|
|
@@ -0,0 +1,226 @@
|
|
|
+/*
|
|
|
+ * Copyright (C) 2005 SAN People
|
|
|
+ * Copyright (C) 2006 Atmel
|
|
|
+ * Copyright (C) 2009-2010 Claudio Mignanti <[email protected]>
|
|
|
+ *
|
|
|
+ * Strongly based on arch/arm/mach-at91/board-sam9260ek.c
|
|
|
+ *
|
|
|
+ * This program is free software; you can redistribute it and/or modify
|
|
|
+ * it under the terms of the GNU General Public License as published by
|
|
|
+ * the Free Software Foundation; either version 2 of the License, or
|
|
|
+ * (at your option) any later version.
|
|
|
+ *
|
|
|
+ * This program is distributed in the hope that it will be useful,
|
|
|
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
|
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
|
+ * GNU General Public License for more details.
|
|
|
+ *
|
|
|
+ * You should have received a copy of the GNU General Public License
|
|
|
+ * along with this program; if not, write to the Free Software
|
|
|
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
|
|
|
+ */
|
|
|
+
|
|
|
+#include <linux/types.h>
|
|
|
+#include <linux/init.h>
|
|
|
+#include <linux/mm.h>
|
|
|
+#include <linux/module.h>
|
|
|
+#include <linux/platform_device.h>
|
|
|
+#include <linux/spi/spi.h>
|
|
|
+#include <linux/gpio.h>
|
|
|
+#include <linux/gpio_keys.h>
|
|
|
+#include <linux/input.h>
|
|
|
+#include <linux/clk.h>
|
|
|
+
|
|
|
+#include <mach/hardware.h>
|
|
|
+#include <asm/setup.h>
|
|
|
+#include <asm/mach-types.h>
|
|
|
+#include <asm/irq.h>
|
|
|
+
|
|
|
+#include <asm/mach/arch.h>
|
|
|
+#include <asm/mach/map.h>
|
|
|
+#include <asm/mach/irq.h>
|
|
|
+
|
|
|
+#include <mach/board.h>
|
|
|
+#include <mach/at91sam9_smc.h>
|
|
|
+
|
|
|
+#include "sam9_smc.h"
|
|
|
+#include "generic.h"
|
|
|
+
|
|
|
+
|
|
|
+static void __init ek_map_io(void)
|
|
|
+{
|
|
|
+ /* Initialize processor: 18.432 MHz crystal */
|
|
|
+ at91sam9260_initialize(18432000);
|
|
|
+
|
|
|
+ /* DGBU on ttyS0. (Rx & Tx only) */
|
|
|
+ at91_register_uart(0, 0, 0);
|
|
|
+
|
|
|
+#if defined(CONFIG_NETUS_SERIALS)
|
|
|
+ /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
|
|
|
+ at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
|
|
|
+ | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
|
|
|
+ | ATMEL_UART_RI);
|
|
|
+
|
|
|
+ /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
|
|
|
+ at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
|
|
|
+
|
|
|
+ /* USART2 on ttyS3. (Rx, Tx) */
|
|
|
+ at91_register_uart(AT91SAM9260_ID_US2, 3, 0);
|
|
|
+#endif
|
|
|
+
|
|
|
+ /* set serial console to ttyS0 (ie, DBGU) */
|
|
|
+ at91_set_serial_console(0);
|
|
|
+}
|
|
|
+
|
|
|
+static void __init ek_init_irq(void)
|
|
|
+{
|
|
|
+ at91sam9260_init_interrupts(NULL);
|
|
|
+}
|
|
|
+
|
|
|
+
|
|
|
+/*
|
|
|
+ * USB Host port
|
|
|
+ */
|
|
|
+static struct at91_usbh_data __initdata ek_usbh_data = {
|
|
|
+ .ports = 2,
|
|
|
+};
|
|
|
+
|
|
|
+/*
|
|
|
+ * USB Device port
|
|
|
+ */
|
|
|
+static struct at91_udc_data __initdata ek_udc_data = {
|
|
|
+ .vbus_pin = AT91_PIN_PC6,
|
|
|
+ .pullup_pin = 0, /* pull-up driven by UDC */
|
|
|
+};
|
|
|
+
|
|
|
+
|
|
|
+/*
|
|
|
+ * SPI devices.
