1317
-+#define PCI_DEVICE_ID_ADM8668		0x8688
-+
- #define PCI_VENDOR_ID_SIIG		0x131f
- #define PCI_SUBVENDOR_ID_SIIG		0x131f
- #define PCI_DEVICE_ID_SIIG_1S_10x_550	0x1000

target/linux/adm8668/patches-3.14/003-adm8668_nor_map.patch

@@ -1,22 +0,0 @@
---- a/drivers/mtd/maps/Kconfig
-+++ b/drivers/mtd/maps/Kconfig
-@@ -97,6 +97,12 @@ config MSP_FLASH_MAP_LIMIT
- 	default "0x02000000"
- 	depends on MSP_FLASH_MAP_LIMIT_32M
- 
-+config MTD_ADM8668_NOR
-+	tristate "ADM8668 NOR mapping"
-+	depends on ADM8668 && MTD_CFI
-+	help
-+	  mapping driver for ADM8668 NOR
-+
- config MTD_SUN_UFLASH
- 	tristate "Sun Microsystems userflash support"
- 	depends on SPARC && MTD_CFI && PCI
---- a/drivers/mtd/maps/Makefile
-+++ b/drivers/mtd/maps/Makefile
-@@ -43,3 +43,4 @@ obj-$(CONFIG_MTD_VMU)		+= vmu-flash.o
- obj-$(CONFIG_MTD_GPIO_ADDR)	+= gpio-addr-flash.o
- obj-$(CONFIG_MTD_LATCH_ADDR)	+= latch-addr-flash.o
- obj-$(CONFIG_MTD_LANTIQ)	+= lantiq-flash.o
-+obj-$(CONFIG_MTD_ADM8668_NOR)	+= adm8668.o

target/linux/adm8668/patches-3.14/004-tulip_pci_split.patch

@@ -1,453 +0,0 @@
---- a/drivers/net/ethernet/dec/tulip/tulip_core.c
-+++ b/drivers/net/ethernet/dec/tulip/tulip_core.c
-@@ -206,7 +206,7 @@ struct tulip_chip_table tulip_tbl[] = {
- 
- };
- 
--
-+#ifdef CONFIG_TULIP_PCI
- static DEFINE_PCI_DEVICE_TABLE(tulip_pci_tbl) = {
- 	{ 0x1011, 0x0009, PCI_ANY_ID, PCI_ANY_ID, 0, 0, DC21140 },
- 	{ 0x1011, 0x0019, PCI_ANY_ID, PCI_ANY_ID, 0, 0, DC21143 },
-@@ -250,7 +250,7 @@ static DEFINE_PCI_DEVICE_TABLE(tulip_pci
- 	{ } /* terminate list */
- };
- MODULE_DEVICE_TABLE(pci, tulip_pci_tbl);
--
-+#endif
- 
- /* A full-duplex map for media types. */
- const char tulip_media_cap[32] =
-@@ -268,11 +268,14 @@ static void tulip_down(struct net_device
- static struct net_device_stats *tulip_get_stats(struct net_device *dev);
- static int private_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
- static void set_rx_mode(struct net_device *dev);
-+#ifdef CONFIG_TULIP_PCI
- static void tulip_set_wolopts(struct pci_dev *pdev, u32 wolopts);
-+#endif
- #ifdef CONFIG_NET_POLL_CONTROLLER
- static void poll_tulip(struct net_device *dev);
- #endif
- 
-+#ifdef CONFIG_TULIP_PCI
- static void tulip_set_power_state (struct tulip_private *tp,
- 				   int sleep, int snooze)
- {
-@@ -289,7 +292,7 @@ static void tulip_set_power_state (struc
- 	}
- 
- }
--
-+#endif
- 
- static void tulip_up(struct net_device *dev)
- {
-@@ -303,6 +306,7 @@ static void tulip_up(struct net_device *
- 	napi_enable(&tp->napi);
- #endif
- 
-+#ifdef CONFIG_TULIP_PCI
- 	/* Wake the chip from sleep/snooze mode. */
- 	tulip_set_power_state (tp, 0, 0);
- 
-@@ -310,6 +314,7 @@ static void tulip_up(struct net_device *
- 	pci_enable_wake(tp->pdev, PCI_D3hot, 0);
- 	pci_enable_wake(tp->pdev, PCI_D3cold, 0);
- 	tulip_set_wolopts(tp->pdev, 0);
-+#endif
- 
- 	/* On some chip revs we must set the MII/SYM port before the reset!? */
- 	if (tp->mii_cnt  ||  (tp->mtable  &&  tp->mtable->has_mii))
-@@ -317,18 +322,22 @@ static void tulip_up(struct net_device *
- 
- 	/* Reset the chip, holding bit 0 set at least 50 PCI cycles. */
- 	iowrite32(0x00000001, ioaddr + CSR0);
-+#ifdef CONFIG_TULIP_PCI
- 	pci_read_config_dword(tp->pdev, PCI_COMMAND, &reg);  /* flush write */
-+#endif
- 	udelay(100);
- 
- 	/* Deassert reset.
- 	   Wait the specified 50 PCI cycles after a reset by initializing
- 	   Tx and Rx queues and the address filter list. */
- 	iowrite32(tp->csr0, ioaddr + CSR0);
-+#ifdef CONFIG_TULIP_PCI
- 	pci_read_config_dword(tp->pdev, PCI_COMMAND, &reg);  /* flush write */
-+#endif
- 	udelay(100);
- 
- 	if (tulip_debug > 1)
--		netdev_dbg(dev, "tulip_up(), irq==%d\n", tp->pdev->irq);
-+		netdev_dbg(dev, "tulip_up(), irq==%d\n", tp->irq);
- 
- 	iowrite32(tp->rx_ring_dma, ioaddr + CSR3);
- 	iowrite32(tp->tx_ring_dma, ioaddr + CSR4);
-@@ -362,9 +371,11 @@ static void tulip_up(struct net_device *
- 		*setup_frm++ = eaddrs[1]; *setup_frm++ = eaddrs[1];
- 		*setup_frm++ = eaddrs[2]; *setup_frm++ = eaddrs[2];
- 
-+#ifdef CONFIG_TULIP_PCI
- 		mapping = pci_map_single(tp->pdev, tp->setup_frame,
- 					 sizeof(tp->setup_frame),
- 					 PCI_DMA_TODEVICE);
-+#endif
- 		tp->tx_buffers[tp->cur_tx].skb = NULL;
- 		tp->tx_buffers[tp->cur_tx].mapping = mapping;
- 
-@@ -520,7 +531,7 @@ tulip_open(struct net_device *dev)
- 
- 	tulip_init_ring (dev);
- 
--	retval = request_irq(tp->pdev->irq, tulip_interrupt, IRQF_SHARED,
-+	retval = request_irq(tp->irq, tulip_interrupt, IRQF_SHARED,
- 			     dev->name, dev);
- 	if (retval)
- 		goto free_ring;
-@@ -644,8 +655,10 @@ static void tulip_init_ring(struct net_d
- 		tp->rx_buffers[i].skb = skb;
- 		if (skb == NULL)
- 			break;
-+#ifdef CONFIG_TULIP_PCI
- 		mapping = pci_map_single(tp->pdev, skb->data,
- 					 PKT_BUF_SZ, PCI_DMA_FROMDEVICE);
-+#endif
- 		tp->rx_buffers[i].mapping = mapping;
- 		tp->rx_ring[i].status = cpu_to_le32(DescOwned);	/* Owned by Tulip chip */
- 		tp->rx_ring[i].buffer1 = cpu_to_le32(mapping);
-@@ -678,8 +691,10 @@ tulip_start_xmit(struct sk_buff *skb, st
- 	entry = tp->cur_tx % TX_RING_SIZE;
- 
- 	tp->tx_buffers[entry].skb = skb;
-+#ifdef CONFIG_TULIP_PCI
- 	mapping = pci_map_single(tp->pdev, skb->data,
- 				 skb->len, PCI_DMA_TODEVICE);
-+#endif
- 	tp->tx_buffers[entry].mapping = mapping;
