openwrt/target/linux/generic/backport-6.6/713-v6.9-01-net-phy-move-at803x-PHY-driver-to-dedicated-director.patch

From 9e56ff53b4115875667760445b028357848b4748 Mon Sep 17 00:00:00 2001
From: Christian Marangi <[email protected]>
Date: Mon, 29 Jan 2024 15:15:19 +0100
Subject: [PATCH 1/5] net: phy: move at803x PHY driver to dedicated directory

In preparation for addition of other Qcom PHY and to tidy things up,
move the at803x PHY driver to dedicated directory.

The same order in the Kconfig selection is saved.

Signed-off-by: Christian Marangi <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
---
 drivers/net/phy/Kconfig             | 7 +------
 drivers/net/phy/Makefile            | 2 +-
 drivers/net/phy/qcom/Kconfig        | 7 +++++++
 drivers/net/phy/qcom/Makefile       | 2 ++
 drivers/net/phy/{ => qcom}/at803x.c | 0
 5 files changed, 11 insertions(+), 7 deletions(-)
 create mode 100644 drivers/net/phy/qcom/Kconfig
 create mode 100644 drivers/net/phy/qcom/Makefile
 rename drivers/net/phy/{ => qcom}/at803x.c (100%)

--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -318,12 +318,7 @@ config NCN26000_PHY
 	  Currently supports the NCN26000 10BASE-T1S Industrial PHY
 	  with MII interface.
 
-config AT803X_PHY
-	tristate "Qualcomm Atheros AR803X PHYs and QCA833x PHYs"
-	depends on REGULATOR
-	help
-	  Currently supports the AR8030, AR8031, AR8033, AR8035 and internal
-	  QCA8337(Internal qca8k PHY) model
+source "drivers/net/phy/qcom/Kconfig"
 
 config QSEMI_PHY
 	tristate "Quality Semiconductor PHYs"
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -36,7 +36,6 @@ obj-$(CONFIG_ADIN_PHY)		+= adin.o
 obj-$(CONFIG_ADIN1100_PHY)	+= adin1100.o
 obj-$(CONFIG_AMD_PHY)		+= amd.o
 obj-$(CONFIG_AQUANTIA_PHY)	+= aquantia/
-obj-$(CONFIG_AT803X_PHY)	+= at803x.o
 obj-$(CONFIG_AX88796B_PHY)	+= ax88796b.o
 obj-$(CONFIG_BCM54140_PHY)	+= bcm54140.o
 obj-$(CONFIG_BCM63XX_PHY)	+= bcm63xx.o
@@ -82,6 +81,7 @@ obj-$(CONFIG_NCN26000_PHY)	+= ncn26000.o
 obj-$(CONFIG_NXP_C45_TJA11XX_PHY)	+= nxp-c45-tja11xx.o
 obj-$(CONFIG_NXP_CBTX_PHY)	+= nxp-cbtx.o
 obj-$(CONFIG_NXP_TJA11XX_PHY)	+= nxp-tja11xx.o
+obj-y				+= qcom/
 obj-$(CONFIG_QSEMI_PHY)		+= qsemi.o
 obj-$(CONFIG_REALTEK_PHY)	+= realtek.o
 obj-$(CONFIG_RENESAS_PHY)	+= uPD60620.o
--- /dev/null
+++ b/drivers/net/phy/qcom/Kconfig
@@ -0,0 +1,7 @@
+# SPDX-License-Identifier: GPL-2.0-only
+config AT803X_PHY
+	tristate "Qualcomm Atheros AR803X PHYs and QCA833x PHYs"
+	depends on REGULATOR
+	help
+	  Currently supports the AR8030, AR8031, AR8033, AR8035 and internal
+	  QCA8337(Internal qca8k PHY) model
--- /dev/null
+++ b/drivers/net/phy/qcom/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0
+obj-$(CONFIG_AT803X_PHY)	+= at803x.o
--- a/drivers/net/phy/at803x.c
+++ /dev/null
@@ -1,2759 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * drivers/net/phy/at803x.c
- *
- * Driver for Qualcomm Atheros AR803x PHY
- *
- * Author: Matus Ujhelyi <[email protected]>
- */
-
-#include <linux/phy.h>
-#include <linux/module.h>
-#include <linux/string.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/ethtool_netlink.h>
-#include <linux/bitfield.h>
-#include <linux/regulator/of_regulator.h>
-#include <linux/regulator/driver.h>
-#include <linux/regulator/consumer.h>
-#include <linux/of.h>
-#include <linux/phylink.h>
-#include <linux/sfp.h>
-#include <dt-bindings/net/qca-ar803x.h>
-
-#define AT803X_SPECIFIC_FUNCTION_CONTROL	0x10
-#define AT803X_SFC_ASSERT_CRS			BIT(11)
-#define AT803X_SFC_FORCE_LINK			BIT(10)
-#define AT803X_SFC_MDI_CROSSOVER_MODE_M		GENMASK(6, 5)
-#define AT803X_SFC_AUTOMATIC_CROSSOVER		0x3
-#define AT803X_SFC_MANUAL_MDIX			0x1
-#define AT803X_SFC_MANUAL_MDI			0x0
-#define AT803X_SFC_SQE_TEST			BIT(2)
-#define AT803X_SFC_POLARITY_REVERSAL		BIT(1)
-#define AT803X_SFC_DISABLE_JABBER		BIT(0)
-
-#define AT803X_SPECIFIC_STATUS			0x11
-#define AT803X_SS_SPEED_MASK			GENMASK(15, 14)
-#define AT803X_SS_SPEED_1000			2
-#define AT803X_SS_SPEED_100			1
-#define AT803X_SS_SPEED_10			0
-#define AT803X_SS_DUPLEX			BIT(13)
-#define AT803X_SS_SPEED_DUPLEX_RESOLVED		BIT(11)
-#define AT803X_SS_MDIX				BIT(6)
-
-#define QCA808X_SS_SPEED_MASK			GENMASK(9, 7)
-#define QCA808X_SS_SPEED_2500			4
-
-#define AT803X_INTR_ENABLE			0x12
-#define AT803X_INTR_ENABLE_AUTONEG_ERR		BIT(15)
-#define AT803X_INTR_ENABLE_SPEED_CHANGED	BIT(14)
-#define AT803X_INTR_ENABLE_DUPLEX_CHANGED	BIT(13)
-#define AT803X_INTR_ENABLE_PAGE_RECEIVED	BIT(12)
-#define AT803X_INTR_ENABLE_LINK_FAIL		BIT(11)
-#define AT803X_INTR_ENABLE_LINK_SUCCESS		BIT(10)
-#define AT803X_INTR_ENABLE_LINK_FAIL_BX		BIT(8)
-#define AT803X_INTR_ENABLE_LINK_SUCCESS_BX	BIT(7)
-#define AT803X_INTR_ENABLE_WIRESPEED_DOWNGRADE	BIT(5)
-#define AT803X_INTR_ENABLE_POLARITY_CHANGED	BIT(1)
-#define AT803X_INTR_ENABLE_WOL			BIT(0)
-
-#define AT803X_INTR_STATUS			0x13
-
-#define AT803X_SMART_SPEED			0x14
-#define AT803X_SMART_SPEED_ENABLE		BIT(5)
-#define AT803X_SMART_SPEED_RETRY_LIMIT_MASK	GENMASK(4, 2)
-#define AT803X_SMART_SPEED_BYPASS_TIMER		BIT(1)
-#define AT803X_CDT				0x16
-#define AT803X_CDT_MDI_PAIR_MASK		GENMASK(9, 8)
-#define AT803X_CDT_ENABLE_TEST			BIT(0)
-#define AT803X_CDT_STATUS			0x1c
-#define AT803X_CDT_STATUS_STAT_NORMAL		0
-#define AT803X_CDT_STATUS_STAT_SHORT		1
-#define AT803X_CDT_STATUS_STAT_OPEN		2
-#define AT803X_CDT_STATUS_STAT_FAIL		3
-#define AT803X_CDT_STATUS_STAT_MASK		GENMASK(9, 8)
-#define AT803X_CDT_STATUS_DELTA_TIME_MASK	GENMASK(7, 0)
-#define AT803X_LED_CONTROL			0x18
-
-#define AT803X_PHY_MMD3_WOL_CTRL		0x8012
-#define AT803X_WOL_EN				BIT(5)
-#define AT803X_LOC_MAC_ADDR_0_15_OFFSET		0x804C
-#define AT803X_LOC_MAC_ADDR_16_31_OFFSET	0x804B
-#define AT803X_LOC_MAC_ADDR_32_47_OFFSET	0x804A
-#define AT803X_REG_CHIP_CONFIG			0x1f
-#define AT803X_BT_BX_REG_SEL			0x8000
-
-#define AT803X_DEBUG_ADDR			0x1D
-#define AT803X_DEBUG_DATA			0x1E
-
-#define AT803X_MODE_CFG_MASK			0x0F
-#define AT803X_MODE_CFG_BASET_RGMII		0x00
-#define AT803X_MODE_CFG_BASET_SGMII		0x01
-#define AT803X_MODE_CFG_BX1000_RGMII_50OHM	0x02
-#define AT803X_MODE_CFG_BX1000_RGMII_75OHM	0x03
-#define AT803X_MODE_CFG_BX1000_CONV_50OHM	0x04
-#define AT803X_MODE_CFG_BX1000_CONV_75OHM	0x05
-#define AT803X_MODE_CFG_FX100_RGMII_50OHM	0x06
-#define AT803X_MODE_CFG_FX100_CONV_50OHM	0x07
-#define AT803X_MODE_CFG_RGMII_AUTO_MDET		0x0B
-#define AT803X_MODE_CFG_FX100_RGMII_75OHM	0x0E
-#define AT803X_MODE_CFG_FX100_CONV_75OHM	0x0F
-
-#define AT803X_PSSR				0x11	/*PHY-Specific Status Register*/
-#define AT803X_PSSR_MR_AN_COMPLETE		0x0200
-
-#define AT803X_DEBUG_ANALOG_TEST_CTRL		0x00
-#define QCA8327_DEBUG_MANU_CTRL_EN		BIT(2)
-#define QCA8337_DEBUG_MANU_CTRL_EN		GENMASK(3, 2)
-#define AT803X_DEBUG_RX_CLK_DLY_EN		BIT(15)
-
-#define AT803X_DEBUG_SYSTEM_CTRL_MODE		0x05
-#define AT803X_DEBUG_TX_CLK_DLY_EN		BIT(8)
-
-#define AT803X_DEBUG_REG_HIB_CTRL		0x0b
-#define   AT803X_DEBUG_HIB_CTRL_SEL_RST_80U	BIT(10)
-#define   AT803X_DEBUG_HIB_CTRL_EN_ANY_CHANGE	BIT(13)
-#define   AT803X_DEBUG_HIB_CTRL_PS_HIB_EN	BIT(15)
-
-#define AT803X_DEBUG_REG_3C			0x3C
-
-#define AT803X_DEBUG_REG_GREEN			0x3D
-#define   AT803X_DEBUG_GATE_CLK_IN1000		BIT(6)
-
-#define AT803X_DEBUG_REG_1F			0x1F
-#define AT803X_DEBUG_PLL_ON			BIT(2)
-#define AT803X_DEBUG_RGMII_1V8			BIT(3)
-
-#define MDIO_AZ_DEBUG				0x800D
-
-/* AT803x supports either the XTAL input pad, an internal PLL or the
- * DSP as clock reference for the clock output pad. The XTAL reference
- * is only used for 25 MHz output, all other frequencies need the PLL.
- * The DSP as a clock reference is used in synchronous ethernet
- * applications.
- *
- * By default the PLL is only enabled if there is a link. Otherwise
- * the PHY will go into low power state and disabled the PLL. You can
- * set the PLL_ON bit (see debug register 0x1f) to keep the PLL always
- * enabled.
- */
-#define AT803X_MMD7_CLK25M			0x8016
-#define AT803X_CLK_OUT_MASK			GENMASK(4, 2)
-#define AT803X_CLK_OUT_25MHZ_XTAL		0
-#define AT803X_CLK_OUT_25MHZ_DSP		1
-#define AT803X_CLK_OUT_50MHZ_PLL		2
-#define AT803X_CLK_OUT_50MHZ_DSP		3
-#define AT803X_CLK_OUT_62_5MHZ_PLL		4
-#define AT803X_CLK_OUT_62_5MHZ_DSP		5
-#define AT803X_CLK_OUT_125MHZ_PLL		6
-#define AT803X_CLK_OUT_125MHZ_DSP		7
-
-/* The AR8035 has another mask which is compatible with the AR8031/AR8033 mask
- * but doesn't support choosing between XTAL/PLL and DSP.
