ipq40xx: add support for GL.iNet GL-B2200

This patch adds supports for the GL-B2200 router.

Specifications:
  - SOC: Qualcomm IPQ4019 ARM Quad-Core
  - RAM: 512 MiB
  - Flash: 16 MiB NOR - SPI0
  - EMMC: 8GB EMMC
  - ETH: Qualcomm QCA8075
  - WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11b/g/n 2x2
  - WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11n/ac W2 2x2
  - WLAN3: Qualcomm Atheros QCA9886 5GHz 802.11n/ac W2 2x2
  - INPUT: Reset, WPS
  - LED: Power, Internet
  - UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
  - UART2: On board with BLE module
  - SPI1: On board socket for Zigbee module

Update firmware instructions:
Please update the firmware via U-Boot web UI (by default at 192.168.1.1, following instructions found at
https://docs.gl-inet.com/en/3/troubleshooting/debrick/).
Normal sysupgrade, either via CLI or LuCI, is not possible from stock firmware.
Please do use the *gl-b2200-squashfs-emmc.img file, gunzipping the produced *gl-b2200-squashfs-emmc.img.gz one first.

What's working:
- WiFi 2G, 5G
- WPA2/WPA3

Not tested:
- Bluetooth LE/Zigbee

Credits goes to the original authors of this patch.

V1->V2:
- updates *arm-boot-add-dts-files.patch correctly (sorry, my mistake)
- add uboot-envtools support
V2->V3:
- Li Zhang updated official patch to fix wrong MAC address on wlan0 (PCI) interface
V3->V4:
- wire up sysupgrade

Signed-off-by: Li Zhang <[email protected]>
[fix tab and trailing space, document what's working and what's not]
Signed-off-by: TruongSinh Tran-Nguyen <[email protected]>
[rebase on top of master, address remaining comments]
Signed-off-by: Enrico Mioso <[email protected]>
[remove redundant check in platform.sh]
Signed-off-by: Daniel Golle <[email protected]>

package/boot/uboot-envtools/files/ipq40xx

@@ -35,6 +35,7 @@ devolo,magic-2-wifi-next|\
 edgecore,ecw5211|\
 glinet,gl-ap1300|\
 glinet,gl-b1300|\
+glinet,gl-b2200|\
 luma,wrtq-329acn|\
 netgear,wac510|\
 openmesh,a42|\

package/firmware/ipq-wifi/Makefile

@@ -39,6 +39,7 @@ ALLWIFIBOARDS:= \
 	engenius_emr3500 \
 	ezviz_cs-w3-wd1200g-eup \
 	glinet_gl-ap1300 \
+	glinet_gl-b2200 \
 	glinet_gl-s1300 \
 	linksys_ea8300 \
 	linksys_mr8300-v0 \
@@ -127,6 +128,7 @@ $(eval $(call generate-ipq-wifi-package,engenius_emd1,EnGenius EMD1))
 $(eval $(call generate-ipq-wifi-package,engenius_emr3500,EnGenius EMR3500))
 $(eval $(call generate-ipq-wifi-package,ezviz_cs-w3-wd1200g-eup,EZVIZ CS-W3-WD1200G EUP))
 $(eval $(call generate-ipq-wifi-package,glinet_gl-ap1300,GL.iNet GL-AP1300))
+$(eval $(call generate-ipq-wifi-package,glinet_gl-b2200,GL.iNet GL-B2200))
 $(eval $(call generate-ipq-wifi-package,glinet_gl-s1300,GL.iNet GL-S1300))
 $(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300))
 $(eval $(call generate-ipq-wifi-package,linksys_mr8300-v0,Linksys MR8300))

target/linux/ipq40xx/base-files/etc/board.d/02_network

@@ -106,6 +106,11 @@ ipq40xx_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"0u@eth0" "3:lan" "4:lan"
 		;;
+	glinet,gl-b2200)
+		ucidef_set_interfaces_lan_wan "eth0" "eth1"
+		ucidef_add_switch "switch0" \
+			"0u@eth0" "1:lan" "2:lan" "3:lan" "5:lan" "0u@eth1" "4:wan"
+		;;
 	mobipromo,cm520-79f)
 		ucidef_add_switch "switch0" \
 			"0u@eth0" "3:lan:2" "4:lan:1"