- 	tp->tx_ring[entry].buffer1 = cpu_to_le32(mapping);
- 
-@@ -730,16 +745,19 @@ static void tulip_clean_tx_ring(struct t
- 		if (tp->tx_buffers[entry].skb == NULL) {
- 			/* test because dummy frames not mapped */
- 			if (tp->tx_buffers[entry].mapping)
-+#ifdef CONFIG_TULIP_PCI
- 				pci_unmap_single(tp->pdev,
- 					tp->tx_buffers[entry].mapping,
- 					sizeof(tp->setup_frame),
- 					PCI_DMA_TODEVICE);
-+#endif
- 			continue;
- 		}
--
-+#ifdef CONFIG_TULIP_PCI
- 		pci_unmap_single(tp->pdev, tp->tx_buffers[entry].mapping,
- 				tp->tx_buffers[entry].skb->len,
- 				PCI_DMA_TODEVICE);
-+#endif
- 
- 		/* Free the original skb. */
- 		dev_kfree_skb_irq(tp->tx_buffers[entry].skb);
-@@ -790,7 +808,9 @@ static void tulip_down (struct net_devic
- 	dev->if_port = tp->saved_if_port;
- 
- 	/* Leave the driver in snooze, not sleep, mode. */
-+#ifdef CONFIG_TULIP_PCI
- 	tulip_set_power_state (tp, 0, 1);
-+#endif
- }
- 
- static void tulip_free_ring (struct net_device *dev)
-@@ -811,8 +831,10 @@ static void tulip_free_ring (struct net_
- 		/* An invalid address. */
- 		tp->rx_ring[i].buffer1 = cpu_to_le32(0xBADF00D0);
- 		if (skb) {
-+#ifdef CONFIG_TULIP_PCI
- 			pci_unmap_single(tp->pdev, mapping, PKT_BUF_SZ,
- 					 PCI_DMA_FROMDEVICE);
-+#endif
- 			dev_kfree_skb (skb);
- 		}
- 	}
-@@ -821,8 +843,10 @@ static void tulip_free_ring (struct net_
- 		struct sk_buff *skb = tp->tx_buffers[i].skb;
- 
- 		if (skb != NULL) {
-+#ifdef CONFIG_TULIP_PCI
- 			pci_unmap_single(tp->pdev, tp->tx_buffers[i].mapping,
- 					 skb->len, PCI_DMA_TODEVICE);
-+#endif
- 			dev_kfree_skb (skb);
- 		}
- 		tp->tx_buffers[i].skb = NULL;
-@@ -843,7 +867,7 @@ static int tulip_close (struct net_devic
- 		netdev_dbg(dev, "Shutting down ethercard, status was %02x\n",
- 			   ioread32 (ioaddr + CSR5));
- 
--	free_irq (tp->pdev->irq, dev);
-+	free_irq (tp->irq, dev);
- 
- 	tulip_free_ring (dev);
- 
-@@ -874,7 +898,9 @@ static void tulip_get_drvinfo(struct net
- 	struct tulip_private *np = netdev_priv(dev);
- 	strlcpy(info->driver, DRV_NAME, sizeof(info->driver));
- 	strlcpy(info->version, DRV_VERSION, sizeof(info->version));
-+#ifdef CONFIG_TULIP_PCI
- 	strlcpy(info->bus_info, pci_name(np->pdev), sizeof(info->bus_info));
-+#endif
- }
- 
- 
-@@ -887,7 +913,9 @@ static int tulip_ethtool_set_wol(struct 
- 		   return -EOPNOTSUPP;
- 
- 	tp->wolinfo.wolopts = wolinfo->wolopts;
--	device_set_wakeup_enable(&tp->pdev->dev, tp->wolinfo.wolopts);
-+#ifdef CONFIG_TULIP_PCI
-+	device_set_wakeup_enable(tp->kdev, tp->wolinfo.wolopts);
-+#endif
- 	return 0;
- }
- 
-@@ -1165,9 +1193,11 @@ static void set_rx_mode(struct net_devic
- 
- 			tp->tx_buffers[entry].skb = NULL;
- 			tp->tx_buffers[entry].mapping =
-+#ifdef CONFIG_TULIP_PCI
- 				pci_map_single(tp->pdev, tp->setup_frame,
- 					       sizeof(tp->setup_frame),
- 					       PCI_DMA_TODEVICE);
-+#endif
- 			/* Put the setup frame on the Tx list. */
- 			if (entry == TX_RING_SIZE-1)
- 				tx_flags |= DESC_RING_WRAP;		/* Wrap ring. */
-@@ -1264,19 +1294,22 @@ out:
- 		netdev_dbg(dev, "MWI config cacheline=%d, csr0=%08x\n",
- 			   cache, csr0);
- }
--#endif
- 
- /*
-  *	Chips that have the MRM/reserved bit quirk and the burst quirk. That
-  *	is the DM910X and the on chip ULi devices
-  */
-+#endif
- 
-+#ifdef CONFIG_TULIP_PCI
- static int tulip_uli_dm_quirk(struct pci_dev *pdev)
- {
- 	if (pdev->vendor == 0x1282 && pdev->device == 0x9102)
- 		return 1;
- 	return 0;
- }
-+#endif
-+
- 
- static const struct net_device_ops tulip_netdev_ops = {
- 	.ndo_open		= tulip_open,
-@@ -1294,6 +1327,7 @@ static const struct net_device_ops tulip
- #endif
- };
- 
-+#ifdef CONFIG_TULIP_PCI
- DEFINE_PCI_DEVICE_TABLE(early_486_chipsets) = {
- 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82424) },
- 	{ PCI_DEVICE(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_496) },
-@@ -1471,6 +1505,8 @@ static int tulip_init_one(struct pci_dev
- 		}
- 	}
- 	tp->pdev = pdev;
-+	tp->kdev = &pdev->dev;
-+	tp->irq = irq;
- 	tp->base_addr = ioaddr;
- 	tp->revision = pdev->revision;
- 	tp->csr0 = csr0;
-@@ -1801,6 +1837,7 @@ err_out_free_netdev:
- }
- 
- 
-+#ifdef CONFIG_TULIP_PCI
- /* set the registers according to the given wolopts */
- static void tulip_set_wolopts (struct pci_dev *pdev, u32 wolopts)
- {
-@@ -1829,6 +1866,7 @@ static void tulip_set_wolopts (struct pc
- 		iowrite32(tmp, ioaddr + CSR13);
- 	}
- }
-+#endif
- 
- #ifdef CONFIG_PM
- 
-@@ -1943,6 +1981,7 @@ static void tulip_remove_one(struct pci_
- 
- 	/* pci_power_off (pdev, -1); */
- }
-+#endif /* CONFIG_TULIP_PCI */
- 
- #ifdef CONFIG_NET_POLL_CONTROLLER
- /*
-@@ -1964,7 +2003,8 @@ static void poll_tulip (struct net_devic
- }
- #endif
- 
--static struct pci_driver tulip_driver = {
-+#ifdef CONFIG_TULIP_PCI
-+static struct pci_driver tulip_pci_driver = {
- 	.name		= DRV_NAME,
- 	.id_table	= tulip_pci_tbl,
- 	.probe		= tulip_init_one,
-@@ -1974,10 +2014,12 @@ static struct pci_driver tulip_driver = 
- 	.resume		= tulip_resume,
- #endif /* CONFIG_PM */
- };
-+#endif
- 
- 
- static int __init tulip_init (void)
- {
-+	int ret = 0;
- #ifdef MODULE
- 	pr_info("%s", version);
- #endif
-@@ -1987,13 +2029,18 @@ static int __init tulip_init (void)
- 	tulip_max_interrupt_work = max_interrupt_work;
- 
- 	/* probe for and init boards */