- */
-#define AT8035_CLK_OUT_MASK			GENMASK(4, 3)
-
-#define AT803X_CLK_OUT_STRENGTH_MASK		GENMASK(8, 7)
-#define AT803X_CLK_OUT_STRENGTH_FULL		0
-#define AT803X_CLK_OUT_STRENGTH_HALF		1
-#define AT803X_CLK_OUT_STRENGTH_QUARTER		2
-
-#define AT803X_DEFAULT_DOWNSHIFT		5
-#define AT803X_MIN_DOWNSHIFT			2
-#define AT803X_MAX_DOWNSHIFT			9
-
-#define AT803X_MMD3_SMARTEEE_CTL1		0x805b
-#define AT803X_MMD3_SMARTEEE_CTL2		0x805c
-#define AT803X_MMD3_SMARTEEE_CTL3		0x805d
-#define AT803X_MMD3_SMARTEEE_CTL3_LPI_EN	BIT(8)
-
-#define ATH9331_PHY_ID				0x004dd041
-#define ATH8030_PHY_ID				0x004dd076
-#define ATH8031_PHY_ID				0x004dd074
-#define ATH8032_PHY_ID				0x004dd023
-#define ATH8035_PHY_ID				0x004dd072
-#define AT8030_PHY_ID_MASK			0xffffffef
-
-#define QCA8081_PHY_ID				0x004dd101
-
-#define QCA8327_A_PHY_ID			0x004dd033
-#define QCA8327_B_PHY_ID			0x004dd034
-#define QCA8337_PHY_ID				0x004dd036
-#define QCA9561_PHY_ID				0x004dd042
-#define QCA8K_PHY_ID_MASK			0xffffffff
-
-#define QCA8K_DEVFLAGS_REVISION_MASK		GENMASK(2, 0)
-
-#define AT803X_PAGE_FIBER			0
-#define AT803X_PAGE_COPPER			1
-
-/* don't turn off internal PLL */
-#define AT803X_KEEP_PLL_ENABLED			BIT(0)
-#define AT803X_DISABLE_SMARTEEE			BIT(1)
-
-/* disable hibernation mode */
-#define AT803X_DISABLE_HIBERNATION_MODE		BIT(2)
-
-/* ADC threshold */
-#define QCA808X_PHY_DEBUG_ADC_THRESHOLD		0x2c80
-#define QCA808X_ADC_THRESHOLD_MASK		GENMASK(7, 0)
-#define QCA808X_ADC_THRESHOLD_80MV		0
-#define QCA808X_ADC_THRESHOLD_100MV		0xf0
-#define QCA808X_ADC_THRESHOLD_200MV		0x0f
-#define QCA808X_ADC_THRESHOLD_300MV		0xff
-
-/* CLD control */
-#define QCA808X_PHY_MMD3_ADDR_CLD_CTRL7		0x8007
-#define QCA808X_8023AZ_AFE_CTRL_MASK		GENMASK(8, 4)
-#define QCA808X_8023AZ_AFE_EN			0x90
-
-/* AZ control */
-#define QCA808X_PHY_MMD3_AZ_TRAINING_CTRL	0x8008
-#define QCA808X_MMD3_AZ_TRAINING_VAL		0x1c32
-
-#define QCA808X_PHY_MMD1_MSE_THRESHOLD_20DB	0x8014
-#define QCA808X_MSE_THRESHOLD_20DB_VALUE	0x529
-
-#define QCA808X_PHY_MMD1_MSE_THRESHOLD_17DB	0x800E
-#define QCA808X_MSE_THRESHOLD_17DB_VALUE	0x341
-
-#define QCA808X_PHY_MMD1_MSE_THRESHOLD_27DB	0x801E
-#define QCA808X_MSE_THRESHOLD_27DB_VALUE	0x419
-
-#define QCA808X_PHY_MMD1_MSE_THRESHOLD_28DB	0x8020
-#define QCA808X_MSE_THRESHOLD_28DB_VALUE	0x341
-
-#define QCA808X_PHY_MMD7_TOP_OPTION1		0x901c
-#define QCA808X_TOP_OPTION1_DATA		0x0
-
-#define QCA808X_PHY_MMD3_DEBUG_1		0xa100
-#define QCA808X_MMD3_DEBUG_1_VALUE		0x9203
-#define QCA808X_PHY_MMD3_DEBUG_2		0xa101
-#define QCA808X_MMD3_DEBUG_2_VALUE		0x48ad
-#define QCA808X_PHY_MMD3_DEBUG_3		0xa103
-#define QCA808X_MMD3_DEBUG_3_VALUE		0x1698
-#define QCA808X_PHY_MMD3_DEBUG_4		0xa105
-#define QCA808X_MMD3_DEBUG_4_VALUE		0x8001
-#define QCA808X_PHY_MMD3_DEBUG_5		0xa106
-#define QCA808X_MMD3_DEBUG_5_VALUE		0x1111
-#define QCA808X_PHY_MMD3_DEBUG_6		0xa011
-#define QCA808X_MMD3_DEBUG_6_VALUE		0x5f85
-
-/* master/slave seed config */
-#define QCA808X_PHY_DEBUG_LOCAL_SEED		9
-#define QCA808X_MASTER_SLAVE_SEED_ENABLE	BIT(1)
-#define QCA808X_MASTER_SLAVE_SEED_CFG		GENMASK(12, 2)
-#define QCA808X_MASTER_SLAVE_SEED_RANGE		0x32
-
-/* Hibernation yields lower power consumpiton in contrast with normal operation mode.
- * when the copper cable is unplugged, the PHY enters into hibernation mode in about 10s.
- */
-#define QCA808X_DBG_AN_TEST			0xb
-#define QCA808X_HIBERNATION_EN			BIT(15)
-
-#define QCA808X_CDT_ENABLE_TEST			BIT(15)
-#define QCA808X_CDT_INTER_CHECK_DIS		BIT(13)
-#define QCA808X_CDT_STATUS			BIT(11)
-#define QCA808X_CDT_LENGTH_UNIT			BIT(10)
-
-#define QCA808X_MMD3_CDT_STATUS			0x8064
-#define QCA808X_MMD3_CDT_DIAG_PAIR_A		0x8065
-#define QCA808X_MMD3_CDT_DIAG_PAIR_B		0x8066
-#define QCA808X_MMD3_CDT_DIAG_PAIR_C		0x8067
-#define QCA808X_MMD3_CDT_DIAG_PAIR_D		0x8068
-#define QCA808X_CDT_DIAG_LENGTH_SAME_SHORT	GENMASK(15, 8)
-#define QCA808X_CDT_DIAG_LENGTH_CROSS_SHORT	GENMASK(7, 0)
-
-#define QCA808X_CDT_CODE_PAIR_A			GENMASK(15, 12)
-#define QCA808X_CDT_CODE_PAIR_B			GENMASK(11, 8)
-#define QCA808X_CDT_CODE_PAIR_C			GENMASK(7, 4)
-#define QCA808X_CDT_CODE_PAIR_D			GENMASK(3, 0)
-
-#define QCA808X_CDT_STATUS_STAT_TYPE		GENMASK(1, 0)
-#define QCA808X_CDT_STATUS_STAT_FAIL		FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_TYPE, 0)
-#define QCA808X_CDT_STATUS_STAT_NORMAL		FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_TYPE, 1)
-#define QCA808X_CDT_STATUS_STAT_SAME_OPEN	FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_TYPE, 2)
-#define QCA808X_CDT_STATUS_STAT_SAME_SHORT	FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_TYPE, 3)
-
-#define QCA808X_CDT_STATUS_STAT_MDI		GENMASK(3, 2)
-#define QCA808X_CDT_STATUS_STAT_MDI1		FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_MDI, 1)
-#define QCA808X_CDT_STATUS_STAT_MDI2		FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_MDI, 2)
-#define QCA808X_CDT_STATUS_STAT_MDI3		FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_MDI, 3)
-
-/* NORMAL are MDI with type set to 0 */
-#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_NORMAL	QCA808X_CDT_STATUS_STAT_MDI1
-#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_OPEN		(QCA808X_CDT_STATUS_STAT_SAME_OPEN |\
-									 QCA808X_CDT_STATUS_STAT_MDI1)
-#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_SHORT	(QCA808X_CDT_STATUS_STAT_SAME_SHORT |\
-									 QCA808X_CDT_STATUS_STAT_MDI1)
-#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_NORMAL	QCA808X_CDT_STATUS_STAT_MDI2
-#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_OPEN		(QCA808X_CDT_STATUS_STAT_SAME_OPEN |\
-									 QCA808X_CDT_STATUS_STAT_MDI2)
-#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_SHORT	(QCA808X_CDT_STATUS_STAT_SAME_SHORT |\
-									 QCA808X_CDT_STATUS_STAT_MDI2)
-#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_NORMAL	QCA808X_CDT_STATUS_STAT_MDI3
-#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_OPEN		(QCA808X_CDT_STATUS_STAT_SAME_OPEN |\
-									 QCA808X_CDT_STATUS_STAT_MDI3)
-#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_SHORT	(QCA808X_CDT_STATUS_STAT_SAME_SHORT |\
-									 QCA808X_CDT_STATUS_STAT_MDI3)
-
-/* Added for reference of existence but should be handled by wait_for_completion already */
-#define QCA808X_CDT_STATUS_STAT_BUSY		(BIT(1) | BIT(3))
-
-#define QCA808X_MMD7_LED_GLOBAL			0x8073
-#define QCA808X_LED_BLINK_1			GENMASK(11, 6)
-#define QCA808X_LED_BLINK_2			GENMASK(5, 0)
-/* Values are the same for both BLINK_1 and BLINK_2 */
-#define QCA808X_LED_BLINK_FREQ_MASK		GENMASK(5, 3)
-#define QCA808X_LED_BLINK_FREQ_2HZ		FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x0)
-#define QCA808X_LED_BLINK_FREQ_4HZ		FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x1)
-#define QCA808X_LED_BLINK_FREQ_8HZ		FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x2)
-#define QCA808X_LED_BLINK_FREQ_16HZ		FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x3)
-#define QCA808X_LED_BLINK_FREQ_32HZ		FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x4)
-#define QCA808X_LED_BLINK_FREQ_64HZ		FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x5)
-#define QCA808X_LED_BLINK_FREQ_128HZ		FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x6)
-#define QCA808X_LED_BLINK_FREQ_256HZ		FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x7)
-#define QCA808X_LED_BLINK_DUTY_MASK		GENMASK(2, 0)
-#define QCA808X_LED_BLINK_DUTY_50_50		FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x0)
-#define QCA808X_LED_BLINK_DUTY_75_25		FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x1)
-#define QCA808X_LED_BLINK_DUTY_25_75		FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x2)
-#define QCA808X_LED_BLINK_DUTY_33_67		FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x3)
-#define QCA808X_LED_BLINK_DUTY_67_33		FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x4)
-#define QCA808X_LED_BLINK_DUTY_17_83		FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x5)
-#define QCA808X_LED_BLINK_DUTY_83_17		FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x6)
-#define QCA808X_LED_BLINK_DUTY_8_92		FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x7)
-
-#define QCA808X_MMD7_LED2_CTRL			0x8074
-#define QCA808X_MMD7_LED2_FORCE_CTRL		0x8075
-#define QCA808X_MMD7_LED1_CTRL			0x8076
-#define QCA808X_MMD7_LED1_FORCE_CTRL		0x8077
-#define QCA808X_MMD7_LED0_CTRL			0x8078
-#define QCA808X_MMD7_LED_CTRL(x)		(0x8078 - ((x) * 2))
-
-/* LED hw control pattern is the same for every LED */
-#define QCA808X_LED_PATTERN_MASK		GENMASK(15, 0)
-#define QCA808X_LED_SPEED2500_ON		BIT(15)
-#define QCA808X_LED_SPEED2500_BLINK		BIT(14)
-/* Follow blink trigger even if duplex or speed condition doesn't match */
-#define QCA808X_LED_BLINK_CHECK_BYPASS		BIT(13)
-#define QCA808X_LED_FULL_DUPLEX_ON		BIT(12)
-#define QCA808X_LED_HALF_DUPLEX_ON		BIT(11)
-#define QCA808X_LED_TX_BLINK			BIT(10)
-#define QCA808X_LED_RX_BLINK			BIT(9)
-#define QCA808X_LED_TX_ON_10MS			BIT(8)
-#define QCA808X_LED_RX_ON_10MS			BIT(7)
-#define QCA808X_LED_SPEED1000_ON		BIT(6)
-#define QCA808X_LED_SPEED100_ON			BIT(5)
-#define QCA808X_LED_SPEED10_ON			BIT(4)
-#define QCA808X_LED_COLLISION_BLINK		BIT(3)
-#define QCA808X_LED_SPEED1000_BLINK		BIT(2)
-#define QCA808X_LED_SPEED100_BLINK		BIT(1)
-#define QCA808X_LED_SPEED10_BLINK		BIT(0)
-
-#define QCA808X_MMD7_LED0_FORCE_CTRL		0x8079
-#define QCA808X_MMD7_LED_FORCE_CTRL(x)		(0x8079 - ((x) * 2))
-
-/* LED force ctrl is the same for every LED
- * No documentation exist for this, not even internal one
- * with NDA as QCOM gives only info about configuring
- * hw control pattern rules and doesn't indicate any way
- * to force the LED to specific mode.
- * These define comes from reverse and testing and maybe
- * lack of some info or some info are not entirely correct.
- * For the basic LED control and hw control these finding
- * are enough to support LED control in all the required APIs.
- *
- * On doing some comparison with implementation with qca807x,
- * it was found that it's 1:1 equal to it and confirms all the
- * reverse done. It was also found further specification with the
- * force mode and the blink modes.
- */
-#define QCA808X_LED_FORCE_EN			BIT(15)
-#define QCA808X_LED_FORCE_MODE_MASK		GENMASK(14, 13)
-#define QCA808X_LED_FORCE_BLINK_1		FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x3)
-#define QCA808X_LED_FORCE_BLINK_2		FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x2)
-#define QCA808X_LED_FORCE_ON			FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x1)
-#define QCA808X_LED_FORCE_OFF			FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x0)
-
-#define QCA808X_MMD7_LED_POLARITY_CTRL		0x901a
-/* QSDK sets by default 0x46 to this reg that sets BIT 6 for
- * LED to active high. It's not clear what BIT 3 and BIT 4 does.