target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata

@@ -9,6 +9,9 @@ board=$(board_name)
 case "$FIRMWARE" in
 "ath10k/cal-pci-0000:01:00.0.bin")
 	case "$board" in
+	glinet,gl-b2200)
+		caldata_extract "ART" 0x9000 0x2f20
+		;;
 	meraki,mr33)
 		caldata_extract_ubi "ART" 0x9000 0x844
 		caldata_valid "4408" || caldata_extract "ART" 0x9000 0x844
@@ -64,6 +67,7 @@ case "$FIRMWARE" in
 	ezviz,cs-w3-wd1200g-eup |\
 	glinet,gl-ap1300 |\
 	glinet,gl-b1300 |\
+	glinet,gl-b2200 |\
 	glinet,gl-s1300 |\
 	linksys,ea6350v3 |\
 	mobipromo,cm520-79f |\
@@ -186,6 +190,7 @@ case "$FIRMWARE" in
 	ezviz,cs-w3-wd1200g-eup |\
 	glinet,gl-ap1300 |\
 	glinet,gl-b1300 |\
+	glinet,gl-b2200 |\
 	glinet,gl-s1300 |\
 	linksys,ea6350v3 |\
 	mobipromo,cm520-79f |\

target/linux/ipq40xx/base-files/lib/upgrade/platform.sh

@@ -96,6 +96,12 @@ platform_do_upgrade() {
 	qxwlan,e2600ac-c2)
 		nand_do_upgrade "$1"
 		;;
+	glinet,gl-b2200)
+		CI_KERNPART="0:HLOS"
+		CI_ROOTPART="rootfs"
+		CI_DATAPART="rootfs_data"
+		emmc_do_upgrade "$1"
+		;;
 	alfa-network,ap120c-ac)
 		part="$(awk -F 'ubi.mtd=' '{printf $2}' /proc/cmdline | sed -e 's/ .*$//')"
 		if [ "$part" = "rootfs1" ]; then
@@ -166,3 +172,12 @@ platform_do_upgrade() {
 		;;
 	esac
 }
+
+platform_copy_config() {
+	case "$(board_name)" in
+	glinet,gl-b2200)
+		emmc_copy_config
+		;;
+	esac
+	return 0;
+}