--	return pci_register_driver(&tulip_driver);
-+#ifdef CONFIG_TULIP_PCI
-+	ret = pci_register_driver(&tulip_pci_driver);
-+#endif
-+	return ret;
- }
- 
- 
- static void __exit tulip_cleanup (void)
- {
--	pci_unregister_driver (&tulip_driver);
-+#ifdef CONFIG_TULIP_PCI
-+	pci_unregister_driver (&tulip_pci_driver);
-+#endif
- }
- 
- 
---- a/drivers/net/ethernet/dec/tulip/interrupt.c
-+++ b/drivers/net/ethernet/dec/tulip/interrupt.c
-@@ -73,10 +73,11 @@ int tulip_refill_rx(struct net_device *d
- 				netdev_alloc_skb(dev, PKT_BUF_SZ);
- 			if (skb == NULL)
- 				break;
--
-+#ifdef CONFIG_TULIP_PCI
- 			mapping = pci_map_single(tp->pdev, skb->data, PKT_BUF_SZ,
- 						 PCI_DMA_FROMDEVICE);
--			if (dma_mapping_error(&tp->pdev->dev, mapping)) {
-+#endif
-+			if (dma_mapping_error(tp->kdev, mapping)) {
- 				dev_kfree_skb(skb);
- 				tp->rx_buffers[entry].skb = NULL;
- 				break;
-@@ -210,9 +211,11 @@ int tulip_poll(struct napi_struct *napi,
-                                if (pkt_len < tulip_rx_copybreak &&
-                                    (skb = netdev_alloc_skb(dev, pkt_len + 2)) != NULL) {
-                                        skb_reserve(skb, 2);    /* 16 byte align the IP header */
-+#ifdef CONFIG_TULIP_PCI
-                                        pci_dma_sync_single_for_cpu(tp->pdev,
- 								   tp->rx_buffers[entry].mapping,
- 								   pkt_len, PCI_DMA_FROMDEVICE);
-+#endif
- #if ! defined(__alpha__)
-                                        skb_copy_to_linear_data(skb, tp->rx_buffers[entry].skb->data,
-                                                         pkt_len);
-@@ -222,9 +225,11 @@ int tulip_poll(struct napi_struct *napi,
-                                               tp->rx_buffers[entry].skb->data,
-                                               pkt_len);
- #endif
-+#ifdef CONFIG_TULIP_PCI
-                                        pci_dma_sync_single_for_device(tp->pdev,
- 								      tp->rx_buffers[entry].mapping,
- 								      pkt_len, PCI_DMA_FROMDEVICE);
-+#endif
-                                } else {        /* Pass up the skb already on the Rx ring. */
-                                        char *temp = skb_put(skb = tp->rx_buffers[entry].skb,
-                                                             pkt_len);
-@@ -239,9 +244,10 @@ int tulip_poll(struct napi_struct *napi,
- 						       skb->head, temp);
-                                        }
- #endif
--
-+#ifdef CONFIG_TULIP_PCI
-                                        pci_unmap_single(tp->pdev, tp->rx_buffers[entry].mapping,
-                                                         PKT_BUF_SZ, PCI_DMA_FROMDEVICE);
-+#endif
- 
-                                        tp->rx_buffers[entry].skb = NULL;
-                                        tp->rx_buffers[entry].mapping = 0;
-@@ -597,10 +603,12 @@ irqreturn_t tulip_interrupt(int irq, voi
- 				if (tp->tx_buffers[entry].skb == NULL) {
- 					/* test because dummy frames not mapped */
- 					if (tp->tx_buffers[entry].mapping)
-+#ifdef CONFIG_TULIP_PCI
- 						pci_unmap_single(tp->pdev,
- 							 tp->tx_buffers[entry].mapping,
- 							 sizeof(tp->setup_frame),
- 							 PCI_DMA_TODEVICE);
-+#endif
- 					continue;
- 				}
- 
-@@ -628,10 +636,11 @@ irqreturn_t tulip_interrupt(int irq, voi
- 					dev->stats.collisions += (status >> 3) & 15;
- 					dev->stats.tx_packets++;
- 				}
--
-+#ifdef CONFIG_TULIP_PCI
- 				pci_unmap_single(tp->pdev, tp->tx_buffers[entry].mapping,
- 						 tp->tx_buffers[entry].skb->len,
- 						 PCI_DMA_TODEVICE);
-+#endif
- 
- 				/* Free the original skb. */
- 				dev_kfree_skb_irq(tp->tx_buffers[entry].skb);
---- a/drivers/net/ethernet/dec/tulip/Kconfig
-+++ b/drivers/net/ethernet/dec/tulip/Kconfig
-@@ -40,8 +40,12 @@ config DE2104X_DSL
- 	  Default is 0, and range is 0 to 31.
- 
- config TULIP
-+	tristate
-+
-+config TULIP_PCI
- 	tristate "DECchip Tulip (dc2114x) PCI support"
- 	depends on PCI
-+	select TULIP
- 	select CRC32
- 	---help---
- 	  This driver is developed for the SMC EtherPower series Ethernet
-@@ -58,7 +62,7 @@ config TULIP
- 
- config TULIP_MWI
- 	bool "New bus configuration"
--	depends on TULIP
-+	depends on TULIP_PCI
- 	---help---
- 	  This configures your Tulip card specifically for the card and
- 	  system cache line size type you are using.
-@@ -69,7 +73,7 @@ config TULIP_MWI
- 
- config TULIP_MMIO
- 	bool "Use PCI shared mem for NIC registers"
--	depends on TULIP
-+	depends on TULIP_PCI
- 	---help---
- 	  Use PCI shared memory for the NIC registers, rather than going through
- 	  the Tulip's PIO (programmed I/O ports).  Faster, but could produce
---- a/drivers/net/ethernet/dec/tulip/tulip.h
-+++ b/drivers/net/ethernet/dec/tulip/tulip.h
-@@ -447,6 +447,8 @@ struct tulip_private {
- 	int cur_index;		/* Current media index. */
- 	int saved_if_port;
- 	struct pci_dev *pdev;
-+	struct device *kdev;
-+	int irq;
- 	int ttimer;
- 	int susp_rx;
- 	unsigned long nir;

target/linux/adm8668/patches-3.14/005-tulip_platform.patch

@@ -1,453 +0,0 @@
---- a/drivers/net/ethernet/dec/tulip/Kconfig
-+++ b/drivers/net/ethernet/dec/tulip/Kconfig
-@@ -60,6 +60,14 @@ config TULIP_PCI
- 	  To compile this driver as a module, choose M here. The module will
- 	  be called tulip.