- */
-#define QCA808X_LED_ACTIVE_HIGH			BIT(6)
-
-/* QCA808X 1G chip type */
-#define QCA808X_PHY_MMD7_CHIP_TYPE		0x901d
-#define QCA808X_PHY_CHIP_TYPE_1G		BIT(0)
-
-#define QCA8081_PHY_SERDES_MMD1_FIFO_CTRL	0x9072
-#define QCA8081_PHY_FIFO_RSTN			BIT(11)
-
-MODULE_DESCRIPTION("Qualcomm Atheros AR803x and QCA808X PHY driver");
-MODULE_AUTHOR("Matus Ujhelyi");
-MODULE_LICENSE("GPL");
-
-enum stat_access_type {
-	PHY,
-	MMD
-};
-
-struct at803x_hw_stat {
-	const char *string;
-	u8 reg;
-	u32 mask;
-	enum stat_access_type access_type;
-};
-
-static struct at803x_hw_stat qca83xx_hw_stats[] = {
-	{ "phy_idle_errors", 0xa, GENMASK(7, 0), PHY},
-	{ "phy_receive_errors", 0x15, GENMASK(15, 0), PHY},
-	{ "eee_wake_errors", 0x16, GENMASK(15, 0), MMD},
-};
-
-struct at803x_ss_mask {
-	u16 speed_mask;
-	u8 speed_shift;
-};
-
-struct at803x_priv {
-	int flags;
-	u16 clk_25m_reg;
-	u16 clk_25m_mask;
-	u8 smarteee_lpi_tw_1g;
-	u8 smarteee_lpi_tw_100m;
-	bool is_fiber;
-	bool is_1000basex;
-	struct regulator_dev *vddio_rdev;
-	struct regulator_dev *vddh_rdev;
-	u64 stats[ARRAY_SIZE(qca83xx_hw_stats)];
-	int led_polarity_mode;
-};
-
-struct at803x_context {
-	u16 bmcr;
-	u16 advertise;
-	u16 control1000;
-	u16 int_enable;
-	u16 smart_speed;
-	u16 led_control;
-};
-
-static int at803x_debug_reg_write(struct phy_device *phydev, u16 reg, u16 data)
-{
-	int ret;
-
-	ret = phy_write(phydev, AT803X_DEBUG_ADDR, reg);
-	if (ret < 0)
-		return ret;
-
-	return phy_write(phydev, AT803X_DEBUG_DATA, data);
-}
-
-static int at803x_debug_reg_read(struct phy_device *phydev, u16 reg)
-{
-	int ret;
-
-	ret = phy_write(phydev, AT803X_DEBUG_ADDR, reg);
-	if (ret < 0)
-		return ret;
-
-	return phy_read(phydev, AT803X_DEBUG_DATA);
-}
-
-static int at803x_debug_reg_mask(struct phy_device *phydev, u16 reg,
-				 u16 clear, u16 set)
-{
-	u16 val;
-	int ret;
-
-	ret = at803x_debug_reg_read(phydev, reg);
-	if (ret < 0)
-		return ret;
-
-	val = ret & 0xffff;
-	val &= ~clear;
-	val |= set;
-
-	return phy_write(phydev, AT803X_DEBUG_DATA, val);
-}
-
-static int at803x_write_page(struct phy_device *phydev, int page)
-{
-	int mask;
-	int set;
-
-	if (page == AT803X_PAGE_COPPER) {
-		set = AT803X_BT_BX_REG_SEL;
-		mask = 0;
-	} else {
-		set = 0;
-		mask = AT803X_BT_BX_REG_SEL;
-	}
-
-	return __phy_modify(phydev, AT803X_REG_CHIP_CONFIG, mask, set);
-}
-
-static int at803x_read_page(struct phy_device *phydev)
-{
-	int ccr = __phy_read(phydev, AT803X_REG_CHIP_CONFIG);
-
-	if (ccr < 0)
-		return ccr;
-
-	if (ccr & AT803X_BT_BX_REG_SEL)
-		return AT803X_PAGE_COPPER;
-
-	return AT803X_PAGE_FIBER;
-}
-
-static int at803x_enable_rx_delay(struct phy_device *phydev)
-{
-	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL, 0,
-				     AT803X_DEBUG_RX_CLK_DLY_EN);
-}
-
-static int at803x_enable_tx_delay(struct phy_device *phydev)
-{
-	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_SYSTEM_CTRL_MODE, 0,
-				     AT803X_DEBUG_TX_CLK_DLY_EN);
-}
-
-static int at803x_disable_rx_delay(struct phy_device *phydev)
-{
-	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL,
-				     AT803X_DEBUG_RX_CLK_DLY_EN, 0);
-}
-
-static int at803x_disable_tx_delay(struct phy_device *phydev)
-{
-	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_SYSTEM_CTRL_MODE,
-				     AT803X_DEBUG_TX_CLK_DLY_EN, 0);
-}
-
-/* save relevant PHY registers to private copy */
-static void at803x_context_save(struct phy_device *phydev,
-				struct at803x_context *context)
-{
-	context->bmcr = phy_read(phydev, MII_BMCR);
-	context->advertise = phy_read(phydev, MII_ADVERTISE);
-	context->control1000 = phy_read(phydev, MII_CTRL1000);
-	context->int_enable = phy_read(phydev, AT803X_INTR_ENABLE);
-	context->smart_speed = phy_read(phydev, AT803X_SMART_SPEED);
-	context->led_control = phy_read(phydev, AT803X_LED_CONTROL);
-}
-
-/* restore relevant PHY registers from private copy */
-static void at803x_context_restore(struct phy_device *phydev,
-				   const struct at803x_context *context)
-{
-	phy_write(phydev, MII_BMCR, context->bmcr);
-	phy_write(phydev, MII_ADVERTISE, context->advertise);
-	phy_write(phydev, MII_CTRL1000, context->control1000);
-	phy_write(phydev, AT803X_INTR_ENABLE, context->int_enable);
-	phy_write(phydev, AT803X_SMART_SPEED, context->smart_speed);
-	phy_write(phydev, AT803X_LED_CONTROL, context->led_control);
-}
-
-static int at803x_set_wol(struct phy_device *phydev,
-			  struct ethtool_wolinfo *wol)
-{
-	int ret, irq_enabled;
-
-	if (wol->wolopts & WAKE_MAGIC) {
-		struct net_device *ndev = phydev->attached_dev;
-		const u8 *mac;
-		unsigned int i;
-		static const unsigned int offsets[] = {
-			AT803X_LOC_MAC_ADDR_32_47_OFFSET,
-			AT803X_LOC_MAC_ADDR_16_31_OFFSET,
-			AT803X_LOC_MAC_ADDR_0_15_OFFSET,
-		};
-
-		if (!ndev)
-			return -ENODEV;
-
-		mac = (const u8 *)ndev->dev_addr;
-
-		if (!is_valid_ether_addr(mac))
-			return -EINVAL;
-
-		for (i = 0; i < 3; i++)
-			phy_write_mmd(phydev, MDIO_MMD_PCS, offsets[i],
-				      mac[(i * 2) + 1] | (mac[(i * 2)] << 8));
-
-		/* Enable WOL interrupt */
-		ret = phy_modify(phydev, AT803X_INTR_ENABLE, 0, AT803X_INTR_ENABLE_WOL);
-		if (ret)
-			return ret;
-	} else {
-		/* Disable WOL interrupt */
-		ret = phy_modify(phydev, AT803X_INTR_ENABLE, AT803X_INTR_ENABLE_WOL, 0);
-		if (ret)
-			return ret;
-	}
-
-	/* Clear WOL status */
-	ret = phy_read(phydev, AT803X_INTR_STATUS);
-	if (ret < 0)
-		return ret;
-
-	/* Check if there are other interrupts except for WOL triggered when PHY is
-	 * in interrupt mode, only the interrupts enabled by AT803X_INTR_ENABLE can
-	 * be passed up to the interrupt PIN.
-	 */
-	irq_enabled = phy_read(phydev, AT803X_INTR_ENABLE);
-	if (irq_enabled < 0)
-		return irq_enabled;
-
-	irq_enabled &= ~AT803X_INTR_ENABLE_WOL;
-	if (ret & irq_enabled && !phy_polling_mode(phydev))
-		phy_trigger_machine(phydev);
-
-	return 0;
-}
-
-static void at803x_get_wol(struct phy_device *phydev,
-			   struct ethtool_wolinfo *wol)
-{
-	int value;
-
-	wol->supported = WAKE_MAGIC;
-	wol->wolopts = 0;
-
-	value = phy_read(phydev, AT803X_INTR_ENABLE);
-	if (value < 0)
-		return;
-
-	if (value & AT803X_INTR_ENABLE_WOL)
-		wol->wolopts |= WAKE_MAGIC;
-}
-
-static int qca83xx_get_sset_count(struct phy_device *phydev)
-{
-	return ARRAY_SIZE(qca83xx_hw_stats);
-}
-
-static void qca83xx_get_strings(struct phy_device *phydev, u8 *data)
-{
-	int i;
-
-	for (i = 0; i < ARRAY_SIZE(qca83xx_hw_stats); i++) {
-		strscpy(data + i * ETH_GSTRING_LEN,
-			qca83xx_hw_stats[i].string, ETH_GSTRING_LEN);
-	}
-}
-
-static u64 qca83xx_get_stat(struct phy_device *phydev, int i)
-{
-	struct at803x_hw_stat stat = qca83xx_hw_stats[i];
-	struct at803x_priv *priv = phydev->priv;
-	int val;
-	u64 ret;
-
-	if (stat.access_type == MMD)
-		val = phy_read_mmd(phydev, MDIO_MMD_PCS, stat.reg);
-	else
-		val = phy_read(phydev, stat.reg);
-
-	if (val < 0) {
-		ret = U64_MAX;
-	} else {
-		val = val & stat.mask;
-		priv->stats[i] += val;
-		ret = priv->stats[i];
-	}
-
-	return ret;
-}
-
-static void qca83xx_get_stats(struct phy_device *phydev,
-			      struct ethtool_stats *stats, u64 *data)
-{
-	int i;
-
-	for (i = 0; i < ARRAY_SIZE(qca83xx_hw_stats); i++)
-		data[i] = qca83xx_get_stat(phydev, i);
-}
-
-static int at803x_suspend(struct phy_device *phydev)
-{
-	int value;
-	int wol_enabled;
-
-	value = phy_read(phydev, AT803X_INTR_ENABLE);
-	wol_enabled = value & AT803X_INTR_ENABLE_WOL;
-
-	if (wol_enabled)
-		value = BMCR_ISOLATE;
-	else
-		value = BMCR_PDOWN;
-
-	phy_modify(phydev, MII_BMCR, 0, value);
-
-	return 0;
-}
-
-static int at803x_resume(struct phy_device *phydev)
-{
-	return phy_modify(phydev, MII_BMCR, BMCR_PDOWN | BMCR_ISOLATE, 0);
-}
-
-static int at803x_parse_dt(struct phy_device *phydev)
-{
-	struct device_node *node = phydev->mdio.dev.of_node;
-	struct at803x_priv *priv = phydev->priv;
-	u32 freq, strength, tw;
-	unsigned int sel;
-	int ret;
-
-	if (!IS_ENABLED(CONFIG_OF_MDIO))
-		return 0;
-
-	if (of_property_read_bool(node, "qca,disable-smarteee"))
-		priv->flags |= AT803X_DISABLE_SMARTEEE;
-
-	if (of_property_read_bool(node, "qca,disable-hibernation-mode"))
-		priv->flags |= AT803X_DISABLE_HIBERNATION_MODE;
-
-	if (!of_property_read_u32(node, "qca,smarteee-tw-us-1g", &tw)) {
-		if (!tw || tw > 255) {
-			phydev_err(phydev, "invalid qca,smarteee-tw-us-1g\n");
-			return -EINVAL;
-		}
-		priv->smarteee_lpi_tw_1g = tw;
-	}
-
-	if (!of_property_read_u32(node, "qca,smarteee-tw-us-100m", &tw)) {
-		if (!tw || tw > 255) {
-			phydev_err(phydev, "invalid qca,smarteee-tw-us-100m\n");
-			return -EINVAL;
-		}
-		priv->smarteee_lpi_tw_100m = tw;
-	}
-
-	ret = of_property_read_u32(node, "qca,clk-out-frequency", &freq);
-	if (!ret) {
-		switch (freq) {
-		case 25000000:
-			sel = AT803X_CLK_OUT_25MHZ_XTAL;
-			break;
-		case 50000000:
-			sel = AT803X_CLK_OUT_50MHZ_PLL;
-			break;
-		case 62500000:
-			sel = AT803X_CLK_OUT_62_5MHZ_PLL;
-			break;
-		case 125000000:
-			sel = AT803X_CLK_OUT_125MHZ_PLL;
-			break;
-		default:
-			phydev_err(phydev, "invalid qca,clk-out-frequency\n");
-			return -EINVAL;
-		}
-
-		priv->clk_25m_reg |= FIELD_PREP(AT803X_CLK_OUT_MASK, sel);
-		priv->clk_25m_mask |= AT803X_CLK_OUT_MASK;
-	}
-
-	ret = of_property_read_u32(node, "qca,clk-out-strength", &strength);
-	if (!ret) {
-		priv->clk_25m_mask |= AT803X_CLK_OUT_STRENGTH_MASK;
-		switch (strength) {
-		case AR803X_STRENGTH_FULL:
-			priv->clk_25m_reg |= AT803X_CLK_OUT_STRENGTH_FULL;
-			break;
-		case AR803X_STRENGTH_HALF:
-			priv->clk_25m_reg |= AT803X_CLK_OUT_STRENGTH_HALF;
-			break;
-		case AR803X_STRENGTH_QUARTER:
-			priv->clk_25m_reg |= AT803X_CLK_OUT_STRENGTH_QUARTER;
-			break;
-		default:
-			phydev_err(phydev, "invalid qca,clk-out-strength\n");
-			return -EINVAL;
-		}
-	}
-
-	return 0;
-}
-
-static int at803x_probe(struct phy_device *phydev)
-{
-	struct device *dev = &phydev->mdio.dev;
-	struct at803x_priv *priv;
-	int ret;
-
-	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
-	if (!priv)
-		return -ENOMEM;
-
-	/* Init LED polarity mode to -1 */
-	priv->led_polarity_mode = -1;
-
-	phydev->priv = priv;
-
-	ret = at803x_parse_dt(phydev);
-	if (ret)
-		return ret;
-
-	return 0;
-}
-
-static int at803x_get_features(struct phy_device *phydev)
-{
-	struct at803x_priv *priv = phydev->priv;
-	int err;
-
-	err = genphy_read_abilities(phydev);
-	if (err)
-		return err;
-
-	if (phydev->drv->phy_id != ATH8031_PHY_ID)
-		return 0;
-
-	/* AR8031/AR8033 have different status registers
-	 * for copper and fiber operation. However, the
-	 * extended status register is the same for both
-	 * operation modes.
-	 *
-	 * As a result of that, ESTATUS_1000_XFULL is set
-	 * to 1 even when operating in copper TP mode.
-	 *
-	 * Remove this mode from the supported link modes
-	 * when not operating in 1000BaseX mode.