target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-gl-b2200.dts

@@ -0,0 +1,364 @@
+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+	model = "GL.iNet GL-B2200";
+	compatible = "glinet,gl-b2200", "qcom,ipq4019";
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>;
+	};
+
+	chosen {
+		bootargs-append = " root=/dev/mmcblk0p2 rw rootwait clk_ignore_unused";
+	};
+
+	soc {
+		rng@22000 {
+			status = "okay";
+		};
+
+		mdio@90000 {
+			status = "okay";
+		};
+
+		ess-psgmii@98000 {
+			status = "okay";
+		};
+
+		tcsr@1949000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1949000 0x100>;
+			qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+		};
+
+		tcsr@194b000 {
+			/* select hostmode */
+			compatible = "qcom,tcsr";
+			reg = <0x194b000 0x100>;
+			qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+			status = "okay";
+		};
+
+		ess_tcsr@1953000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1953000 0x1000>;
+			qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+		};
+
+		tcsr@1957000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1957000 0x100>;
+			qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+		};
+
+		crypto@8e3a000 {
+			status = "okay";
+		};
+
+		ess-switch@c000000 {
+			status = "okay";
+			switch_lan_bmp = <0x2e>;
+			switch_wan_bmp = <0x10>;
+		};
+
+		edma@c080000 {
+			status = "okay";
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		wps {
+			label = "wps";
+			gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+			linux,input-type = <1>;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&tlmm 43 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+			linux,input-type = <1>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		power_blue {
+			label = "blue:power";
+			gpios = <&tlmm 57 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+		internet_blue {
+			label = "blue:internet";
+			gpios = <&tlmm 60 GPIO_ACTIVE_HIGH>;
+		};
+		power_white {
+			label = "white:power";
+			gpios = <&tlmm 61 GPIO_ACTIVE_LOW>;
+		};
+		internet_white {
+			label = "white:internet";
+			gpios = <&tlmm 66 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&gmac1 {
+	qcom,phy_mdio_addr = <3>;
+	qcom,poll_required = <1>;
+	qcom,forced_speed = <1000>;
+	qcom,forced_duplex = <1>;
+	vlan_tag = <2 0x10>;
+};
+
+&gmac0 {
+	vlan_tag = <1 0x2e>;
+};
+
+&vqmmc {
+	status = "okay";
+};
+
+&sdhci {
+	status = "okay";
+	pinctrl-0 = <&sd_pins>;
+	pinctrl-names = "default";
+	cd-gpios = <&tlmm 3 GPIO_ACTIVE_LOW>;
+	vqmmc-supply = <&vqmmc>;
+};
+
+&blsp_dma {
+	status = "okay";
+};
+
+&cryptobam {
+	status = "okay";
+};
+
+&blsp1_spi1 {
+	pinctrl-0 = <&spi_0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <24000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "SBL1";
+				reg = <0x0 0x40000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "MIBIB";
+				reg = <0x40000 0x20000>;
+				read-only;
+			};
+
+			partition@60000 {
+				label = "QSEE";
+				reg = <0x60000 0x60000>;
+				read-only;
+			};
+
+			partition@c0000 {
+				label = "CDT";
+				reg = <0xc0000 0x10000>;
+				read-only;
+			};
+
+			partition@d0000 {
+				label = "DDRPARAMS";
+				reg = <0xd0000 0x10000>;
+				read-only;
+			};
+
+			partition@e0000 {
+				label = "APPSBLENV";
+				reg = <0xe0000 0x10000>;
+				read-only;
+			};
+
+			partition@f0000 {
+				label = "APPSBL";
+				reg = <0xf0000 0x80000>;
+				read-only;
+			};
+
+			partition@170000 {
+				label = "ART";
+				reg = <0x170000 0x10000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&blsp1_spi2 {
+	pinctrl-0 = <&spi_1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	spidev1: spi@0 {
+		compatible = "siliconlabs,si3210";
+		reg = <0>;
+		spi-max-frequency = <24000000>;
+	};
+};
+
+&blsp1_uart1 {
+	pinctrl-0 = <&serial_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&blsp1_uart2 {
+	pinctrl-0 = <&serial_1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&tlmm {
+	serial_pins: serial_pinmux {
+		mux {
+			pins = "gpio16", "gpio17";
+			function = "blsp_uart0";
+			bias-disable;
+		};
+	};
+
+	serial_1_pins: serial1_pinmux {
+		mux {
+			pins = "gpio8", "gpio9",
+				"gpio10", "gpio11";
+			function = "blsp_uart1";
+			bias-disable;
+		};
+	};
+
+	spi_0_pins: spi_0_pinmux {
+		pinmux {
+			function = "blsp_spi0";
+			pins = "gpio13", "gpio14", "gpio15";
+		};
+		pinmux_cs {
+			function = "gpio";
+			pins = "gpio12";
+		};
+		pinconf {
+			pins = "gpio13", "gpio14", "gpio15";
+			drive-strength = <12>;
+			bias-disable;
+		};
+		pinconf_cs {
+			pins = "gpio12";
+			drive-strength = <2>;
+			bias-disable;
+			output-high;
+		};
+	};
+
+	spi_1_pins: spi_1_pinmux {
+		mux {
+			pins = "gpio44", "gpio46", "gpio47";
+			function = "blsp_spi1";
+			bias-disable;
+		};
+		cs {
+			pins = "gpio45";
+			function = "gpio";
+			bias-pull-up;
+		};
+		reset {
+			pins = "gpio43";
+			function = "gpio";
+			output-high;
+		};
+		mux_2 {
+			pins = "gpio35";
+			function = "gpio";
+			output-high;
+		};
+		host_int {
+			pins = "gpio2";
+			function = "gpio";
+			input;
+		};
+		wake {
+			pins = "gpio48";
+			function = "gpio";
+			output-high;
+		};
+	};
+
+	sd_pins: sd_pins {
+		pinmux {
+			function = "sdio";
+			pins = "gpio23", "gpio24", "gpio25", "gpio26",
+				"gpio29", "gpio30", "gpio31", "gpio32";
+			drive-strength = <10>;
+		};
+
+		pinmux_sd_clk {
+			function = "sdio";
+			pins = "gpio27";
+			drive-strength = <16>;
+		};
+
+		pinmux_sd7 {
+			function = "sdio";
+			pins = "gpio28";
+			drive-strength = <10>;
+			bias-disable;
+		};
+	};
+
+};
+
+&pcie0 {
+	status = "okay";
+	perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
+	wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
+
+	bridge@0,0 {
+		reg = <0x00000000 0 0 0 0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		ranges;
+
+		wifi2: wifi@1,0 {
+			status = "okay";
+			compatible = "qcom,ath10k";
+			reg = <0x00010000 0 0 0 0>;
+			qcom,ath10k-calibration-variant = "GL-B2200";
+		};
+	};
+};
+
+&wifi0 {
+	status = "okay";
+	qcom,ath10k-calibration-variant = "GL-B2200";
+};
+
+&wifi1 {
+	status = "okay";
+	qcom,ath10k-calibration-variant = "GL-B2200";
+};

target/linux/ipq40xx/generic/target.mk

@@ -1 +1,2 @@
 BOARDNAME:=Generic
+FEATURES+=emmc

target/linux/ipq40xx/image/generic.mk

@@ -92,6 +92,16 @@ define Build/qsdk-ipq-factory-nand-askey
 	@mv [email protected] $@
 endef
 