- 
-+config TULIP_PLATFORM
-+	tristate "DECchip Tulip (dc2114x) Platform support"
-+	depends on HAS_IOMEM
-+	select TULIP
-+	select CRC32
-+	---help---
-+	   This driver is for the platform variant.
-+
- config TULIP_MWI
- 	bool "New bus configuration"
- 	depends on TULIP_PCI
---- a/drivers/net/ethernet/dec/tulip/tulip_core.c
-+++ b/drivers/net/ethernet/dec/tulip/tulip_core.c
-@@ -27,6 +27,8 @@
- #include <linux/init.h>
- #include <linux/interrupt.h>
- #include <linux/etherdevice.h>
-+#include <linux/platform_device.h>
-+#include <linux/platform_data/tulip.h>
- #include <linux/delay.h>
- #include <linux/mii.h>
- #include <linux/crc32.h>
-@@ -204,6 +206,9 @@ struct tulip_chip_table tulip_tbl[] = {
-   { "Conexant LANfinity", 256, 0x0001ebef,
- 	HAS_MII | HAS_ACPI, tulip_timer, tulip_media_task },
- 
-+  { "Infineon ADM8668", 256, 0x0001a451,
-+	MC_HASH_ONLY | COMET_MAC_ADDR, tulip_timer, tulip_media_task, },
-+
- };
- 
- #ifdef CONFIG_TULIP_PCI
-@@ -395,6 +400,7 @@ static void tulip_up(struct net_device *
- 	i = 0;
- 	if (tp->mtable == NULL)
- 		goto media_picked;
-+
- 	if (dev->if_port) {
- 		int looking_for = tulip_media_cap[dev->if_port] & MediaIsMII ? 11 :
- 			(dev->if_port == 12 ? 0 : dev->if_port);
-@@ -488,6 +494,10 @@ media_picked:
- 		iowrite32(ioread32(ioaddr + 0x88) | 1, ioaddr + 0x88);
- 		dev->if_port = tp->mii_cnt ? 11 : 0;
- 		tp->csr6 = 0x00040000;
-+	} else if (tp->chip_id == ADM8668) {
-+		/* Enable automatic Tx underrun recovery. */
-+		iowrite32(ioread32(ioaddr + 0x88) | 1, ioaddr + 0x88);
-+		tp->csr6 = 0x00040000;
- 	} else if (tp->chip_id == AX88140) {
- 		tp->csr6 = tp->mii_cnt ? 0x00040100 : 0x00000100;
- 	} else
-@@ -659,6 +669,10 @@ static void tulip_init_ring(struct net_d
- 		mapping = pci_map_single(tp->pdev, skb->data,
- 					 PKT_BUF_SZ, PCI_DMA_FROMDEVICE);
- #endif
-+#ifdef CONFIG_TULIP_PLATFORM
-+		mapping = dma_map_single(&tp->pldev->dev, skb->data,
-+					PKT_BUF_SZ, DMA_FROM_DEVICE);
-+#endif
- 		tp->rx_buffers[i].mapping = mapping;
- 		tp->rx_ring[i].status = cpu_to_le32(DescOwned);	/* Owned by Tulip chip */
- 		tp->rx_ring[i].buffer1 = cpu_to_le32(mapping);
-@@ -695,6 +709,11 @@ tulip_start_xmit(struct sk_buff *skb, st
- 	mapping = pci_map_single(tp->pdev, skb->data,
- 				 skb->len, PCI_DMA_TODEVICE);
- #endif
-+#ifdef CONFIG_TULIP_PLATFORM
-+	mapping = dma_map_single(&tp->pldev->dev, skb->data,
-+				 skb->len,
-+				 DMA_TO_DEVICE);
-+#endif
- 	tp->tx_buffers[entry].mapping = mapping;
- 	tp->tx_ring[entry].buffer1 = cpu_to_le32(mapping);
- 
-@@ -758,6 +777,11 @@ static void tulip_clean_tx_ring(struct t
- 				tp->tx_buffers[entry].skb->len,
- 				PCI_DMA_TODEVICE);
- #endif
-+#ifdef CONFIG_TULIP_PLATFORM
-+		dma_unmap_single(&tp->pldev->dev, tp->tx_buffers[entry].mapping,
-+				tp->tx_buffers[entry].skb->len,
-+				DMA_TO_DEVICE);
-+#endif
- 
- 		/* Free the original skb. */
- 		dev_kfree_skb_irq(tp->tx_buffers[entry].skb);
-@@ -835,6 +859,10 @@ static void tulip_free_ring (struct net_
- 			pci_unmap_single(tp->pdev, mapping, PKT_BUF_SZ,
- 					 PCI_DMA_FROMDEVICE);
- #endif
-+#ifdef CONFIG_TULIP_PLATFORM
-+			dma_unmap_single(&tp->pldev->dev, mapping, PKT_BUF_SZ,
-+					DMA_FROM_DEVICE);
-+#endif
- 			dev_kfree_skb (skb);
- 		}
- 	}
-@@ -847,6 +875,10 @@ static void tulip_free_ring (struct net_
- 			pci_unmap_single(tp->pdev, tp->tx_buffers[i].mapping,
- 					 skb->len, PCI_DMA_TODEVICE);
- #endif
-+#ifdef CONFIG_TULIP_PLATFORM
-+			dma_unmap_single(&tp->pldev->dev, tp->tx_buffers[i].mapping,
-+					 skb->len, DMA_TO_DEVICE);
-+#endif
- 			dev_kfree_skb (skb);
- 		}
- 		tp->tx_buffers[i].skb = NULL;
-@@ -901,6 +933,9 @@ static void tulip_get_drvinfo(struct net
- #ifdef CONFIG_TULIP_PCI
- 	strlcpy(info->bus_info, pci_name(np->pdev), sizeof(info->bus_info));
- #endif
-+#ifdef CONFIG_TULIP_PLATFORM
-+	strlcpy(info->bus_info, "platform", sizeof(info->bus_info));
-+#endif
- }
- 
- 
-@@ -916,6 +951,9 @@ static int tulip_ethtool_set_wol(struct 
- #ifdef CONFIG_TULIP_PCI
- 	device_set_wakeup_enable(tp->kdev, tp->wolinfo.wolopts);
- #endif
-+#ifdef CONFIG_TULIP_PLATFORM
-+	device_set_wakeup_enable(&tp->pldev->dev, tp->wolinfo.wolopts);
-+#endif
- 	return 0;
- }
- 
-@@ -1191,9 +1229,9 @@ static void set_rx_mode(struct net_devic
- 
- 			}
- 
-+#ifdef CONFIG_TULIP_PCI
- 			tp->tx_buffers[entry].skb = NULL;
- 			tp->tx_buffers[entry].mapping =
--#ifdef CONFIG_TULIP_PCI
- 				pci_map_single(tp->pdev, tp->setup_frame,
- 					       sizeof(tp->setup_frame),
- 					       PCI_DMA_TODEVICE);
-@@ -1217,6 +1255,9 @@ static void set_rx_mode(struct net_devic
- 		spin_unlock_irqrestore(&tp->lock, flags);
- 	}
- 
-+	if (tp->chip_id == ADM8668)
-+		csr6 |= (1 << 9);	/* force 100Mbps full duplex */
-+
- 	iowrite32(csr6, ioaddr + CSR6);
- }
- 
-@@ -1983,6 +2024,126 @@ static void tulip_remove_one(struct pci_
- }
- #endif /* CONFIG_TULIP_PCI */
- 
-+#ifdef CONFIG_TULIP_PLATFORM
-+static int tulip_probe(struct platform_device *pdev)
-+{
-+	struct tulip_private *tp;
-+	struct tulip_platform_data *pdata;
-+	struct net_device *dev;
-+	struct resource *res;
-+	void __iomem *ioaddr;
-+	int irq;
-+
-+	if (pdev->id < 0 || pdev->id >= MAX_UNITS)