-	 */
-	if (!priv->is_1000basex)
-		linkmode_clear_bit(ETHTOOL_LINK_MODE_1000baseX_Full_BIT,
-				   phydev->supported);
-
-	return 0;
-}
-
-static int at803x_smarteee_config(struct phy_device *phydev)
-{
-	struct at803x_priv *priv = phydev->priv;
-	u16 mask = 0, val = 0;
-	int ret;
-
-	if (priv->flags & AT803X_DISABLE_SMARTEEE)
-		return phy_modify_mmd(phydev, MDIO_MMD_PCS,
-				      AT803X_MMD3_SMARTEEE_CTL3,
-				      AT803X_MMD3_SMARTEEE_CTL3_LPI_EN, 0);
-
-	if (priv->smarteee_lpi_tw_1g) {
-		mask |= 0xff00;
-		val |= priv->smarteee_lpi_tw_1g << 8;
-	}
-	if (priv->smarteee_lpi_tw_100m) {
-		mask |= 0x00ff;
-		val |= priv->smarteee_lpi_tw_100m;
-	}
-	if (!mask)
-		return 0;
-
-	ret = phy_modify_mmd(phydev, MDIO_MMD_PCS, AT803X_MMD3_SMARTEEE_CTL1,
-			     mask, val);
-	if (ret)
-		return ret;
-
-	return phy_modify_mmd(phydev, MDIO_MMD_PCS, AT803X_MMD3_SMARTEEE_CTL3,
-			      AT803X_MMD3_SMARTEEE_CTL3_LPI_EN,
-			      AT803X_MMD3_SMARTEEE_CTL3_LPI_EN);
-}
-
-static int at803x_clk_out_config(struct phy_device *phydev)
-{
-	struct at803x_priv *priv = phydev->priv;
-
-	if (!priv->clk_25m_mask)
-		return 0;
-
-	return phy_modify_mmd(phydev, MDIO_MMD_AN, AT803X_MMD7_CLK25M,
-			      priv->clk_25m_mask, priv->clk_25m_reg);
-}
-
-static int at8031_pll_config(struct phy_device *phydev)
-{
-	struct at803x_priv *priv = phydev->priv;
-
-	/* The default after hardware reset is PLL OFF. After a soft reset, the
-	 * values are retained.
-	 */
-	if (priv->flags & AT803X_KEEP_PLL_ENABLED)
-		return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F,
-					     0, AT803X_DEBUG_PLL_ON);
-	else
-		return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F,
-					     AT803X_DEBUG_PLL_ON, 0);
-}
-
-static int at803x_hibernation_mode_config(struct phy_device *phydev)
-{
-	struct at803x_priv *priv = phydev->priv;
-
-	/* The default after hardware reset is hibernation mode enabled. After
-	 * software reset, the value is retained.
-	 */
-	if (!(priv->flags & AT803X_DISABLE_HIBERNATION_MODE))
-		return 0;
-
-	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_HIB_CTRL,
-					 AT803X_DEBUG_HIB_CTRL_PS_HIB_EN, 0);
-}
-
-static int at803x_config_init(struct phy_device *phydev)
-{
-	int ret;
-
-	/* The RX and TX delay default is:
-	 *   after HW reset: RX delay enabled and TX delay disabled
-	 *   after SW reset: RX delay enabled, while TX delay retains the
-	 *   value before reset.
-	 */
-	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
-	    phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID)
-		ret = at803x_enable_rx_delay(phydev);
-	else
-		ret = at803x_disable_rx_delay(phydev);
-	if (ret < 0)
-		return ret;
-
-	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
-	    phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID)
-		ret = at803x_enable_tx_delay(phydev);
-	else
-		ret = at803x_disable_tx_delay(phydev);
-	if (ret < 0)
-		return ret;
-
-	ret = at803x_smarteee_config(phydev);
-	if (ret < 0)
-		return ret;
-
-	ret = at803x_clk_out_config(phydev);
-	if (ret < 0)
-		return ret;
-
-	ret = at803x_hibernation_mode_config(phydev);
-	if (ret < 0)
-		return ret;
-
-	/* Ar803x extended next page bit is enabled by default. Cisco
-	 * multigig switches read this bit and attempt to negotiate 10Gbps
-	 * rates even if the next page bit is disabled. This is incorrect
-	 * behaviour but we still need to accommodate it. XNP is only needed
-	 * for 10Gbps support, so disable XNP.
-	 */
-	return phy_modify(phydev, MII_ADVERTISE, MDIO_AN_CTRL1_XNP, 0);
-}
-
-static int at803x_ack_interrupt(struct phy_device *phydev)
-{
-	int err;
-
-	err = phy_read(phydev, AT803X_INTR_STATUS);
-
-	return (err < 0) ? err : 0;
-}
-
-static int at803x_config_intr(struct phy_device *phydev)
-{
-	int err;
-	int value;
-
-	value = phy_read(phydev, AT803X_INTR_ENABLE);
-
-	if (phydev->interrupts == PHY_INTERRUPT_ENABLED) {
-		/* Clear any pending interrupts */
-		err = at803x_ack_interrupt(phydev);
-		if (err)
-			return err;
-
-		value |= AT803X_INTR_ENABLE_AUTONEG_ERR;
-		value |= AT803X_INTR_ENABLE_SPEED_CHANGED;
-		value |= AT803X_INTR_ENABLE_DUPLEX_CHANGED;
-		value |= AT803X_INTR_ENABLE_LINK_FAIL;
-		value |= AT803X_INTR_ENABLE_LINK_SUCCESS;
-
-		err = phy_write(phydev, AT803X_INTR_ENABLE, value);
-	} else {
-		err = phy_write(phydev, AT803X_INTR_ENABLE, 0);
-		if (err)
-			return err;
-
-		/* Clear any pending interrupts */
-		err = at803x_ack_interrupt(phydev);
-	}
-
-	return err;
-}
-
-static irqreturn_t at803x_handle_interrupt(struct phy_device *phydev)
-{
-	int irq_status, int_enabled;
-
-	irq_status = phy_read(phydev, AT803X_INTR_STATUS);
-	if (irq_status < 0) {
-		phy_error(phydev);
-		return IRQ_NONE;
-	}
-
-	/* Read the current enabled interrupts */
-	int_enabled = phy_read(phydev, AT803X_INTR_ENABLE);
-	if (int_enabled < 0) {
-		phy_error(phydev);
-		return IRQ_NONE;
-	}
-
-	/* See if this was one of our enabled interrupts */
-	if (!(irq_status & int_enabled))
-		return IRQ_NONE;
-
-	phy_trigger_machine(phydev);
-
-	return IRQ_HANDLED;
-}
-
-static void at803x_link_change_notify(struct phy_device *phydev)
-{
-	/*
-	 * Conduct a hardware reset for AT8030 every time a link loss is
-	 * signalled. This is necessary to circumvent a hardware bug that
-	 * occurs when the cable is unplugged while TX packets are pending
-	 * in the FIFO. In such cases, the FIFO enters an error mode it
-	 * cannot recover from by software.
-	 */
-	if (phydev->state == PHY_NOLINK && phydev->mdio.reset_gpio) {
-		struct at803x_context context;
-
-		at803x_context_save(phydev, &context);
-
-		phy_device_reset(phydev, 1);
-		usleep_range(1000, 2000);
-		phy_device_reset(phydev, 0);
-		usleep_range(1000, 2000);
-
-		at803x_context_restore(phydev, &context);
-
-		phydev_dbg(phydev, "%s(): phy was reset\n", __func__);
-	}
-}
-
-static int at803x_read_specific_status(struct phy_device *phydev,
-				       struct at803x_ss_mask ss_mask)
-{
-	int ss;
-
-	/* Read the AT8035 PHY-Specific Status register, which indicates the
-	 * speed and duplex that the PHY is actually using, irrespective of
-	 * whether we are in autoneg mode or not.
-	 */
-	ss = phy_read(phydev, AT803X_SPECIFIC_STATUS);
-	if (ss < 0)
-		return ss;
-
-	if (ss & AT803X_SS_SPEED_DUPLEX_RESOLVED) {
-		int sfc, speed;
-
-		sfc = phy_read(phydev, AT803X_SPECIFIC_FUNCTION_CONTROL);
-		if (sfc < 0)
-			return sfc;
-
-		speed = ss & ss_mask.speed_mask;
-		speed >>= ss_mask.speed_shift;
-
-		switch (speed) {
-		case AT803X_SS_SPEED_10:
-			phydev->speed = SPEED_10;
-			break;
-		case AT803X_SS_SPEED_100:
-			phydev->speed = SPEED_100;
-			break;
-		case AT803X_SS_SPEED_1000:
-			phydev->speed = SPEED_1000;
-			break;
-		case QCA808X_SS_SPEED_2500:
-			phydev->speed = SPEED_2500;
-			break;
-		}
-		if (ss & AT803X_SS_DUPLEX)
-			phydev->duplex = DUPLEX_FULL;
-		else
-			phydev->duplex = DUPLEX_HALF;
-
-		if (ss & AT803X_SS_MDIX)
-			phydev->mdix = ETH_TP_MDI_X;
-		else
-			phydev->mdix = ETH_TP_MDI;
-
-		switch (FIELD_GET(AT803X_SFC_MDI_CROSSOVER_MODE_M, sfc)) {
-		case AT803X_SFC_MANUAL_MDI:
-			phydev->mdix_ctrl = ETH_TP_MDI;
-			break;
-		case AT803X_SFC_MANUAL_MDIX:
-			phydev->mdix_ctrl = ETH_TP_MDI_X;
-			break;
-		case AT803X_SFC_AUTOMATIC_CROSSOVER:
-			phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
-			break;
-		}
-	}
-
-	return 0;
-}
-
-static int at803x_read_status(struct phy_device *phydev)
-{
-	struct at803x_ss_mask ss_mask = { 0 };
-	int err, old_link = phydev->link;
-
-	/* Update the link, but return if there was an error */
-	err = genphy_update_link(phydev);
-	if (err)
-		return err;
-
-	/* why bother the PHY if nothing can have changed */
-	if (phydev->autoneg == AUTONEG_ENABLE && old_link && phydev->link)
-		return 0;
-
-	phydev->speed = SPEED_UNKNOWN;
-	phydev->duplex = DUPLEX_UNKNOWN;
-	phydev->pause = 0;
-	phydev->asym_pause = 0;
-
-	err = genphy_read_lpa(phydev);
-	if (err < 0)
-		return err;
-
-	ss_mask.speed_mask = AT803X_SS_SPEED_MASK;
-	ss_mask.speed_shift = __bf_shf(AT803X_SS_SPEED_MASK);
-	err = at803x_read_specific_status(phydev, ss_mask);
-	if (err < 0)
-		return err;
-
-	if (phydev->autoneg == AUTONEG_ENABLE && phydev->autoneg_complete)
-		phy_resolve_aneg_pause(phydev);
-
-	return 0;
-}
-
-static int at803x_config_mdix(struct phy_device *phydev, u8 ctrl)
-{
-	u16 val;
-
-	switch (ctrl) {
-	case ETH_TP_MDI:
-		val = AT803X_SFC_MANUAL_MDI;
-		break;
-	case ETH_TP_MDI_X:
-		val = AT803X_SFC_MANUAL_MDIX;
-		break;
-	case ETH_TP_MDI_AUTO:
-		val = AT803X_SFC_AUTOMATIC_CROSSOVER;
-		break;
-	default:
-		return 0;
-	}
-
-	return phy_modify_changed(phydev, AT803X_SPECIFIC_FUNCTION_CONTROL,
-			  AT803X_SFC_MDI_CROSSOVER_MODE_M,
-			  FIELD_PREP(AT803X_SFC_MDI_CROSSOVER_MODE_M, val));
-}
-
-static int at803x_prepare_config_aneg(struct phy_device *phydev)
-{
-	int ret;
-
-	ret = at803x_config_mdix(phydev, phydev->mdix_ctrl);
-	if (ret < 0)
-		return ret;
-
-	/* Changes of the midx bits are disruptive to the normal operation;
-	 * therefore any changes to these registers must be followed by a
-	 * software reset to take effect.
-	 */
-	if (ret == 1) {
-		ret = genphy_soft_reset(phydev);
-		if (ret < 0)
-			return ret;
-	}
-
-	return 0;
-}
-
-static int at803x_config_aneg(struct phy_device *phydev)
-{
-	struct at803x_priv *priv = phydev->priv;
-	int ret;
-
-	ret = at803x_prepare_config_aneg(phydev);
-	if (ret)
-		return ret;
-
-	if (priv->is_1000basex)
-		return genphy_c37_config_aneg(phydev);
-
-	return genphy_config_aneg(phydev);
-}
-
-static int at803x_get_downshift(struct phy_device *phydev, u8 *d)
-{
-	int val;
-
-	val = phy_read(phydev, AT803X_SMART_SPEED);
-	if (val < 0)
-		return val;
-
-	if (val & AT803X_SMART_SPEED_ENABLE)
-		*d = FIELD_GET(AT803X_SMART_SPEED_RETRY_LIMIT_MASK, val) + 2;
-	else
-		*d = DOWNSHIFT_DEV_DISABLE;
-
-	return 0;
-}
-
-static int at803x_set_downshift(struct phy_device *phydev, u8 cnt)
-{
-	u16 mask, set;
-	int ret;
-
-	switch (cnt) {
-	case DOWNSHIFT_DEV_DEFAULT_COUNT:
-		cnt = AT803X_DEFAULT_DOWNSHIFT;
-		fallthrough;
-	case AT803X_MIN_DOWNSHIFT ... AT803X_MAX_DOWNSHIFT:
-		set = AT803X_SMART_SPEED_ENABLE |
-		      AT803X_SMART_SPEED_BYPASS_TIMER |
-		      FIELD_PREP(AT803X_SMART_SPEED_RETRY_LIMIT_MASK, cnt - 2);
-		mask = AT803X_SMART_SPEED_RETRY_LIMIT_MASK;
-		break;
-	case DOWNSHIFT_DEV_DISABLE:
-		set = 0;
-		mask = AT803X_SMART_SPEED_ENABLE |
-		       AT803X_SMART_SPEED_BYPASS_TIMER;
-		break;
-	default:
-		return -EINVAL;
-	}
-
-	ret = phy_modify_changed(phydev, AT803X_SMART_SPEED, mask, set);
-
-	/* After changing the smart speed settings, we need to perform a
-	 * software reset, use phy_init_hw() to make sure we set the
-	 * reapply any values which might got lost during software reset.