|
|
|
+ */
|
|
|
+static struct spi_board_info ek_spi_devices[] = {
|
|
|
+#if defined(CONFIG_NETUS_USE_DATAFLASH)
|
|
|
+ { /* DataFlash chip */
|
|
|
+ .modalias = "mtd_dataflash",
|
|
|
+ .chip_select = 1,
|
|
|
+ .max_speed_hz = 15 * 1000 * 1000,
|
|
|
+ .bus_num = 0,
|
|
|
+ },
|
|
|
+#endif
|
|
|
+};
|
|
|
+
|
|
|
+
|
|
|
+/*
|
|
|
+ * MACB Ethernet device
|
|
|
+ */
|
|
|
+static struct at91_eth_data __initdata ek_macb_data = {
|
|
|
+ .phy_irq_pin = AT91_PIN_PA29,
|
|
|
+ .is_rmii = 1,
|
|
|
+};
|
|
|
+
|
|
|
+
|
|
|
+/*
|
|
|
+ * MCI (SD/MMC)
|
|
|
+ * det_pin, wp_pin and vcc_pin are not connected
|
|
|
+ */
|
|
|
+static struct at91_mmc_data __initdata ek_mmc_data = {
|
|
|
+ .slot_b = 1,
|
|
|
+ .wire4 = 1,
|
|
|
+};
|
|
|
+
|
|
|
+/*
|
|
|
+ * LEDs
|
|
|
+ */
|
|
|
+static struct gpio_led ek_leds[] = {
|
|
|
+ {
|
|
|
+ .name = "led:red:user",
|
|
|
+ .gpio = AT91_PIN_PC7,
|
|
|
+ .active_low = 0,
|
|
|
+#if defined(CONFIG_NETUS_HEARTBEAT_LED)
|
|
|
+ .default_trigger = "heartbeat",
|
|
|
+#else
|
|
|
+ .default_trigger = "none",
|
|
|
+#endif
|
|
|
+ },
|
|
|
+};
|
|
|
+
|
|
|
+/*
|
|
|
+ * GPIO Buttons
|
|
|
+ */
|
|
|
+#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
|
|
|
+
|
|
|
+static struct gpio_keys_button ek_buttons[] = {
|
|
|
+ {
|
|
|
+ .gpio = AT91_PIN_PC4,
|
|
|
+ .code = BTN_1,
|
|
|
+ .desc = "Button 1",
|
|
|
+ .active_low = 1,
|
|
|
+ .wakeup = 1,
|
|
|
+ },
|
|
|
+};
|
|
|
+
|
|
|
+static struct gpio_keys_platform_data ek_button_data = {
|
|
|
+ .buttons = ek_buttons,
|
|
|
+ .nbuttons = ARRAY_SIZE(ek_buttons),
|
|
|
+};
|
|
|
+
|
|
|
+static struct platform_device ek_button_device = {
|
|
|
+ .name = "gpio-keys",
|
|
|
+ .id = -1,
|
|
|
+ .num_resources = 0,
|
|
|
+ .dev = {
|
|
|
+ .platform_data = &ek_button_data,
|
|
|
+ }
|
|
|
+};
|
|
|
+
|
|
|
+static void __init ek_add_device_buttons(void)
|
|
|
+{
|
|
|
+ at91_set_gpio_input(AT91_PIN_PC4, 1); /* btn1 */
|
|
|
+ at91_set_deglitch(AT91_PIN_PC4, 1);
|
|
|
+
|
|
|
+ platform_device_register(&ek_button_device);
|
|
|
+}
|
|
|
+#else
|
|
|
+static void __init ek_add_device_buttons(void) {}
|
|
|
+#endif
|
|
|
+
|
|
|
+static struct resource gpiodev_resource = {
|
|
|
+ .start = 0xFFFFFFFF,
|
|
|
+};
|
|
|
+
|
|
|
+static void __init ek_board_init(void)
|
|
|
+{
|
|
|
+ /* Serial */
|
|
|
+ at91_add_device_serial();
|
|
|
+ /* USB Host */
|
|
|
+ at91_add_device_usbh(&ek_usbh_data);
|
|
|
+ /* USB Device */
|
|
|
+ at91_add_device_udc(&ek_udc_data);
|
|
|
+ /* SPI */
|
|
|
+ at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
|
|
|
+ /* Ethernet */
|
|
|
+ at91_add_device_eth(&ek_macb_data);
|
|
|
+ /* MMC */
|
|
|
+ at91_add_device_mmc(0, &ek_mmc_data);
|
|
|
+ /* I2C */
|
|
|
+ at91_add_device_i2c(NULL, 0);
|
|
|
+ /* LEDs */
|
|
|
+ at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
|
|
|
+ /* Push Buttons */
|
|
|
+ ek_add_device_buttons();
|
|
|
+ /* Register GPIODEV */
|
|
|
+ platform_device_register_simple("GPIODEV", 0, &gpiodev_resource, 1);
|
|
|
+
|
|
|
+}
|
|
|
+
|
|
|
+MACHINE_START(AT91SAM9G20EK, "Acmesystems Netus FoxBoardG20")
|
|
|
+ /* Maintainer: Claudio Mignanti */
|
|
|
+ .phys_io = AT91_BASE_SYS,
|
|
|
+ .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc,
|
|
|
+ .boot_params = AT91_SDRAM_BASE + 0x100,
|
|
|
+ .timer = &at91sam926x_timer,
|
|
|
+ .map_io = ek_map_io,
|
|
|
+ .init_irq = ek_init_irq,
|
|
|
+ .init_machine = ek_board_init,
|
|
|
+MACHINE_END
|
|
|
+
|
|
|
+
|
Claudio Mignanti