-+		return -EINVAL;
-+
-+	if (!(res = platform_get_resource(pdev, IORESOURCE_IRQ, 0)))
-+		return -ENODEV;
-+	irq = res->start;
-+	if (!(res = platform_get_resource(pdev, IORESOURCE_MEM, 0)))
-+		return -ENODEV;
-+	if (!(ioaddr = ioremap(res->start, res->end - res->start)))
-+		return -ENODEV;
-+
-+	pdata = pdev->dev.platform_data;
-+	if (!pdata)
-+		return -ENODEV;
-+
-+	if (!(dev = alloc_etherdev(sizeof (*tp))))
-+		return -ENOMEM;
-+
-+	/* setup net dev */
-+	dev->base_addr = (unsigned long)res->start;
-+	dev->irq = irq;
-+	SET_NETDEV_DEV(dev, &pdev->dev);
-+
-+	/* tulip private struct */
-+	tp = netdev_priv(dev);
-+	tp->dev = dev;
-+	tp->base_addr = ioaddr;
-+	tp->csr0 = 0;
-+	tp->pldev = pdev;
-+	tp->kdev = &pdev->dev;
-+	tp->irq = irq;
-+	tp->rx_ring = dma_alloc_coherent(&pdev->dev,
-+				sizeof(struct tulip_rx_desc) * RX_RING_SIZE +
-+				sizeof(struct tulip_tx_desc) * TX_RING_SIZE,
-+				&tp->rx_ring_dma, GFP_KERNEL);
-+	if (!tp->rx_ring)
-+		return -ENODEV;
-+	tp->tx_ring = (struct tulip_tx_desc *)(tp->rx_ring + RX_RING_SIZE);
-+	tp->tx_ring_dma = tp->rx_ring_dma + sizeof(struct tulip_rx_desc) * RX_RING_SIZE;
-+
-+	tp->chip_id = pdata->chip_id;
-+	tp->flags = tulip_tbl[tp->chip_id].flags;
-+
-+	spin_lock_init(&tp->lock);
-+	spin_lock_init(&tp->mii_lock);
-+
-+	init_timer(&tp->timer);
-+	tp->timer.data = (unsigned long)dev;
-+	tp->timer.function = tulip_tbl[tp->chip_id].media_timer;
-+
-+	INIT_WORK(&tp->media_work, tulip_tbl[tp->chip_id].media_task);
-+
-+	/* Stop the chip's Tx and Rx processes. */
-+	tulip_stop_rxtx(tp);
-+
-+	/* Clear the missed-packet counter. */
-+	ioread32(ioaddr + CSR8);
-+
-+	if (!is_valid_ether_addr(pdata->mac)) {
-+		dev_info(&pdev->dev, "generating random ethernet MAC\n");
-+		random_ether_addr(dev->dev_addr);
-+	} else
-+		memcpy(dev->dev_addr, pdata->mac, ETH_ALEN);
-+
-+	/* The Tulip-specific entries in the device structure. */
-+	dev->netdev_ops = &tulip_netdev_ops;
-+	dev->watchdog_timeo = TX_TIMEOUT;
-+	netif_napi_add(dev, &tp->napi, tulip_poll, 16);
-+	SET_ETHTOOL_OPS(dev, &ops);
-+
-+	if (register_netdev(dev))
-+		goto err_out_free_ring;
-+
-+	dev_info(&dev->dev,
-+		 "tulip_platform (%s) at MMIO %#lx %pM, IRQ %d\n",
-+		 tulip_tbl[tp->chip_id].chip_name,
-+		 (unsigned long)dev->base_addr, dev->dev_addr, irq);
-+
-+	platform_set_drvdata(pdev, dev);
-+	return 0;
-+
-+err_out_free_ring:
-+	dma_free_coherent(&pdev->dev,
-+		     sizeof (struct tulip_rx_desc) * RX_RING_SIZE +
-+		     sizeof (struct tulip_tx_desc) * TX_RING_SIZE,
-+		     tp->rx_ring, tp->rx_ring_dma);
-+	return -ENODEV;
-+}
-+
-+static int tulip_remove(struct platform_device *pdev)
-+{
-+	struct net_device *dev = platform_get_drvdata (pdev);
-+	struct tulip_private *tp;
-+
-+	if (!dev)
-+		return -ENODEV;
-+
-+	tp = netdev_priv(dev);
-+	unregister_netdev(dev);
-+	dma_free_coherent(&pdev->dev,
-+			     sizeof (struct tulip_rx_desc) * RX_RING_SIZE +
-+			     sizeof (struct tulip_tx_desc) * TX_RING_SIZE,
-+			     tp->rx_ring, tp->rx_ring_dma);
-+	iounmap(tp->base_addr);
-+	free_netdev(dev);
-+	platform_set_drvdata(pdev, NULL);
-+	return 0;
-+}
-+#endif
-+
- #ifdef CONFIG_NET_POLL_CONTROLLER
- /*
-  * Polling 'interrupt' - used by things like netconsole to send skbs
-@@ -2016,6 +2177,17 @@ static struct pci_driver tulip_pci_drive
- };
- #endif
- 
-+#ifdef CONFIG_TULIP_PLATFORM
-+static struct platform_driver tulip_platform_driver = {
-+	.probe = tulip_probe,
-+	.remove = tulip_remove,
-+	.driver = {
-+		.owner = THIS_MODULE,
-+		.name = DRV_NAME,
-+	},
-+};
-+#endif
-+
- 
- static int __init tulip_init (void)
- {
-@@ -2032,6 +2204,9 @@ static int __init tulip_init (void)
- #ifdef CONFIG_TULIP_PCI
- 	ret = pci_register_driver(&tulip_pci_driver);
- #endif
-+#ifdef CONFIG_TULIP_PLATFORM
-+	ret = platform_driver_register(&tulip_platform_driver);
-+#endif
- 	return ret;
- }
- 
-@@ -2041,6 +2216,9 @@ static void __exit tulip_cleanup (void)
- #ifdef CONFIG_TULIP_PCI
- 	pci_unregister_driver (&tulip_pci_driver);
- #endif
-+#ifdef CONFIG_TULIP_PLATFORM
-+	platform_driver_unregister (&tulip_platform_driver);
-+#endif
- }
- 
- 
---- a/drivers/net/ethernet/dec/tulip/tulip.h
-+++ b/drivers/net/ethernet/dec/tulip/tulip.h
-@@ -21,6 +21,8 @@
- #include <linux/timer.h>
- #include <linux/delay.h>
- #include <linux/pci.h>
-+#include <linux/platform_device.h>
-+#include <linux/platform_data/tulip.h>
- #include <asm/io.h>
- #include <asm/irq.h>
- #include <asm/unaligned.h>
-@@ -69,28 +71,6 @@ enum tbl_flag {
- };
- 
- 
--/* chip types.  careful!  order is VERY IMPORTANT here, as these
-- * are used throughout the driver as indices into arrays */
--/* Note 21142 == 21143. */
--enum chips {
--	DC21040 = 0,
--	DC21041 = 1,
--	DC21140 = 2,
--	DC21142 = 3, DC21143 = 3,
--	LC82C168,
--	MX98713,
--	MX98715,
--	MX98725,
--	AX88140,
--	PNIC2,
--	COMET,
--	COMPEX9881,
--	I21145,
--	DM910X,
--	CONEXANT,
--};
--
--
- enum MediaIs {
- 	MediaIsFD = 1,
- 	MediaAlwaysFD = 2,
-@@ -446,7 +426,12 @@ struct tulip_private {
- 	struct mediatable *mtable;
- 	int cur_index;		/* Current media index. */
- 	int saved_if_port;
-+#ifdef CONFIG_TULIP_PCI
- 	struct pci_dev *pdev;