-	 */
-	if (ret == 1)
-		ret = phy_init_hw(phydev);
-
-	return ret;
-}
-
-static int at803x_get_tunable(struct phy_device *phydev,
-			      struct ethtool_tunable *tuna, void *data)
-{
-	switch (tuna->id) {
-	case ETHTOOL_PHY_DOWNSHIFT:
-		return at803x_get_downshift(phydev, data);
-	default:
-		return -EOPNOTSUPP;
-	}
-}
-
-static int at803x_set_tunable(struct phy_device *phydev,
-			      struct ethtool_tunable *tuna, const void *data)
-{
-	switch (tuna->id) {
-	case ETHTOOL_PHY_DOWNSHIFT:
-		return at803x_set_downshift(phydev, *(const u8 *)data);
-	default:
-		return -EOPNOTSUPP;
-	}
-}
-
-static int at803x_cable_test_result_trans(u16 status)
-{
-	switch (FIELD_GET(AT803X_CDT_STATUS_STAT_MASK, status)) {
-	case AT803X_CDT_STATUS_STAT_NORMAL:
-		return ETHTOOL_A_CABLE_RESULT_CODE_OK;
-	case AT803X_CDT_STATUS_STAT_SHORT:
-		return ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT;
-	case AT803X_CDT_STATUS_STAT_OPEN:
-		return ETHTOOL_A_CABLE_RESULT_CODE_OPEN;
-	case AT803X_CDT_STATUS_STAT_FAIL:
-	default:
-		return ETHTOOL_A_CABLE_RESULT_CODE_UNSPEC;
-	}
-}
-
-static bool at803x_cdt_test_failed(u16 status)
-{
-	return FIELD_GET(AT803X_CDT_STATUS_STAT_MASK, status) ==
-		AT803X_CDT_STATUS_STAT_FAIL;
-}
-
-static bool at803x_cdt_fault_length_valid(u16 status)
-{
-	switch (FIELD_GET(AT803X_CDT_STATUS_STAT_MASK, status)) {
-	case AT803X_CDT_STATUS_STAT_OPEN:
-	case AT803X_CDT_STATUS_STAT_SHORT:
-		return true;
-	}
-	return false;
-}
-
-static int at803x_cdt_fault_length(int dt)
-{
-	/* According to the datasheet the distance to the fault is
-	 * DELTA_TIME * 0.824 meters.
-	 *
-	 * The author suspect the correct formula is:
-	 *
-	 *   fault_distance = DELTA_TIME * (c * VF) / 125MHz / 2
-	 *
-	 * where c is the speed of light, VF is the velocity factor of
-	 * the twisted pair cable, 125MHz the counter frequency and
-	 * we need to divide by 2 because the hardware will measure the
-	 * round trip time to the fault and back to the PHY.
-	 *
-	 * With a VF of 0.69 we get the factor 0.824 mentioned in the
-	 * datasheet.
-	 */
-	return (dt * 824) / 10;
-}
-
-static int at803x_cdt_start(struct phy_device *phydev,
-			    u32 cdt_start)
-{
-	return phy_write(phydev, AT803X_CDT, cdt_start);
-}
-
-static int at803x_cdt_wait_for_completion(struct phy_device *phydev,
-					  u32 cdt_en)
-{
-	int val, ret;
-
-	/* One test run takes about 25ms */
-	ret = phy_read_poll_timeout(phydev, AT803X_CDT, val,
-				    !(val & cdt_en),
-				    30000, 100000, true);
-
-	return ret < 0 ? ret : 0;
-}
-
-static int at803x_cable_test_one_pair(struct phy_device *phydev, int pair)
-{
-	static const int ethtool_pair[] = {
-		ETHTOOL_A_CABLE_PAIR_A,
-		ETHTOOL_A_CABLE_PAIR_B,
-		ETHTOOL_A_CABLE_PAIR_C,
-		ETHTOOL_A_CABLE_PAIR_D,
-	};
-	int ret, val;
-
-	val = FIELD_PREP(AT803X_CDT_MDI_PAIR_MASK, pair) |
-	      AT803X_CDT_ENABLE_TEST;
-	ret = at803x_cdt_start(phydev, val);
-	if (ret)
-		return ret;
-
-	ret = at803x_cdt_wait_for_completion(phydev, AT803X_CDT_ENABLE_TEST);
-	if (ret)
-		return ret;
-
-	val = phy_read(phydev, AT803X_CDT_STATUS);
-	if (val < 0)
-		return val;
-
-	if (at803x_cdt_test_failed(val))
-		return 0;
-
-	ethnl_cable_test_result(phydev, ethtool_pair[pair],
-				at803x_cable_test_result_trans(val));
-
-	if (at803x_cdt_fault_length_valid(val)) {
-		val = FIELD_GET(AT803X_CDT_STATUS_DELTA_TIME_MASK, val);
-		ethnl_cable_test_fault_length(phydev, ethtool_pair[pair],
-					      at803x_cdt_fault_length(val));
-	}
-
-	return 1;
-}
-
-static int at803x_cable_test_get_status(struct phy_device *phydev,
-					bool *finished, unsigned long pair_mask)
-{
-	int retries = 20;
-	int pair, ret;
-
-	*finished = false;
-
-	/* According to the datasheet the CDT can be performed when
-	 * there is no link partner or when the link partner is
-	 * auto-negotiating. Starting the test will restart the AN
-	 * automatically. It seems that doing this repeatedly we will
-	 * get a slot where our link partner won't disturb our
-	 * measurement.
-	 */
-	while (pair_mask && retries--) {
-		for_each_set_bit(pair, &pair_mask, 4) {
-			ret = at803x_cable_test_one_pair(phydev, pair);
-			if (ret < 0)
-				return ret;
-			if (ret)
-				clear_bit(pair, &pair_mask);
-		}
-		if (pair_mask)
-			msleep(250);
-	}
-
-	*finished = true;
-
-	return 0;
-}
-
-static void at803x_cable_test_autoneg(struct phy_device *phydev)
-{
-	/* Enable auto-negotiation, but advertise no capabilities, no link
-	 * will be established. A restart of the auto-negotiation is not
-	 * required, because the cable test will automatically break the link.
-	 */
-	phy_write(phydev, MII_BMCR, BMCR_ANENABLE);
-	phy_write(phydev, MII_ADVERTISE, ADVERTISE_CSMA);
-}
-
-static int at803x_cable_test_start(struct phy_device *phydev)
-{
-	at803x_cable_test_autoneg(phydev);
-	/* we do all the (time consuming) work later */
-	return 0;
-}
-
-static int at8031_rgmii_reg_set_voltage_sel(struct regulator_dev *rdev,
-					    unsigned int selector)
-{
-	struct phy_device *phydev = rdev_get_drvdata(rdev);
-
-	if (selector)
-		return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F,
-					     0, AT803X_DEBUG_RGMII_1V8);
-	else
-		return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F,
-					     AT803X_DEBUG_RGMII_1V8, 0);
-}
-
-static int at8031_rgmii_reg_get_voltage_sel(struct regulator_dev *rdev)
-{
-	struct phy_device *phydev = rdev_get_drvdata(rdev);
-	int val;
-
-	val = at803x_debug_reg_read(phydev, AT803X_DEBUG_REG_1F);
-	if (val < 0)
-		return val;
-
-	return (val & AT803X_DEBUG_RGMII_1V8) ? 1 : 0;
-}
-
-static const struct regulator_ops vddio_regulator_ops = {
-	.list_voltage = regulator_list_voltage_table,
-	.set_voltage_sel = at8031_rgmii_reg_set_voltage_sel,
-	.get_voltage_sel = at8031_rgmii_reg_get_voltage_sel,
-};
-
-static const unsigned int vddio_voltage_table[] = {
-	1500000,
-	1800000,
-};
-
-static const struct regulator_desc vddio_desc = {
-	.name = "vddio",
-	.of_match = of_match_ptr("vddio-regulator"),
-	.n_voltages = ARRAY_SIZE(vddio_voltage_table),
-	.volt_table = vddio_voltage_table,
-	.ops = &vddio_regulator_ops,
-	.type = REGULATOR_VOLTAGE,
-	.owner = THIS_MODULE,
-};
-
-static const struct regulator_ops vddh_regulator_ops = {
-};
-
-static const struct regulator_desc vddh_desc = {
-	.name = "vddh",
-	.of_match = of_match_ptr("vddh-regulator"),
-	.n_voltages = 1,
-	.fixed_uV = 2500000,
-	.ops = &vddh_regulator_ops,
-	.type = REGULATOR_VOLTAGE,
-	.owner = THIS_MODULE,
-};
-
-static int at8031_register_regulators(struct phy_device *phydev)
-{
-	struct at803x_priv *priv = phydev->priv;
-	struct device *dev = &phydev->mdio.dev;
-	struct regulator_config config = { };
-
-	config.dev = dev;
-	config.driver_data = phydev;
-
-	priv->vddio_rdev = devm_regulator_register(dev, &vddio_desc, &config);
-	if (IS_ERR(priv->vddio_rdev)) {
-		phydev_err(phydev, "failed to register VDDIO regulator\n");
-		return PTR_ERR(priv->vddio_rdev);
-	}
-
-	priv->vddh_rdev = devm_regulator_register(dev, &vddh_desc, &config);
-	if (IS_ERR(priv->vddh_rdev)) {
-		phydev_err(phydev, "failed to register VDDH regulator\n");
-		return PTR_ERR(priv->vddh_rdev);
-	}
-
-	return 0;
-}
-
-static int at8031_sfp_insert(void *upstream, const struct sfp_eeprom_id *id)
-{
-	struct phy_device *phydev = upstream;
-	__ETHTOOL_DECLARE_LINK_MODE_MASK(phy_support);
-	__ETHTOOL_DECLARE_LINK_MODE_MASK(sfp_support);
-	DECLARE_PHY_INTERFACE_MASK(interfaces);
-	phy_interface_t iface;
-
-	linkmode_zero(phy_support);
-	phylink_set(phy_support, 1000baseX_Full);
-	phylink_set(phy_support, 1000baseT_Full);
-	phylink_set(phy_support, Autoneg);
-	phylink_set(phy_support, Pause);
-	phylink_set(phy_support, Asym_Pause);
-
-	linkmode_zero(sfp_support);
-	sfp_parse_support(phydev->sfp_bus, id, sfp_support, interfaces);
-	/* Some modules support 10G modes as well as others we support.
-	 * Mask out non-supported modes so the correct interface is picked.
-	 */
-	linkmode_and(sfp_support, phy_support, sfp_support);
-
-	if (linkmode_empty(sfp_support)) {
-		dev_err(&phydev->mdio.dev, "incompatible SFP module inserted\n");
-		return -EINVAL;
-	}
-
-	iface = sfp_select_interface(phydev->sfp_bus, sfp_support);
-
-	/* Only 1000Base-X is supported by AR8031/8033 as the downstream SerDes
-	 * interface for use with SFP modules.
-	 * However, some copper modules detected as having a preferred SGMII
-	 * interface do default to and function in 1000Base-X mode, so just
-	 * print a warning and allow such modules, as they may have some chance
-	 * of working.
-	 */
-	if (iface == PHY_INTERFACE_MODE_SGMII)
-		dev_warn(&phydev->mdio.dev, "module may not function if 1000Base-X not supported\n");
-	else if (iface != PHY_INTERFACE_MODE_1000BASEX)
-		return -EINVAL;
-
-	return 0;
-}
-
-static const struct sfp_upstream_ops at8031_sfp_ops = {
-	.attach = phy_sfp_attach,
-	.detach = phy_sfp_detach,
-	.module_insert = at8031_sfp_insert,
-};
-
-static int at8031_parse_dt(struct phy_device *phydev)
-{
-	struct device_node *node = phydev->mdio.dev.of_node;
-	struct at803x_priv *priv = phydev->priv;
-	int ret;
-
-	if (of_property_read_bool(node, "qca,keep-pll-enabled"))
-		priv->flags |= AT803X_KEEP_PLL_ENABLED;
-
-	ret = at8031_register_regulators(phydev);
-	if (ret < 0)
-		return ret;
-
-	ret = devm_regulator_get_enable_optional(&phydev->mdio.dev,
-						 "vddio");
-	if (ret) {
-		phydev_err(phydev, "failed to get VDDIO regulator\n");
-		return ret;
-	}
-
-	/* Only AR8031/8033 support 1000Base-X for SFP modules */
-	return phy_sfp_probe(phydev, &at8031_sfp_ops);
-}
-
-static int at8031_probe(struct phy_device *phydev)
-{
-	struct at803x_priv *priv = phydev->priv;
-	int mode_cfg;
-	int ccr;
-	int ret;
-
-	ret = at803x_probe(phydev);
-	if (ret)
-		return ret;
-
-	/* Only supported on AR8031/AR8033, the AR8030/AR8035 use strapping
-	 * options.
-	 */
-	ret = at8031_parse_dt(phydev);
-	if (ret)
-		return ret;
-
-	ccr = phy_read(phydev, AT803X_REG_CHIP_CONFIG);
-	if (ccr < 0)
-		return ccr;
-	mode_cfg = ccr & AT803X_MODE_CFG_MASK;
-
-	switch (mode_cfg) {
-	case AT803X_MODE_CFG_BX1000_RGMII_50OHM:
-	case AT803X_MODE_CFG_BX1000_RGMII_75OHM:
-		priv->is_1000basex = true;
-		fallthrough;
-	case AT803X_MODE_CFG_FX100_RGMII_50OHM:
-	case AT803X_MODE_CFG_FX100_RGMII_75OHM:
-		priv->is_fiber = true;
-		break;
-	}
-
-	/* Disable WoL in 1588 register which is enabled
-	 * by default
-	 */
-	return phy_modify_mmd(phydev, MDIO_MMD_PCS,
-			      AT803X_PHY_MMD3_WOL_CTRL,
-			      AT803X_WOL_EN, 0);
-}
-
-static int at8031_config_init(struct phy_device *phydev)
-{
-	struct at803x_priv *priv = phydev->priv;
-	int ret;
-
-	/* Some bootloaders leave the fiber page selected.
-	 * Switch to the appropriate page (fiber or copper), as otherwise we
-	 * read the PHY capabilities from the wrong page.
