ath79: initial gl-ar300m support

Signed-off-by: Marty E. Plummer <[email protected]>

target/linux/ath79/base-files/etc/board.d/02_network

@@ -28,6 +28,11 @@ ath79_setup_interfaces()
 	"glinet,ar150")
 		ucidef_set_interfaces_lan_wan "eth1" "eth0"
 		;;
+
+	"glinet,ar300m")
+		ucidef_set_interfaces_lan_wan "eth1" "eth0"
+		;;
+
 	"tplink,tl-mr3020-v1")
 		ucidef_set_interface_lan "eth0.1"
 		ucidef_add_switch "switch0" "0@eth0" "1:lan"

target/linux/ath79/dts/qca9533.dtsi

@@ -0,0 +1,235 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+#include <dt-bindings/clock/ath79-clk.h>
+#include "ath79.dtsi"
+
+/ {
+	compatible = "qca,qca9533";
+
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "mips,mips24Kc";
+			clocks = <&pll ATH79_CLK_CPU>;
+			reg = <0>;
+		};
+	};
+
+	ref: ref {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+	};
+
+	ahb {
+		apb {
+			ddr_ctrl: memory-controller@18000000 {
+				compatible = "qca,ar9530-ddr-controller",
+						"qca,ar7240-ddr-controller";
+				reg = <0x18000000 0x128>;
+
+				#qca,ddr-wb-channel-cells = <1>;
+			};
+
+			uart: uart@18020000 {
+				compatible = "ns16550a";
+				reg = <0x18020000 0x20>;
+
+				interrupts = <3>;
+
+				clocks = <&pll ATH79_CLK_REF>;
+				clock-names = "uart";
+
+				reg-io-width = <4>;
+				reg-shift = <2>;
+				no-loopback-test;
+
+				status = "disabled";
+			};
+
+			usb_phy: usb-phy@18030000 {
+				compatible = "qca,ar7200-usb-phy";
+				reg = <0x18030000 0x100>;
+				#phy-cells = <0>;
+
+				reset-names = "usb-phy", "usb-suspend-override";
+				resets = <&rst 4>, <&rst 3>;
+
+				status = "disabled";
+			};
+
+			gpio: gpio@18040000 {
+				compatible = "qca,ar9530-gpio",
+						"qca,ar9340-gpio";
+				reg = <0x18040000 0x28>;
+
+				interrupts = <2>;
+				ngpios = <20>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			pinmux: pinmux@1804002c {
+				compatible = "pinctrl-single";
+
+				reg = <0x1804002c 0x48>;
+
+				#size-cells = <0>;
+
+				pinctrl-single,bit-per-mux;
+				pinctrl-single,register-width = <32>;
+				pinctrl-single,function-mask = <0x1>;
+				#pinctrl-cells = <2>;
+
+				jtag_disable_pins: pinmux_jtag_disable_pins {
+					pinctrl-single,bits = <
+						0x40 0x2 0x2
+						>;
+				};
+			};
+
+			pll: pll-controller@18050000 {
+				compatible = "qca,qca9530-pll", "syscon";
+				reg = <0x18050000 0x48>;
+
+				#clock-cells = <1>;
+				clocks = <&ref>;
+				clock-names = "ref";
+				clock-output-names = "cpu", "ddr", "ahb";
+			};
+
+			wdt: wdt@18060008 {
+				compatible = "qca,qca9530-wdt", "qca,ar7130-wdt";
+				reg = <0x18060008 0x8>;
+
+				interrupts = <4>;
+
+				clocks = <&pll ATH79_CLK_AHB>;
+				clock-names = "wdt";
+			};
+
+			rst: reset-controller@1806001c {
+				compatible = "qca,qca9530-reset",
+						"qca,ar7100-reset";
+				reg = <0x1806001c 0xac>;
+
+				#reset-cells = <1>;
+
+				intc2: interrupt-controller@2 {
+					compatible = "qcom,qca9556-intc";
+
+					interrupts = <2>;
+
+					interrupt-controller;
+					#interrupt-cells = <1>;
+
+					qcom,pending-bits = <0x1f0>,	/* pcie rc1 */
+							    <0xf>;	/* wmac */
+				};
+			};
+
+			pcie0: pcie-controller@180c0000 {
+				compatible = "qcom,ar7240-pci";
+				#address-cells = <3>;
+				#size-cells = <2>;
+				bus-range = <0x0 0x0>;
+				reg = <0x180c0000 0x1000>, /* CRP */
+				      <0x180f0000 0x100>,  /* CTRL */
+				      <0x14000000 0x1000>; /* CFG */
+				reg-names = "crp_base", "ctrl_base", "cfg_base";
+				ranges = <0x2000000 0 0x10000000 0x10000000 0 0x04000000	/* pci memory */
+					  0x1000000 0 0x00000000 0x0000000 0 0x000001>;		/* io space */
+				interrupt-parent = <&intc2>;
+				interrupts = <0>;
+
+				interrupt-controller;
+				#interrupt-cells = <1>;
+
+				interrupt-map-mask = <0 0 0 1>;
+				interrupt-map = <0 0 0 0 &pcie0 0>;
+				status = "disabled";
+			};
+
+			wmac: gmac@18100000 {
+				compatible = "qca,qca9530-wmac";
+				reg = <0x18100000 0x230000>;
+
+				interrupt-parent = <&cpuintc>;
+				interrupts = <2>;
+
+				status = "disabled";
+			};
+		};
+
+		usb0: usb@1b000000 {
+			compatible = "generic-ehci";
+			reg = <0x1b000000 0x1000>;
+
+			interrupts = <3>;
+			resets = <&rst 5>;
+			reset-names = "usb-host";
+			dr_mode = "host";
+
+			has-transaction-translator;
+			caps-offset = <0x100>;
+
+			phy-names = "usb-phy";
+			phys = <&usb_phy>;
+
+			status = "disabled";
+		};
+
+		spi: spi@1f000000 {
+			compatible = "qca,ar9530-spi", "qca,ar7100-spi";
+			reg = <0x1f000000 0x10>;
+
+			clocks = <&pll ATH79_CLK_AHB>;
+			clock-names = "ahb";
+
+			status = "disabled";
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+	};
+
+};
+
+&mdio0 {
+	resets = <&rst 22>;
+	reset-names = "mdio";
+};
+
+&eth0 {
+	compatible = "qca,qca9530-eth", "syscon";
+	pll-data = <0x82000101 0x80000101 0x80001313>;
+	reg = <0x19000000 0x200
+		0x18070000 0x4>;
+	pll-reg = <0x4 0x2c 17>;
+	pll-handle = <&pll>;
+
+	reset-names = "mac";
+	resets = <&rst 9>;
+};
+
+
+&mdio1 {
+	resets = <&rst 23>;
+	reset-names = "mdio";
+	builtin-switch;
+};
+
+&eth1 {
+	compatible = "qca,qca9530-eth", "syscon";
+	resets = <&rst 13>;
+	reset-names = "mac";
+};