-+#endif
-+#ifdef CONFIG_TULIP_PLATFORM
-+	struct platform_device *pldev;
-+#endif
- 	struct device *kdev;
- 	int irq;
- 	int ttimer;
---- a/drivers/net/ethernet/dec/tulip/interrupt.c
-+++ b/drivers/net/ethernet/dec/tulip/interrupt.c
-@@ -77,6 +77,10 @@ int tulip_refill_rx(struct net_device *d
- 			mapping = pci_map_single(tp->pdev, skb->data, PKT_BUF_SZ,
- 						 PCI_DMA_FROMDEVICE);
- #endif
-+#ifdef CONFIG_TULIP_PLATFORM
-+			mapping = dma_map_single(&tp->pldev->dev, skb->data, PKT_BUF_SZ,
-+						 DMA_FROM_DEVICE);
-+#endif
- 			if (dma_mapping_error(tp->kdev, mapping)) {
- 				dev_kfree_skb(skb);
- 				tp->rx_buffers[entry].skb = NULL;
-@@ -204,8 +208,7 @@ int tulip_poll(struct napi_struct *napi,
- 						dev->stats.rx_fifo_errors++;
-                                }
-                        } else {
--                               struct sk_buff *skb;
--
-+				struct sk_buff *skb;
-                                /* Check if the packet is long enough to accept without copying
-                                   to a minimally-sized skbuff. */
-                                if (pkt_len < tulip_rx_copybreak &&
-@@ -248,6 +251,10 @@ int tulip_poll(struct napi_struct *napi,
-                                        pci_unmap_single(tp->pdev, tp->rx_buffers[entry].mapping,
-                                                         PKT_BUF_SZ, PCI_DMA_FROMDEVICE);
- #endif
-+#ifdef CONFIG_TULIP_PLATFORM
-+				       dma_unmap_single(&tp->pldev->dev, tp->rx_buffers[entry].mapping,
-+						       PKT_BUF_SZ, DMA_FROM_DEVICE);
-+#endif
- 
-                                        tp->rx_buffers[entry].skb = NULL;
-                                        tp->rx_buffers[entry].mapping = 0;
-@@ -641,6 +648,11 @@ irqreturn_t tulip_interrupt(int irq, voi
- 						 tp->tx_buffers[entry].skb->len,
- 						 PCI_DMA_TODEVICE);
- #endif
-+#ifdef CONFIG_TULIP_PLATFORM
-+				dma_unmap_single(&tp->pldev->dev, tp->tx_buffers[entry].mapping,
-+						 tp->tx_buffers[entry].skb->len,
-+						 DMA_TO_DEVICE);
-+#endif
- 
- 				/* Free the original skb. */
- 				dev_kfree_skb_irq(tp->tx_buffers[entry].skb);
---- /dev/null
-+++ b/include/linux/platform_data/tulip.h
-@@ -0,0 +1,31 @@
-+#ifndef _LINUX_TULIP_PDATA_H
-+#define _LINUX_TULIP_PDATA_H
-+
-+/* chip types.  careful!  order is VERY IMPORTANT here, as these
-+ * are used throughout the driver as indices into arrays */
-+/* Note 21142 == 21143. */
-+enum chips {
-+	DC21040 = 0,
-+	DC21041 = 1,
-+	DC21140 = 2,
-+	DC21142 = 3, DC21143 = 3,
-+	LC82C168,
-+	MX98713,
-+	MX98715,
-+	MX98725,
-+	AX88140,
-+	PNIC2,
-+	COMET,
-+	COMPEX9881,
-+	I21145,
-+	DM910X,
-+	CONEXANT,
-+	ADM8668,
-+};
-+
-+struct tulip_platform_data {
-+	u8		mac[6];
-+	enum chips	chip_id;
-+};
-+
-+#endif

target/linux/adm8668/patches-3.14/200-amba_pl010_hacks.patch

@@ -1,377 +0,0 @@
---- a/drivers/tty/serial/amba-pl010.c
-+++ b/drivers/tty/serial/amba-pl010.c
-@@ -49,11 +49,10 @@
- 
- #include <asm/io.h>
- 
--#define UART_NR		8
--
- #define SERIAL_AMBA_MAJOR	204
- #define SERIAL_AMBA_MINOR	16
--#define SERIAL_AMBA_NR		UART_NR
-+#define SERIAL_AMBA_NR		CONFIG_SERIAL_AMBA_PL010_NUMPORTS
-+#define SERIAL_AMBA_NAME	CONFIG_SERIAL_AMBA_PL010_PORTNAME
- 
- #define AMBA_ISR_PASS_LIMIT	256
- 
-@@ -79,9 +78,9 @@ static void pl010_stop_tx(struct uart_po
- 	struct uart_amba_port *uap = (struct uart_amba_port *)port;
- 	unsigned int cr;
- 
--	cr = readb(uap->port.membase + UART010_CR);
-+	cr = __raw_readl(uap->port.membase + UART010_CR);
- 	cr &= ~UART010_CR_TIE;
--	writel(cr, uap->port.membase + UART010_CR);
-+	__raw_writel(cr, uap->port.membase + UART010_CR);
- }
- 
- static void pl010_start_tx(struct uart_port *port)
-@@ -89,9 +88,9 @@ static void pl010_start_tx(struct uart_p
- 	struct uart_amba_port *uap = (struct uart_amba_port *)port;
- 	unsigned int cr;
- 
--	cr = readb(uap->port.membase + UART010_CR);
-+	cr = __raw_readl(uap->port.membase + UART010_CR);
- 	cr |= UART010_CR_TIE;
--	writel(cr, uap->port.membase + UART010_CR);
-+	__raw_writel(cr, uap->port.membase + UART010_CR);
- }
- 
- static void pl010_stop_rx(struct uart_port *port)
-@@ -99,9 +98,9 @@ static void pl010_stop_rx(struct uart_po
- 	struct uart_amba_port *uap = (struct uart_amba_port *)port;
- 	unsigned int cr;
- 
--	cr = readb(uap->port.membase + UART010_CR);
-+	cr = __raw_readl(uap->port.membase + UART010_CR);
- 	cr &= ~(UART010_CR_RIE | UART010_CR_RTIE);
--	writel(cr, uap->port.membase + UART010_CR);
-+	__raw_writel(cr, uap->port.membase + UART010_CR);
- }
- 
- static void pl010_enable_ms(struct uart_port *port)
-@@ -109,18 +108,18 @@ static void pl010_enable_ms(struct uart_
- 	struct uart_amba_port *uap = (struct uart_amba_port *)port;
- 	unsigned int cr;
- 
--	cr = readb(uap->port.membase + UART010_CR);
-+	cr = __raw_readl(uap->port.membase + UART010_CR);
- 	cr |= UART010_CR_MSIE;
--	writel(cr, uap->port.membase + UART010_CR);
-+	__raw_writel(cr, uap->port.membase + UART010_CR);
- }
- 
- static void pl010_rx_chars(struct uart_amba_port *uap)
- {
- 	unsigned int status, ch, flag, rsr, max_count = 256;
- 
--	status = readb(uap->port.membase + UART01x_FR);
-+	status = __raw_readl(uap->port.membase + UART01x_FR);