-	 */
-	phy_lock_mdio_bus(phydev);
-	ret = at803x_write_page(phydev,
-				priv->is_fiber ? AT803X_PAGE_FIBER :
-						 AT803X_PAGE_COPPER);
-	phy_unlock_mdio_bus(phydev);
-	if (ret)
-		return ret;
-
-	ret = at8031_pll_config(phydev);
-	if (ret < 0)
-		return ret;
-
-	return at803x_config_init(phydev);
-}
-
-static int at8031_set_wol(struct phy_device *phydev,
-			  struct ethtool_wolinfo *wol)
-{
-	int ret;
-
-	/* First setup MAC address and enable WOL interrupt */
-	ret = at803x_set_wol(phydev, wol);
-	if (ret)
-		return ret;
-
-	if (wol->wolopts & WAKE_MAGIC)
-		/* Enable WOL function for 1588 */
-		ret = phy_modify_mmd(phydev, MDIO_MMD_PCS,
-				     AT803X_PHY_MMD3_WOL_CTRL,
-				     0, AT803X_WOL_EN);
-	else
-		/* Disable WoL function for 1588 */
-		ret = phy_modify_mmd(phydev, MDIO_MMD_PCS,
-				     AT803X_PHY_MMD3_WOL_CTRL,
-				     AT803X_WOL_EN, 0);
-
-	return ret;
-}
-
-static int at8031_config_intr(struct phy_device *phydev)
-{
-	struct at803x_priv *priv = phydev->priv;
-	int err, value = 0;
-
-	if (phydev->interrupts == PHY_INTERRUPT_ENABLED &&
-	    priv->is_fiber) {
-		/* Clear any pending interrupts */
-		err = at803x_ack_interrupt(phydev);
-		if (err)
-			return err;
-
-		value |= AT803X_INTR_ENABLE_LINK_FAIL_BX;
-		value |= AT803X_INTR_ENABLE_LINK_SUCCESS_BX;
-
-		err = phy_set_bits(phydev, AT803X_INTR_ENABLE, value);
-		if (err)
-			return err;
-	}
-
-	return at803x_config_intr(phydev);
-}
-
-/* AR8031 and AR8033 share the same read status logic */
-static int at8031_read_status(struct phy_device *phydev)
-{
-	struct at803x_priv *priv = phydev->priv;
-
-	if (priv->is_1000basex)
-		return genphy_c37_read_status(phydev);
-
-	return at803x_read_status(phydev);
-}
-
-/* AR8031 and AR8035 share the same cable test get status reg */
-static int at8031_cable_test_get_status(struct phy_device *phydev,
-					bool *finished)
-{
-	return at803x_cable_test_get_status(phydev, finished, 0xf);
-}
-
-/* AR8031 and AR8035 share the same cable test start logic */
-static int at8031_cable_test_start(struct phy_device *phydev)
-{
-	at803x_cable_test_autoneg(phydev);
-	phy_write(phydev, MII_CTRL1000, 0);
-	/* we do all the (time consuming) work later */
-	return 0;
-}
-
-/* AR8032, AR9331 and QCA9561 share the same cable test get status reg */
-static int at8032_cable_test_get_status(struct phy_device *phydev,
-					bool *finished)
-{
-	return at803x_cable_test_get_status(phydev, finished, 0x3);
-}
-
-static int at8035_parse_dt(struct phy_device *phydev)
-{
-	struct at803x_priv *priv = phydev->priv;
-
-	/* Mask is set by the generic at803x_parse_dt
-	 * if property is set. Assume property is set
-	 * with the mask not zero.
-	 */
-	if (priv->clk_25m_mask) {
-		/* Fixup for the AR8030/AR8035. This chip has another mask and
-		 * doesn't support the DSP reference. Eg. the lowest bit of the
-		 * mask. The upper two bits select the same frequencies. Mask
-		 * the lowest bit here.
-		 *
-		 * Warning:
-		 *   There was no datasheet for the AR8030 available so this is
-		 *   just a guess. But the AR8035 is listed as pin compatible
-		 *   to the AR8030 so there might be a good chance it works on
-		 *   the AR8030 too.
-		 */
-		priv->clk_25m_reg &= AT8035_CLK_OUT_MASK;
-		priv->clk_25m_mask &= AT8035_CLK_OUT_MASK;
-	}
-
-	return 0;
-}
-
-/* AR8030 and AR8035 shared the same special mask for clk_25m */
-static int at8035_probe(struct phy_device *phydev)
-{
-	int ret;
-
-	ret = at803x_probe(phydev);
-	if (ret)
-		return ret;
-
-	return at8035_parse_dt(phydev);
-}
-
-static int qca83xx_config_init(struct phy_device *phydev)
-{
-	u8 switch_revision;
-
-	switch_revision = phydev->dev_flags & QCA8K_DEVFLAGS_REVISION_MASK;
-
-	switch (switch_revision) {
-	case 1:
-		/* For 100M waveform */
-		at803x_debug_reg_write(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL, 0x02ea);
-		/* Turn on Gigabit clock */
-		at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_GREEN, 0x68a0);
-		break;
-
-	case 2:
-		phy_write_mmd(phydev, MDIO_MMD_AN, MDIO_AN_EEE_ADV, 0x0);
-		fallthrough;
-	case 4:
-		phy_write_mmd(phydev, MDIO_MMD_PCS, MDIO_AZ_DEBUG, 0x803f);
-		at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_GREEN, 0x6860);
-		at803x_debug_reg_write(phydev, AT803X_DEBUG_SYSTEM_CTRL_MODE, 0x2c46);
-		at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_3C, 0x6000);
-		break;
-	}
-
-	/* Following original QCA sourcecode set port to prefer master */
-	phy_set_bits(phydev, MII_CTRL1000, CTL1000_PREFER_MASTER);
-
-	return 0;
-}
-
-static int qca8327_config_init(struct phy_device *phydev)
-{
-	/* QCA8327 require DAC amplitude adjustment for 100m set to +6%.
-	 * Disable on init and enable only with 100m speed following
-	 * qca original source code.
-	 */
-	at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL,
-			      QCA8327_DEBUG_MANU_CTRL_EN, 0);
-
-	return qca83xx_config_init(phydev);
-}
-
-static void qca83xx_link_change_notify(struct phy_device *phydev)
-{
-	/* Set DAC Amplitude adjustment to +6% for 100m on link running */
-	if (phydev->state == PHY_RUNNING) {
-		if (phydev->speed == SPEED_100)
-			at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL,
-					      QCA8327_DEBUG_MANU_CTRL_EN,
-					      QCA8327_DEBUG_MANU_CTRL_EN);
-	} else {
-		/* Reset DAC Amplitude adjustment */
-		at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL,
-				      QCA8327_DEBUG_MANU_CTRL_EN, 0);
-	}
-}
-
-static int qca83xx_resume(struct phy_device *phydev)
-{
-	int ret, val;
-
-	/* Skip reset if not suspended */
-	if (!phydev->suspended)
-		return 0;
-
-	/* Reinit the port, reset values set by suspend */
-	qca83xx_config_init(phydev);
-
-	/* Reset the port on port resume */
-	phy_set_bits(phydev, MII_BMCR, BMCR_RESET | BMCR_ANENABLE);
-
-	/* On resume from suspend the switch execute a reset and
-	 * restart auto-negotiation. Wait for reset to complete.
-	 */
-	ret = phy_read_poll_timeout(phydev, MII_BMCR, val, !(val & BMCR_RESET),
-				    50000, 600000, true);
-	if (ret)
-		return ret;
-
-	usleep_range(1000, 2000);
-
-	return 0;
-}
-
-static int qca83xx_suspend(struct phy_device *phydev)
-{
-	at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_GREEN,
-			      AT803X_DEBUG_GATE_CLK_IN1000, 0);
-
-	at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_HIB_CTRL,
-			      AT803X_DEBUG_HIB_CTRL_EN_ANY_CHANGE |
-			      AT803X_DEBUG_HIB_CTRL_SEL_RST_80U, 0);
-
-	return 0;
-}
-
-static int qca8337_suspend(struct phy_device *phydev)
-{
-	/* Only QCA8337 support actual suspend. */
-	genphy_suspend(phydev);
-
-	return qca83xx_suspend(phydev);
-}
-
-static int qca8327_suspend(struct phy_device *phydev)
-{
-	u16 mask = 0;
-
-	/* QCA8327 cause port unreliability when phy suspend
-	 * is set.
-	 */
-	mask |= ~(BMCR_SPEED1000 | BMCR_FULLDPLX);
-	phy_modify(phydev, MII_BMCR, mask, 0);
-
-	return qca83xx_suspend(phydev);
-}
-
-static int qca808x_phy_fast_retrain_config(struct phy_device *phydev)
-{
-	int ret;
-
-	/* Enable fast retrain */
-	ret = genphy_c45_fast_retrain(phydev, true);
-	if (ret)
-		return ret;
-
-	phy_write_mmd(phydev, MDIO_MMD_AN, QCA808X_PHY_MMD7_TOP_OPTION1,
-		      QCA808X_TOP_OPTION1_DATA);
-	phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_20DB,
-		      QCA808X_MSE_THRESHOLD_20DB_VALUE);
-	phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_17DB,
-		      QCA808X_MSE_THRESHOLD_17DB_VALUE);
-	phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_27DB,
-		      QCA808X_MSE_THRESHOLD_27DB_VALUE);
-	phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_28DB,
-		      QCA808X_MSE_THRESHOLD_28DB_VALUE);
-	phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_1,
-		      QCA808X_MMD3_DEBUG_1_VALUE);
-	phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_4,
-		      QCA808X_MMD3_DEBUG_4_VALUE);
-	phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_5,
-		      QCA808X_MMD3_DEBUG_5_VALUE);
-	phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_3,
-		      QCA808X_MMD3_DEBUG_3_VALUE);
-	phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_6,
-		      QCA808X_MMD3_DEBUG_6_VALUE);
-	phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_2,
-		      QCA808X_MMD3_DEBUG_2_VALUE);
-
-	return 0;
-}
-
-static int qca808x_phy_ms_seed_enable(struct phy_device *phydev, bool enable)
-{
-	u16 seed_value;
-
-	if (!enable)
-		return at803x_debug_reg_mask(phydev, QCA808X_PHY_DEBUG_LOCAL_SEED,
-				QCA808X_MASTER_SLAVE_SEED_ENABLE, 0);
-
-	seed_value = get_random_u32_below(QCA808X_MASTER_SLAVE_SEED_RANGE);
-	return at803x_debug_reg_mask(phydev, QCA808X_PHY_DEBUG_LOCAL_SEED,
-			QCA808X_MASTER_SLAVE_SEED_CFG | QCA808X_MASTER_SLAVE_SEED_ENABLE,
-			FIELD_PREP(QCA808X_MASTER_SLAVE_SEED_CFG, seed_value) |
-			QCA808X_MASTER_SLAVE_SEED_ENABLE);
-}
-
-static bool qca808x_is_prefer_master(struct phy_device *phydev)
-{
-	return (phydev->master_slave_get == MASTER_SLAVE_CFG_MASTER_FORCE) ||
-		(phydev->master_slave_get == MASTER_SLAVE_CFG_MASTER_PREFERRED);
-}
-
-static bool qca808x_has_fast_retrain_or_slave_seed(struct phy_device *phydev)
-{
-	return linkmode_test_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->supported);
-}
-
-static int qca808x_config_init(struct phy_device *phydev)
-{
-	int ret;
-
-	/* Active adc&vga on 802.3az for the link 1000M and 100M */
-	ret = phy_modify_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_ADDR_CLD_CTRL7,
-			     QCA808X_8023AZ_AFE_CTRL_MASK, QCA808X_8023AZ_AFE_EN);
-	if (ret)
-		return ret;
-
-	/* Adjust the threshold on 802.3az for the link 1000M */
-	ret = phy_write_mmd(phydev, MDIO_MMD_PCS,
-			    QCA808X_PHY_MMD3_AZ_TRAINING_CTRL,
-			    QCA808X_MMD3_AZ_TRAINING_VAL);
-	if (ret)
-		return ret;
-
-	if (qca808x_has_fast_retrain_or_slave_seed(phydev)) {
-		/* Config the fast retrain for the link 2500M */
-		ret = qca808x_phy_fast_retrain_config(phydev);
-		if (ret)
-			return ret;
-
-		ret = genphy_read_master_slave(phydev);
-		if (ret < 0)
-			return ret;
-
-		if (!qca808x_is_prefer_master(phydev)) {
-			/* Enable seed and configure lower ramdom seed to make phy
-			 * linked as slave mode.
-			 */
-			ret = qca808x_phy_ms_seed_enable(phydev, true);
-			if (ret)
-				return ret;
-		}
-	}
-
-	/* Configure adc threshold as 100mv for the link 10M */
-	return at803x_debug_reg_mask(phydev, QCA808X_PHY_DEBUG_ADC_THRESHOLD,
-				     QCA808X_ADC_THRESHOLD_MASK,
-				     QCA808X_ADC_THRESHOLD_100MV);
-}
-
-static int qca808x_read_status(struct phy_device *phydev)
-{
-	struct at803x_ss_mask ss_mask = { 0 };
-	int ret;
-
-	ret = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_AN_10GBT_STAT);
-	if (ret < 0)
-		return ret;
-
-	linkmode_mod_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->lp_advertising,
-			 ret & MDIO_AN_10GBT_STAT_LP2_5G);
-
-	ret = genphy_read_status(phydev);
-	if (ret)
-		return ret;
-
-	/* qca8081 takes the different bits for speed value from at803x */
-	ss_mask.speed_mask = QCA808X_SS_SPEED_MASK;
-	ss_mask.speed_shift = __bf_shf(QCA808X_SS_SPEED_MASK);
-	ret = at803x_read_specific_status(phydev, ss_mask);
-	if (ret < 0)
-		return ret;
-
-	if (phydev->link) {
-		if (phydev->speed == SPEED_2500)
-			phydev->interface = PHY_INTERFACE_MODE_2500BASEX;
-		else
-			phydev->interface = PHY_INTERFACE_MODE_SGMII;
-	} else {
-		/* generate seed as a lower random value to make PHY linked as SLAVE easily,
-		 * except for master/slave configuration fault detected or the master mode
-		 * preferred.
-		 *
-		 * the reason for not putting this code into the function link_change_notify is
-		 * the corner case where the link partner is also the qca8081 PHY and the seed
-		 * value is configured as the same value, the link can't be up and no link change
-		 * occurs.