target/linux/ath79/dts/qca9533_glinet_ar300m.dtsi

@@ -0,0 +1,141 @@
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca9533.dtsi"
+
+/ {
+	compatible = "glinet,ar300m", "qca,qca9533";
+	model = "GL.iNet GL-AR300M";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x8000000>;
+	};
+
+	extosc: ref {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-output-names = "ref";
+		clock-frequency = <25000000>;
+	};
+
+	keys {
+		compatible = "gpio-keys-polled";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <20>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&jtag_disable_pins>;
+
+		button@0 {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+		};
+
+		button@1 {
+			label = "button right";
+			linux,code = <BTN_0>;
+			gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
+		};
+
+		button@3 {
+			label = "button left";
+			linux,code = <BTN_1>;
+			gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		usb {
+			label = "gl-ar300m:green:usb";
+			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&hub_port>;
+			linux,default-trigger = "usbport";
+		};
+
+		wlan {
+			label = "gl-ar300m:green:wlan";
+			gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0tpt";
+		};
+
+		lan {
+			label = "gl-ar300m:green:lan";
+			gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+		};
+
+		status {
+			label = "gl-ar300m:green:status";
+			gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&uart {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+
+	hub_port: port@1 {
+		reg = <1>;
+		#trigger-soruce-cells = <0>;
+	};
+};
+
+&usb_phy {
+	status = "okay";
+};
+
+&pll {
+	clocks = <&extosc>;
+};
+
+&mdio0 {
+	status = "okay";
+
+	phy4: ethernet-phy@4 {
+		reg = <4>;
+		phy-mode = "mii";
+	};
+};
+
+&mdio1 {
+	status = "okay";
+};
+
+&eth0 {
+	status = "okay";
+
+	mtd-mac-address = <&art 0x0>;
+	phy-handle = <&phy4>;
+	phy-mode = "mii";
+};
+
+&eth1 {
+	status = "okay";
+
+	mtd-mac-address = <&art 0x6>;
+	phy-mode = "gmii";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&wmac {
+	status = "okay";
+	mtd-cal-data = <&art 0x1000>;
+	mtd-mac-address = <&art 0x1002>;
+};

target/linux/ath79/dts/qca9533_glinet_ar300m_nor.dts

@@ -0,0 +1,46 @@
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca9533_glinet_ar300m.dtsi"
+
+&spi {
+	status = "okay";
+	num-cs = <0>;
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "winbond,w25q128", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <25000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0x000000 0x040000>;
+				read-only;
+			};
+
+			partition@1 {
+				label = "u-boot-env";
+				reg = <0x040000 0x010000>;
+			};
+
+			partition@2 {
+				label = "firmware";
+				reg = <0x050000 0xfa0000>;
+			};
+
+			art: partition@3 {
+				label = "art";
+				reg = <0xff0000 0x010000>;
+			};
+		};
+	};
+};

target/linux/ath79/image/generic.mk

@@ -40,6 +40,15 @@ define Device/glinet_ar150
 endef
 TARGET_DEVICES += glinet_ar150
 
+define Device/glinet_ar300m_nor
+  ATH_SOC := qca9533
+  DEVICE_TITLE := GL.iNet GL-AR300M
+  DEVICE_PACKAGES := kmod-usb-core kmod-usb2
+  IMAGE_SIZE := 16000k
+  SUPPORTED_DEVICES += gl-ar300m
+endef
+TARGET_DEVICES += glinet_ar300m_nor
+
 define Device/openmesh_om5p-ac-v2
   ATH_SOC := qca9558
   DEVICE_TITLE := OpenMesh OM5P-AC v2