- 	while (UART_RX_DATA(status) && max_count--) {
--		ch = readb(uap->port.membase + UART01x_DR);
-+		ch = __raw_readl(uap->port.membase + UART01x_DR);
- 		flag = TTY_NORMAL;
- 
- 		uap->port.icount.rx++;
-@@ -129,9 +128,9 @@ static void pl010_rx_chars(struct uart_a
- 		 * Note that the error handling code is
- 		 * out of the main execution path
- 		 */
--		rsr = readb(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX;
-+		rsr = __raw_readl(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX;
- 		if (unlikely(rsr & UART01x_RSR_ANY)) {
--			writel(0, uap->port.membase + UART01x_ECR);
-+			__raw_writel(0, uap->port.membase + UART01x_ECR);
- 
- 			if (rsr & UART01x_RSR_BE) {
- 				rsr &= ~(UART01x_RSR_FE | UART01x_RSR_PE);
-@@ -161,7 +160,7 @@ static void pl010_rx_chars(struct uart_a
- 		uart_insert_char(&uap->port, rsr, UART01x_RSR_OE, ch, flag);
- 
- 	ignore_char:
--		status = readb(uap->port.membase + UART01x_FR);
-+		status = __raw_readl(uap->port.membase + UART01x_FR);
- 	}
- 	spin_unlock(&uap->port.lock);
- 	tty_flip_buffer_push(&uap->port.state->port);
-@@ -174,7 +173,7 @@ static void pl010_tx_chars(struct uart_a
- 	int count;
- 
- 	if (uap->port.x_char) {
--		writel(uap->port.x_char, uap->port.membase + UART01x_DR);
-+		__raw_writel(uap->port.x_char, uap->port.membase + UART01x_DR);
- 		uap->port.icount.tx++;
- 		uap->port.x_char = 0;
- 		return;
-@@ -186,7 +185,7 @@ static void pl010_tx_chars(struct uart_a
- 
- 	count = uap->port.fifosize >> 1;
- 	do {
--		writel(xmit->buf[xmit->tail], uap->port.membase + UART01x_DR);
-+		__raw_writel(xmit->buf[xmit->tail], uap->port.membase + UART01x_DR);
- 		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
- 		uap->port.icount.tx++;
- 		if (uart_circ_empty(xmit))
-@@ -204,9 +203,9 @@ static void pl010_modem_status(struct ua
- {
- 	unsigned int status, delta;
- 
--	writel(0, uap->port.membase + UART010_ICR);
-+	__raw_writel(0, uap->port.membase + UART010_ICR);
- 
--	status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
-+	status = __raw_readl(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
- 
- 	delta = status ^ uap->old_status;
- 	uap->old_status = status;
-@@ -234,7 +233,7 @@ static irqreturn_t pl010_int(int irq, vo
- 
- 	spin_lock(&uap->port.lock);
- 
--	status = readb(uap->port.membase + UART010_IIR);
-+	status = __raw_readl(uap->port.membase + UART010_IIR);
- 	if (status) {
- 		do {
- 			if (status & (UART010_IIR_RTIS | UART010_IIR_RIS))
-@@ -247,7 +246,7 @@ static irqreturn_t pl010_int(int irq, vo
- 			if (pass_counter-- == 0)
- 				break;
- 
--			status = readb(uap->port.membase + UART010_IIR);
-+			status = __raw_readl(uap->port.membase + UART010_IIR);
- 		} while (status & (UART010_IIR_RTIS | UART010_IIR_RIS |
- 				   UART010_IIR_TIS));
- 		handled = 1;
-@@ -261,7 +260,7 @@ static irqreturn_t pl010_int(int irq, vo
- static unsigned int pl010_tx_empty(struct uart_port *port)
- {
- 	struct uart_amba_port *uap = (struct uart_amba_port *)port;
--	unsigned int status = readb(uap->port.membase + UART01x_FR);
-+	unsigned int status = __raw_readl(uap->port.membase + UART01x_FR);
- 	return status & UART01x_FR_BUSY ? 0 : TIOCSER_TEMT;
- }
- 
-@@ -271,7 +270,7 @@ static unsigned int pl010_get_mctrl(stru
- 	unsigned int result = 0;
- 	unsigned int status;
- 
--	status = readb(uap->port.membase + UART01x_FR);
-+	status = __raw_readl(uap->port.membase + UART01x_FR);
- 	if (status & UART01x_FR_DCD)
- 		result |= TIOCM_CAR;
- 	if (status & UART01x_FR_DSR)
-@@ -297,12 +296,12 @@ static void pl010_break_ctl(struct uart_
- 	unsigned int lcr_h;
- 
- 	spin_lock_irqsave(&uap->port.lock, flags);
--	lcr_h = readb(uap->port.membase + UART010_LCRH);
-+	lcr_h = __raw_readl(uap->port.membase + UART010_LCRH);
- 	if (break_state == -1)
- 		lcr_h |= UART01x_LCRH_BRK;
- 	else
- 		lcr_h &= ~UART01x_LCRH_BRK;
--	writel(lcr_h, uap->port.membase + UART010_LCRH);
-+	__raw_writel(lcr_h, uap->port.membase + UART010_LCRH);
- 	spin_unlock_irqrestore(&uap->port.lock, flags);
- }
- 
-@@ -330,12 +329,12 @@ static int pl010_startup(struct uart_por
- 	/*
- 	 * initialise the old status of the modem signals
- 	 */
--	uap->old_status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
-+	uap->old_status = __raw_readl(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
- 
- 	/*
- 	 * Finally, enable interrupts
- 	 */
--	writel(UART01x_CR_UARTEN | UART010_CR_RIE | UART010_CR_RTIE,
-+	__raw_writel(UART01x_CR_UARTEN | UART010_CR_RIE | UART010_CR_RTIE,
- 	       uap->port.membase + UART010_CR);
- 
- 	return 0;
-@@ -358,10 +357,10 @@ static void pl010_shutdown(struct uart_p
- 	/*
- 	 * disable all interrupts, disable the port
- 	 */
--	writel(0, uap->port.membase + UART010_CR);
-+	__raw_writel(0, uap->port.membase + UART010_CR);
- 
- 	/* disable break condition and fifos */
--	writel(readb(uap->port.membase + UART010_LCRH) &
-+	__raw_writel(__raw_readl(uap->port.membase + UART010_LCRH) &
- 		~(UART01x_LCRH_BRK | UART01x_LCRH_FEN),
- 	       uap->port.membase + UART010_LCRH);
- 
-@@ -383,7 +382,7 @@ pl010_set_termios(struct uart_port *port
- 	/*
- 	 * Ask the core to calculate the divisor for us.