-		 */
-		if (qca808x_has_fast_retrain_or_slave_seed(phydev)) {
-			if (phydev->master_slave_state == MASTER_SLAVE_STATE_ERR ||
-			    qca808x_is_prefer_master(phydev)) {
-				qca808x_phy_ms_seed_enable(phydev, false);
-			} else {
-				qca808x_phy_ms_seed_enable(phydev, true);
-			}
-		}
-	}
-
-	return 0;
-}
-
-static int qca808x_soft_reset(struct phy_device *phydev)
-{
-	int ret;
-
-	ret = genphy_soft_reset(phydev);
-	if (ret < 0)
-		return ret;
-
-	if (qca808x_has_fast_retrain_or_slave_seed(phydev))
-		ret = qca808x_phy_ms_seed_enable(phydev, true);
-
-	return ret;
-}
-
-static bool qca808x_cdt_fault_length_valid(int cdt_code)
-{
-	switch (cdt_code) {
-	case QCA808X_CDT_STATUS_STAT_SAME_SHORT:
-	case QCA808X_CDT_STATUS_STAT_SAME_OPEN:
-	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_NORMAL:
-	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_OPEN:
-	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_SHORT:
-	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_NORMAL:
-	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_OPEN:
-	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_SHORT:
-	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_NORMAL:
-	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_OPEN:
-	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_SHORT:
-		return true;
-	default:
-		return false;
-	}
-}
-
-static int qca808x_cable_test_result_trans(int cdt_code)
-{
-	switch (cdt_code) {
-	case QCA808X_CDT_STATUS_STAT_NORMAL:
-		return ETHTOOL_A_CABLE_RESULT_CODE_OK;
-	case QCA808X_CDT_STATUS_STAT_SAME_SHORT:
-		return ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT;
-	case QCA808X_CDT_STATUS_STAT_SAME_OPEN:
-		return ETHTOOL_A_CABLE_RESULT_CODE_OPEN;
-	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_NORMAL:
-	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_OPEN:
-	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_SHORT:
-	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_NORMAL:
-	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_OPEN:
-	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_SHORT:
-	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_NORMAL:
-	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_OPEN:
-	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_SHORT:
-		return ETHTOOL_A_CABLE_RESULT_CODE_CROSS_SHORT;
-	case QCA808X_CDT_STATUS_STAT_FAIL:
-	default:
-		return ETHTOOL_A_CABLE_RESULT_CODE_UNSPEC;
-	}
-}
-
-static int qca808x_cdt_fault_length(struct phy_device *phydev, int pair,
-				    int result)
-{
-	int val;
-	u32 cdt_length_reg = 0;
-
-	switch (pair) {
-	case ETHTOOL_A_CABLE_PAIR_A:
-		cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_A;
-		break;
-	case ETHTOOL_A_CABLE_PAIR_B:
-		cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_B;
-		break;
-	case ETHTOOL_A_CABLE_PAIR_C:
-		cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_C;
-		break;
-	case ETHTOOL_A_CABLE_PAIR_D:
-		cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_D;
-		break;
-	default:
-		return -EINVAL;
-	}
-
-	val = phy_read_mmd(phydev, MDIO_MMD_PCS, cdt_length_reg);
-	if (val < 0)
-		return val;
-
-	if (result == ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT)
-		val = FIELD_GET(QCA808X_CDT_DIAG_LENGTH_SAME_SHORT, val);
-	else
-		val = FIELD_GET(QCA808X_CDT_DIAG_LENGTH_CROSS_SHORT, val);
-
-	return at803x_cdt_fault_length(val);
-}
-
-static int qca808x_cable_test_start(struct phy_device *phydev)
-{
-	int ret;
-
-	/* perform CDT with the following configs:
-	 * 1. disable hibernation.
-	 * 2. force PHY working in MDI mode.
-	 * 3. for PHY working in 1000BaseT.
-	 * 4. configure the threshold.
-	 */
-
-	ret = at803x_debug_reg_mask(phydev, QCA808X_DBG_AN_TEST, QCA808X_HIBERNATION_EN, 0);
-	if (ret < 0)
-		return ret;
-
-	ret = at803x_config_mdix(phydev, ETH_TP_MDI);
-	if (ret < 0)
-		return ret;
-
-	/* Force 1000base-T needs to configure PMA/PMD and MII_BMCR */
-	phydev->duplex = DUPLEX_FULL;
-	phydev->speed = SPEED_1000;
-	ret = genphy_c45_pma_setup_forced(phydev);
-	if (ret < 0)
-		return ret;
-
-	ret = genphy_setup_forced(phydev);
-	if (ret < 0)
-		return ret;
-
-	/* configure the thresholds for open, short, pair ok test */
-	phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8074, 0xc040);
-	phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8076, 0xc040);
-	phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8077, 0xa060);
-	phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8078, 0xc050);
-	phy_write_mmd(phydev, MDIO_MMD_PCS, 0x807a, 0xc060);
-	phy_write_mmd(phydev, MDIO_MMD_PCS, 0x807e, 0xb060);
-
-	return 0;
-}
-
-static int qca808x_cable_test_get_pair_status(struct phy_device *phydev, u8 pair,
-					      u16 status)
-{
-	int length, result;
-	u16 pair_code;
-
-	switch (pair) {
-	case ETHTOOL_A_CABLE_PAIR_A:
-		pair_code = FIELD_GET(QCA808X_CDT_CODE_PAIR_A, status);
-		break;
-	case ETHTOOL_A_CABLE_PAIR_B:
-		pair_code = FIELD_GET(QCA808X_CDT_CODE_PAIR_B, status);
-		break;
-	case ETHTOOL_A_CABLE_PAIR_C:
-		pair_code = FIELD_GET(QCA808X_CDT_CODE_PAIR_C, status);
-		break;
-	case ETHTOOL_A_CABLE_PAIR_D:
-		pair_code = FIELD_GET(QCA808X_CDT_CODE_PAIR_D, status);
-		break;
-	default:
-		return -EINVAL;
-	}
-
-	result = qca808x_cable_test_result_trans(pair_code);
-	ethnl_cable_test_result(phydev, pair, result);
-
-	if (qca808x_cdt_fault_length_valid(pair_code)) {
-		length = qca808x_cdt_fault_length(phydev, pair, result);
-		ethnl_cable_test_fault_length(phydev, pair, length);
-	}
-
-	return 0;
-}
-
-static int qca808x_cable_test_get_status(struct phy_device *phydev, bool *finished)
-{
-	int ret, val;
-
-	*finished = false;
-
-	val = QCA808X_CDT_ENABLE_TEST |
-	      QCA808X_CDT_LENGTH_UNIT;
-	ret = at803x_cdt_start(phydev, val);
-	if (ret)
-		return ret;
-
-	ret = at803x_cdt_wait_for_completion(phydev, QCA808X_CDT_ENABLE_TEST);
-	if (ret)
-		return ret;
-
-	val = phy_read_mmd(phydev, MDIO_MMD_PCS, QCA808X_MMD3_CDT_STATUS);
-	if (val < 0)
-		return val;
-
-	ret = qca808x_cable_test_get_pair_status(phydev, ETHTOOL_A_CABLE_PAIR_A, val);
-	if (ret)
-		return ret;
-
-	ret = qca808x_cable_test_get_pair_status(phydev, ETHTOOL_A_CABLE_PAIR_B, val);
-	if (ret)
-		return ret;
-
-	ret = qca808x_cable_test_get_pair_status(phydev, ETHTOOL_A_CABLE_PAIR_C, val);
-	if (ret)
-		return ret;
-
-	ret = qca808x_cable_test_get_pair_status(phydev, ETHTOOL_A_CABLE_PAIR_D, val);
-	if (ret)
-		return ret;
-
-	*finished = true;
-
-	return 0;
-}
-
-static int qca808x_get_features(struct phy_device *phydev)
-{
-	int ret;
-
-	ret = genphy_c45_pma_read_abilities(phydev);
-	if (ret)
-		return ret;
-
-	/* The autoneg ability is not existed in bit3 of MMD7.1,
-	 * but it is supported by qca808x PHY, so we add it here
-	 * manually.
-	 */
-	linkmode_set_bit(ETHTOOL_LINK_MODE_Autoneg_BIT, phydev->supported);
-
-	/* As for the qca8081 1G version chip, the 2500baseT ability is also
-	 * existed in the bit0 of MMD1.21, we need to remove it manually if
-	 * it is the qca8081 1G chip according to the bit0 of MMD7.0x901d.
-	 */
-	ret = phy_read_mmd(phydev, MDIO_MMD_AN, QCA808X_PHY_MMD7_CHIP_TYPE);
-	if (ret < 0)
-		return ret;
-
-	if (QCA808X_PHY_CHIP_TYPE_1G & ret)
-		linkmode_clear_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->supported);
-
-	return 0;
-}
-
-static int qca808x_config_aneg(struct phy_device *phydev)
-{
-	int phy_ctrl = 0;
-	int ret;
-
-	ret = at803x_prepare_config_aneg(phydev);
-	if (ret)
-		return ret;
-
-	/* The reg MII_BMCR also needs to be configured for force mode, the
-	 * genphy_config_aneg is also needed.
-	 */
-	if (phydev->autoneg == AUTONEG_DISABLE)
-		genphy_c45_pma_setup_forced(phydev);
-
-	if (linkmode_test_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->advertising))
-		phy_ctrl = MDIO_AN_10GBT_CTRL_ADV2_5G;
-
-	ret = phy_modify_mmd_changed(phydev, MDIO_MMD_AN, MDIO_AN_10GBT_CTRL,
-				     MDIO_AN_10GBT_CTRL_ADV2_5G, phy_ctrl);
-	if (ret < 0)
-		return ret;
-
-	return __genphy_config_aneg(phydev, ret);
-}
-
-static void qca808x_link_change_notify(struct phy_device *phydev)
-{
-	/* Assert interface sgmii fifo on link down, deassert it on link up,
-	 * the interface device address is always phy address added by 1.
-	 */
-	mdiobus_c45_modify_changed(phydev->mdio.bus, phydev->mdio.addr + 1,
-				   MDIO_MMD_PMAPMD, QCA8081_PHY_SERDES_MMD1_FIFO_CTRL,
-				   QCA8081_PHY_FIFO_RSTN,
-				   phydev->link ? QCA8081_PHY_FIFO_RSTN : 0);
-}
-
-static int qca808x_led_parse_netdev(struct phy_device *phydev, unsigned long rules,
-				    u16 *offload_trigger)
-{
-	/* Parsing specific to netdev trigger */
-	if (test_bit(TRIGGER_NETDEV_TX, &rules))
-		*offload_trigger |= QCA808X_LED_TX_BLINK;
-	if (test_bit(TRIGGER_NETDEV_RX, &rules))
-		*offload_trigger |= QCA808X_LED_RX_BLINK;
-	if (test_bit(TRIGGER_NETDEV_LINK_10, &rules))
-		*offload_trigger |= QCA808X_LED_SPEED10_ON;
-	if (test_bit(TRIGGER_NETDEV_LINK_100, &rules))
-		*offload_trigger |= QCA808X_LED_SPEED100_ON;
-	if (test_bit(TRIGGER_NETDEV_LINK_1000, &rules))
-		*offload_trigger |= QCA808X_LED_SPEED1000_ON;
-	if (test_bit(TRIGGER_NETDEV_LINK_2500, &rules))
-		*offload_trigger |= QCA808X_LED_SPEED2500_ON;
-	if (test_bit(TRIGGER_NETDEV_HALF_DUPLEX, &rules))
-		*offload_trigger |= QCA808X_LED_HALF_DUPLEX_ON;
-	if (test_bit(TRIGGER_NETDEV_FULL_DUPLEX, &rules))
-		*offload_trigger |= QCA808X_LED_FULL_DUPLEX_ON;
-
-	if (rules && !*offload_trigger)
-		return -EOPNOTSUPP;
-
-	/* Enable BLINK_CHECK_BYPASS by default to make the LED
-	 * blink even with duplex or speed mode not enabled.