+define Build/qsdk-ipq-app-gpt
+	cp $@ [email protected] 2>/dev/null || true
+	ptgen -g -o [email protected] -a 1 -l 1024 \
+			-t 0x2e -N 0:HLOS -r -p 32M \
+			-t 0x83 -N rootfs -r -p 128M \
+				-N rootfs_data -p 512M
+	cat [email protected] >> $@
+	rm [email protected]
+endef
+
 define Build/SenaoFW
 	-$(STAGING_DIR_HOST)/bin/mksenaofw \
 		-n $(BOARD_NAME) -r $(VENDOR_ID) -p $(1) \
@@ -520,6 +530,24 @@ define Device/glinet_gl-b1300
 endef
 TARGET_DEVICES += glinet_gl-b1300
 
+define Device/glinet_gl-b2200
+	$(call Device/FitzImage)
+	DEVICE_VENDOR := GL.iNet
+	DEVICE_MODEL := GL-B2200
+	SOC := qcom-ipq4019
+	DEVICE_DTS_CONFIG := [email protected]
+	KERNEL_INITRAMFS_SUFFIX := -recovery.itb
+	IMAGES := emmc.img.gz sysupgrade.bin
+	IMAGE/emmc.img.gz := qsdk-ipq-app-gpt |\
+		pad-to 1024k | append-kernel |\
+		pad-to 33792k | append-rootfs |\
+		append-metadata | gzip
+	IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+	DEVICE_PACKAGES := ath10k-firmware-qca9888-ct ipq-wifi-glinet_gl-b2200 \
+		kmod-fs-ext4 kmod-mmc kmod-spi-dev mkf2fs e2fsprogs kmod-fs-f2fs
+endef
+TARGET_DEVICES += glinet_gl-b2200
+
 define Device/glinet_gl-s1300
 	$(call Device/FitzImage)
 	DEVICE_VENDOR := GL.iNet

target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch

@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <[email protected]>
 
 --- a/arch/arm/boot/dts/Makefile
 +++ b/arch/arm/boot/dts/Makefile
-@@ -902,11 +902,70 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -902,11 +902,71 @@ dtb-$(CONFIG_ARCH_QCOM) += \
  	qcom-apq8074-dragonboard.dtb \
  	qcom-apq8084-ifc6540.dtb \
  	qcom-apq8084-mtp.dtb \
@@ -76,6 +76,7 @@ Signed-off-by: John Crispin <[email protected]>
 +	qcom-ipq4029-ap-303h.dtb \
 +	qcom-ipq4029-ap-365.dtb \
 +	qcom-ipq4029-gl-b1300.dtb \
++	qcom-ipq4019-gl-b2200.dtb \
 +	qcom-ipq4029-gl-s1300.dtb \
 +	qcom-ipq4029-mr33.dtb \
  	qcom-ipq8064-ap148.dtb \

target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch

@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <[email protected]>
 
 --- a/arch/arm/boot/dts/Makefile
 +++ b/arch/arm/boot/dts/Makefile
-@@ -837,11 +837,68 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -837,11 +837,69 @@ dtb-$(CONFIG_ARCH_QCOM) += \
  	qcom-apq8074-dragonboard.dtb \
  	qcom-apq8084-ifc6540.dtb \
  	qcom-apq8084-mtp.dtb \
@@ -74,6 +74,7 @@ Signed-off-by: John Crispin <[email protected]>
 +	qcom-ipq4029-ap-303h.dtb \
 +	qcom-ipq4029-ap-365.dtb \
 +	qcom-ipq4029-gl-b1300.dtb \
++	qcom-ipq4019-gl-b2200.dtb \
 +	qcom-ipq4029-gl-s1300.dtb \
 +	qcom-ipq4029-mr33.dtb \
  	qcom-ipq8064-ap148.dtb \