- 	 */
--	baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16); 
-+	baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16);
- 	quot = uart_get_divisor(port, baud);
- 
- 	switch (termios->c_cflag & CSIZE) {
-@@ -446,25 +445,25 @@ pl010_set_termios(struct uart_port *port
- 		uap->port.ignore_status_mask |= UART_DUMMY_RSR_RX;
- 
- 	/* first, disable everything */
--	old_cr = readb(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE;
-+	old_cr = __raw_readl(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE;
- 
- 	if (UART_ENABLE_MS(port, termios->c_cflag))
- 		old_cr |= UART010_CR_MSIE;
- 
--	writel(0, uap->port.membase + UART010_CR);
-+	__raw_writel(0, uap->port.membase + UART010_CR);
- 
- 	/* Set baud rate */
- 	quot -= 1;
--	writel((quot & 0xf00) >> 8, uap->port.membase + UART010_LCRM);
--	writel(quot & 0xff, uap->port.membase + UART010_LCRL);
-+	__raw_writel((quot & 0xf00) >> 8, uap->port.membase + UART010_LCRM);
-+	__raw_writel(quot & 0xff, uap->port.membase + UART010_LCRL);
- 
- 	/*
- 	 * ----------v----------v----------v----------v-----
- 	 * NOTE: MUST BE WRITTEN AFTER UARTLCR_M & UARTLCR_L
- 	 * ----------^----------^----------^----------^-----
- 	 */
--	writel(lcr_h, uap->port.membase + UART010_LCRH);
--	writel(old_cr, uap->port.membase + UART010_CR);
-+	__raw_writel(lcr_h, uap->port.membase + UART010_LCRH);
-+	__raw_writel(old_cr, uap->port.membase + UART010_CR);
- 
- 	spin_unlock_irqrestore(&uap->port.lock, flags);
- }
-@@ -546,7 +545,7 @@ static struct uart_ops amba_pl010_pops =
- 	.verify_port	= pl010_verify_port,
- };
- 
--static struct uart_amba_port *amba_ports[UART_NR];
-+static struct uart_amba_port *amba_ports[SERIAL_AMBA_NR];
- 
- #ifdef CONFIG_SERIAL_AMBA_PL010_CONSOLE
- 
-@@ -556,10 +555,10 @@ static void pl010_console_putchar(struct
- 	unsigned int status;
- 
- 	do {
--		status = readb(uap->port.membase + UART01x_FR);
-+		status = __raw_readl(uap->port.membase + UART01x_FR);
- 		barrier();
- 	} while (!UART_TX_READY(status));
--	writel(ch, uap->port.membase + UART01x_DR);
-+	__raw_writel(ch, uap->port.membase + UART01x_DR);
- }
- 
- static void
-@@ -573,8 +572,8 @@ pl010_console_write(struct console *co, 
- 	/*
- 	 *	First save the CR then disable the interrupts
- 	 */
--	old_cr = readb(uap->port.membase + UART010_CR);
--	writel(UART01x_CR_UARTEN, uap->port.membase + UART010_CR);
-+	old_cr = __raw_readl(uap->port.membase + UART010_CR);
-+	__raw_writel(UART01x_CR_UARTEN, uap->port.membase + UART010_CR);
- 
- 	uart_console_write(&uap->port, s, count, pl010_console_putchar);
- 
-@@ -583,10 +582,10 @@ pl010_console_write(struct console *co, 
- 	 *	and restore the TCR
- 	 */
- 	do {
--		status = readb(uap->port.membase + UART01x_FR);
-+		status = __raw_readl(uap->port.membase + UART01x_FR);
- 		barrier();
- 	} while (status & UART01x_FR_BUSY);
--	writel(old_cr, uap->port.membase + UART010_CR);
-+	__raw_writel(old_cr, uap->port.membase + UART010_CR);
- 
- 	clk_disable(uap->clk);
- }
-@@ -595,9 +594,9 @@ static void __init
- pl010_console_get_options(struct uart_amba_port *uap, int *baud,
- 			     int *parity, int *bits)
- {
--	if (readb(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) {
-+	if (__raw_readl(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) {
- 		unsigned int lcr_h, quot;
--		lcr_h = readb(uap->port.membase + UART010_LCRH);
-+		lcr_h = __raw_readl(uap->port.membase + UART010_LCRH);
- 
- 		*parity = 'n';
- 		if (lcr_h & UART01x_LCRH_PEN) {
-@@ -612,8 +611,8 @@ pl010_console_get_options(struct uart_am
- 		else
- 			*bits = 8;
- 
--		quot = readb(uap->port.membase + UART010_LCRL) |
--		       readb(uap->port.membase + UART010_LCRM) << 8;
-+		quot = __raw_readl(uap->port.membase + UART010_LCRL) |
-+		       __raw_readl(uap->port.membase + UART010_LCRM) << 8;
- 		*baud = uap->port.uartclk / (16 * (quot + 1));
- 	}
- }
-@@ -632,7 +631,7 @@ static int __init pl010_console_setup(st
- 	 * if so, search for the first available port that does have
- 	 * console support.
- 	 */
--	if (co->index >= UART_NR)
-+	if (co->index >= SERIAL_AMBA_NR)
- 		co->index = 0;
- 	uap = amba_ports[co->index];
- 	if (!uap)
-@@ -654,7 +653,7 @@ static int __init pl010_console_setup(st
- 
- static struct uart_driver amba_reg;
- static struct console amba_console = {
--	.name		= "ttyAM",
-+	.name		= SERIAL_AMBA_NAME,
- 	.write		= pl010_console_write,
- 	.device		= uart_console_device,
- 	.setup		= pl010_console_setup,
-@@ -670,11 +669,11 @@ static struct console amba_console = {
- 
- static struct uart_driver amba_reg = {
- 	.owner			= THIS_MODULE,
--	.driver_name		= "ttyAM",
--	.dev_name		= "ttyAM",
-+	.driver_name		= SERIAL_AMBA_NAME,
-+	.dev_name		= SERIAL_AMBA_NAME,
- 	.major			= SERIAL_AMBA_MAJOR,
- 	.minor			= SERIAL_AMBA_MINOR,
--	.nr			= UART_NR,
-+	.nr			= SERIAL_AMBA_NR,
- 	.cons			= AMBA_CONSOLE,
- };
- 
---- a/drivers/tty/serial/Kconfig
-+++ b/drivers/tty/serial/Kconfig
-@@ -18,10 +18,25 @@ config SERIAL_AMBA_PL010
- 	help
- 	  This selects the ARM(R) AMBA(R) PrimeCell PL010 UART.  If you have
- 	  an Integrator/AP or Integrator/PP2 platform, or if you have a
--	  Cirrus Logic EP93xx CPU, say Y or M here.
-+	  Cirrus Logic EP93xx CPU or an Infineon ADM5120 SOC, say Y or M here.
- 
- 	  If unsure, say N.
- 
-+config SERIAL_AMBA_PL010_NUMPORTS
-+	int "Maximum number of AMBA PL010 serial ports"
-+	depends on SERIAL_AMBA_PL010
-+	default "8"
-+	---help---
-+	  Set this to the number of serial ports you want the AMBA PL010 driver
-+	  to support.
-+
-+config SERIAL_AMBA_PL010_PORTNAME
-+	string "Name of the AMBA PL010 serial ports"
-+	depends on SERIAL_AMBA_PL010
-+	default "ttyAM"
-+	---help---
-+	  ::: To be written :::
-+
- config SERIAL_AMBA_PL010_CONSOLE
- 	bool "Support for console on AMBA serial port"
- 	depends on SERIAL_AMBA_PL010=y

target/linux/adm8668/patches-3.14/201-amba_bus_hacks.patch

@@ -1,13 +0,0 @@
---- a/drivers/amba/bus.c
-+++ b/drivers/amba/bus.c
-@@ -20,6 +20,10 @@
- 
- #include <asm/irq.h>
- 
-+#ifndef NO_IRQ
-+#define NO_IRQ		(-1)
-+#endif
-+
- #define to_amba_driver(d)	container_of(d, struct amba_driver, drv)
- 
- static const struct amba_id *