-	 */
-	*offload_trigger |= QCA808X_LED_BLINK_CHECK_BYPASS;
-
-	return 0;
-}
-
-static int qca808x_led_hw_control_enable(struct phy_device *phydev, u8 index)
-{
-	u16 reg;
-
-	if (index > 2)
-		return -EINVAL;
-
-	reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
-
-	return phy_clear_bits_mmd(phydev, MDIO_MMD_AN, reg,
-				  QCA808X_LED_FORCE_EN);
-}
-
-static int qca808x_led_hw_is_supported(struct phy_device *phydev, u8 index,
-				       unsigned long rules)
-{
-	u16 offload_trigger = 0;
-
-	if (index > 2)
-		return -EINVAL;
-
-	return qca808x_led_parse_netdev(phydev, rules, &offload_trigger);
-}
-
-static int qca808x_led_hw_control_set(struct phy_device *phydev, u8 index,
-				      unsigned long rules)
-{
-	u16 reg, offload_trigger = 0;
-	int ret;
-
-	if (index > 2)
-		return -EINVAL;
-
-	reg = QCA808X_MMD7_LED_CTRL(index);
-
-	ret = qca808x_led_parse_netdev(phydev, rules, &offload_trigger);
-	if (ret)
-		return ret;
-
-	ret = qca808x_led_hw_control_enable(phydev, index);
-	if (ret)
-		return ret;
-
-	return phy_modify_mmd(phydev, MDIO_MMD_AN, reg,
-			      QCA808X_LED_PATTERN_MASK,
-			      offload_trigger);
-}
-
-static bool qca808x_led_hw_control_status(struct phy_device *phydev, u8 index)
-{
-	u16 reg;
-	int val;
-
-	if (index > 2)
-		return false;
-
-	reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
-
-	val = phy_read_mmd(phydev, MDIO_MMD_AN, reg);
-
-	return !(val & QCA808X_LED_FORCE_EN);
-}
-
-static int qca808x_led_hw_control_get(struct phy_device *phydev, u8 index,
-				      unsigned long *rules)
-{
-	u16 reg;
-	int val;
-
-	if (index > 2)
-		return -EINVAL;
-
-	/* Check if we have hw control enabled */
-	if (qca808x_led_hw_control_status(phydev, index))
-		return -EINVAL;
-
-	reg = QCA808X_MMD7_LED_CTRL(index);
-
-	val = phy_read_mmd(phydev, MDIO_MMD_AN, reg);
-	if (val & QCA808X_LED_TX_BLINK)
-		set_bit(TRIGGER_NETDEV_TX, rules);
-	if (val & QCA808X_LED_RX_BLINK)
-		set_bit(TRIGGER_NETDEV_RX, rules);
-	if (val & QCA808X_LED_SPEED10_ON)
-		set_bit(TRIGGER_NETDEV_LINK_10, rules);
-	if (val & QCA808X_LED_SPEED100_ON)
-		set_bit(TRIGGER_NETDEV_LINK_100, rules);
-	if (val & QCA808X_LED_SPEED1000_ON)
-		set_bit(TRIGGER_NETDEV_LINK_1000, rules);
-	if (val & QCA808X_LED_SPEED2500_ON)
-		set_bit(TRIGGER_NETDEV_LINK_2500, rules);
-	if (val & QCA808X_LED_HALF_DUPLEX_ON)
-		set_bit(TRIGGER_NETDEV_HALF_DUPLEX, rules);
-	if (val & QCA808X_LED_FULL_DUPLEX_ON)
-		set_bit(TRIGGER_NETDEV_FULL_DUPLEX, rules);
-
-	return 0;
-}
-
-static int qca808x_led_hw_control_reset(struct phy_device *phydev, u8 index)
-{
-	u16 reg;
-
-	if (index > 2)
-		return -EINVAL;
-
-	reg = QCA808X_MMD7_LED_CTRL(index);
-
-	return phy_clear_bits_mmd(phydev, MDIO_MMD_AN, reg,
-				  QCA808X_LED_PATTERN_MASK);
-}
-
-static int qca808x_led_brightness_set(struct phy_device *phydev,
-				      u8 index, enum led_brightness value)
-{
-	u16 reg;
-	int ret;
-
-	if (index > 2)
-		return -EINVAL;
-
-	if (!value) {
-		ret = qca808x_led_hw_control_reset(phydev, index);
-		if (ret)
-			return ret;
-	}
-
-	reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
-
-	return phy_modify_mmd(phydev, MDIO_MMD_AN, reg,
-			      QCA808X_LED_FORCE_EN | QCA808X_LED_FORCE_MODE_MASK,
-			      QCA808X_LED_FORCE_EN | value ? QCA808X_LED_FORCE_ON :
-							     QCA808X_LED_FORCE_OFF);
-}
-
-static int qca808x_led_blink_set(struct phy_device *phydev, u8 index,
-				 unsigned long *delay_on,
-				 unsigned long *delay_off)
-{
-	int ret;
-	u16 reg;
-
-	if (index > 2)
-		return -EINVAL;
-
-	reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
-
-	/* Set blink to 50% off, 50% on at 4Hz by default */
-	ret = phy_modify_mmd(phydev, MDIO_MMD_AN, QCA808X_MMD7_LED_GLOBAL,
-			     QCA808X_LED_BLINK_FREQ_MASK | QCA808X_LED_BLINK_DUTY_MASK,
-			     QCA808X_LED_BLINK_FREQ_4HZ | QCA808X_LED_BLINK_DUTY_50_50);
-	if (ret)
-		return ret;
-
-	/* We use BLINK_1 for normal blinking */
-	ret = phy_modify_mmd(phydev, MDIO_MMD_AN, reg,
-			     QCA808X_LED_FORCE_EN | QCA808X_LED_FORCE_MODE_MASK,
-			     QCA808X_LED_FORCE_EN | QCA808X_LED_FORCE_BLINK_1);
-	if (ret)
-		return ret;
-
-	/* We set blink to 4Hz, aka 250ms */
-	*delay_on = 250 / 2;
-	*delay_off = 250 / 2;
-
-	return 0;
-}
-
-static int qca808x_led_polarity_set(struct phy_device *phydev, int index,
-				    unsigned long modes)
-{
-	struct at803x_priv *priv = phydev->priv;
-	bool active_low = false;
-	u32 mode;
-
-	for_each_set_bit(mode, &modes, __PHY_LED_MODES_NUM) {
-		switch (mode) {
-		case PHY_LED_ACTIVE_LOW:
-			active_low = true;
-			break;
-		default:
-			return -EINVAL;
-		}
-	}
-
-	/* PHY polarity is global and can't be set per LED.
-	 * To detect this, check if last requested polarity mode
-	 * match the new one.
-	 */
-	if (priv->led_polarity_mode >= 0 &&
-	    priv->led_polarity_mode != active_low) {
-		phydev_err(phydev, "PHY polarity is global. Mismatched polarity on different LED\n");
-		return -EINVAL;
-	}
-
-	/* Save the last PHY polarity mode */
-	priv->led_polarity_mode = active_low;
-
-	return phy_modify_mmd(phydev, MDIO_MMD_AN,
-			      QCA808X_MMD7_LED_POLARITY_CTRL,
-			      QCA808X_LED_ACTIVE_HIGH,
-			      active_low ? 0 : QCA808X_LED_ACTIVE_HIGH);
-}
-
-static struct phy_driver at803x_driver[] = {
-{
-	/* Qualcomm Atheros AR8035 */
-	PHY_ID_MATCH_EXACT(ATH8035_PHY_ID),
-	.name			= "Qualcomm Atheros AR8035",
-	.flags			= PHY_POLL_CABLE_TEST,
-	.probe			= at8035_probe,
-	.config_aneg		= at803x_config_aneg,
-	.config_init		= at803x_config_init,
-	.soft_reset		= genphy_soft_reset,
-	.set_wol		= at803x_set_wol,
-	.get_wol		= at803x_get_wol,
-	.suspend		= at803x_suspend,
-	.resume			= at803x_resume,
-	/* PHY_GBIT_FEATURES */
-	.read_status		= at803x_read_status,
-	.config_intr		= at803x_config_intr,
-	.handle_interrupt	= at803x_handle_interrupt,
-	.get_tunable		= at803x_get_tunable,
-	.set_tunable		= at803x_set_tunable,
-	.cable_test_start	= at8031_cable_test_start,
-	.cable_test_get_status	= at8031_cable_test_get_status,
-}, {
-	/* Qualcomm Atheros AR8030 */
-	.phy_id			= ATH8030_PHY_ID,
-	.name			= "Qualcomm Atheros AR8030",
-	.phy_id_mask		= AT8030_PHY_ID_MASK,
-	.probe			= at8035_probe,
-	.config_init		= at803x_config_init,
-	.link_change_notify	= at803x_link_change_notify,
-	.set_wol		= at803x_set_wol,
-	.get_wol		= at803x_get_wol,
-	.suspend		= at803x_suspend,
-	.resume			= at803x_resume,
-	/* PHY_BASIC_FEATURES */
-	.config_intr		= at803x_config_intr,
-	.handle_interrupt	= at803x_handle_interrupt,
-}, {
-	/* Qualcomm Atheros AR8031/AR8033 */
-	PHY_ID_MATCH_EXACT(ATH8031_PHY_ID),
-	.name			= "Qualcomm Atheros AR8031/AR8033",
-	.flags			= PHY_POLL_CABLE_TEST,
-	.probe			= at8031_probe,
-	.config_init		= at8031_config_init,
-	.config_aneg		= at803x_config_aneg,
-	.soft_reset		= genphy_soft_reset,
-	.set_wol		= at8031_set_wol,
-	.get_wol		= at803x_get_wol,
-	.suspend		= at803x_suspend,
-	.resume			= at803x_resume,
-	.read_page		= at803x_read_page,
-	.write_page		= at803x_write_page,
-	.get_features		= at803x_get_features,
-	.read_status		= at8031_read_status,
-	.config_intr		= at8031_config_intr,
-	.handle_interrupt	= at803x_handle_interrupt,
-	.get_tunable		= at803x_get_tunable,
-	.set_tunable		= at803x_set_tunable,
-	.cable_test_start	= at8031_cable_test_start,
-	.cable_test_get_status	= at8031_cable_test_get_status,
-}, {
-	/* Qualcomm Atheros AR8032 */
-	PHY_ID_MATCH_EXACT(ATH8032_PHY_ID),
-	.name			= "Qualcomm Atheros AR8032",
-	.probe			= at803x_probe,
-	.flags			= PHY_POLL_CABLE_TEST,
-	.config_init		= at803x_config_init,
-	.link_change_notify	= at803x_link_change_notify,
-	.suspend		= at803x_suspend,
-	.resume			= at803x_resume,
-	/* PHY_BASIC_FEATURES */
-	.config_intr		= at803x_config_intr,
-	.handle_interrupt	= at803x_handle_interrupt,
-	.cable_test_start	= at803x_cable_test_start,
-	.cable_test_get_status	= at8032_cable_test_get_status,
-}, {
-	/* ATHEROS AR9331 */
-	PHY_ID_MATCH_EXACT(ATH9331_PHY_ID),
-	.name			= "Qualcomm Atheros AR9331 built-in PHY",
-	.probe			= at803x_probe,
-	.suspend		= at803x_suspend,
-	.resume			= at803x_resume,
-	.flags			= PHY_POLL_CABLE_TEST,
-	/* PHY_BASIC_FEATURES */
-	.config_intr		= at803x_config_intr,
-	.handle_interrupt	= at803x_handle_interrupt,
-	.cable_test_start	= at803x_cable_test_start,
-	.cable_test_get_status	= at8032_cable_test_get_status,
-	.read_status		= at803x_read_status,
-	.soft_reset		= genphy_soft_reset,
-	.config_aneg		= at803x_config_aneg,
-}, {
-	/* Qualcomm Atheros QCA9561 */
-	PHY_ID_MATCH_EXACT(QCA9561_PHY_ID),
-	.name			= "Qualcomm Atheros QCA9561 built-in PHY",
-	.probe			= at803x_probe,
-	.suspend		= at803x_suspend,
-	.resume			= at803x_resume,
-	.flags			= PHY_POLL_CABLE_TEST,
-	/* PHY_BASIC_FEATURES */
-	.config_intr		= at803x_config_intr,
-	.handle_interrupt	= at803x_handle_interrupt,
-	.cable_test_start	= at803x_cable_test_start,
-	.cable_test_get_status	= at8032_cable_test_get_status,
-	.read_status		= at803x_read_status,
-	.soft_reset		= genphy_soft_reset,
-	.config_aneg		= at803x_config_aneg,
-}, {
-	/* QCA8337 */
-	.phy_id			= QCA8337_PHY_ID,
-	.phy_id_mask		= QCA8K_PHY_ID_MASK,
-	.name			= "Qualcomm Atheros 8337 internal PHY",
-	/* PHY_GBIT_FEATURES */
-	.probe			= at803x_probe,
-	.flags			= PHY_IS_INTERNAL,
-	.config_init		= qca83xx_config_init,
-	.soft_reset		= genphy_soft_reset,
-	.get_sset_count		= qca83xx_get_sset_count,
-	.get_strings		= qca83xx_get_strings,
-	.get_stats		= qca83xx_get_stats,
-	.suspend		= qca8337_suspend,
-	.resume			= qca83xx_resume,
-}, {
-	/* QCA8327-A from switch QCA8327-AL1A */
-	.phy_id			= QCA8327_A_PHY_ID,
-	.phy_id_mask		= QCA8K_PHY_ID_MASK,
-	.name			= "Qualcomm Atheros 8327-A internal PHY",
-	/* PHY_GBIT_FEATURES */
-	.link_change_notify	= qca83xx_link_change_notify,
-	.probe			= at803x_probe,
-	.flags			= PHY_IS_INTERNAL,
-	.config_init		= qca8327_config_init,
-	.soft_reset		= genphy_soft_reset,
-	.get_sset_count		= qca83xx_get_sset_count,
-	.get_strings		= qca83xx_get_strings,
-	.get_stats		= qca83xx_get_stats,
-	.suspend		= qca8327_suspend,
-	.resume			= qca83xx_resume,
-}, {
-	/* QCA8327-B from switch QCA8327-BL1A */
-	.phy_id			= QCA8327_B_PHY_ID,
-	.phy_id_mask		= QCA8K_PHY_ID_MASK,
-	.name			= "Qualcomm Atheros 8327-B internal PHY",
-	/* PHY_GBIT_FEATURES */
-	.link_change_notify	= qca83xx_link_change_notify,
-	.probe			= at803x_probe,
-	.flags			= PHY_IS_INTERNAL,
-	.config_init		= qca8327_config_init,
-	.soft_reset		= genphy_soft_reset,
-	.get_sset_count		= qca83xx_get_sset_count,
-	.get_strings		= qca83xx_get_strings,
-	.get_stats		= qca83xx_get_stats,
-	.suspend		= qca8327_suspend,
-	.resume			= qca83xx_resume,
-}, {
-	/* Qualcomm QCA8081 */
-	PHY_ID_MATCH_EXACT(QCA8081_PHY_ID),
-	.name			= "Qualcomm QCA8081",
-	.flags			= PHY_POLL_CABLE_TEST,
-	.probe			= at803x_probe,
-	.config_intr		= at803x_config_intr,
-	.handle_interrupt	= at803x_handle_interrupt,
-	.get_tunable		= at803x_get_tunable,
-	.set_tunable		= at803x_set_tunable,
-	.set_wol		= at803x_set_wol,
-	.get_wol		= at803x_get_wol,
-	.get_features		= qca808x_get_features,
-	.config_aneg		= qca808x_config_aneg,
-	.suspend		= genphy_suspend,
-	.resume			= genphy_resume,
-	.read_status		= qca808x_read_status,
-	.config_init		= qca808x_config_init,
-	.soft_reset		= qca808x_soft_reset,
-	.cable_test_start	= qca808x_cable_test_start,
-	.cable_test_get_status	= qca808x_cable_test_get_status,
-	.link_change_notify	= qca808x_link_change_notify,
-	.led_brightness_set	= qca808x_led_brightness_set,
-	.led_blink_set		= qca808x_led_blink_set,
-	.led_hw_is_supported	= qca808x_led_hw_is_supported,
-	.led_hw_control_set	= qca808x_led_hw_control_set,
-	.led_hw_control_get	= qca808x_led_hw_control_get,
-	.led_polarity_set	= qca808x_led_polarity_set,
-}, };
-
-module_phy_driver(at803x_driver);
-
-static struct mdio_device_id __maybe_unused atheros_tbl[] = {
-	{ ATH8030_PHY_ID, AT8030_PHY_ID_MASK },
-	{ PHY_ID_MATCH_EXACT(ATH8031_PHY_ID) },
-	{ PHY_ID_MATCH_EXACT(ATH8032_PHY_ID) },
-	{ PHY_ID_MATCH_EXACT(ATH8035_PHY_ID) },
-	{ PHY_ID_MATCH_EXACT(ATH9331_PHY_ID) },
-	{ PHY_ID_MATCH_EXACT(QCA8337_PHY_ID) },
-	{ PHY_ID_MATCH_EXACT(QCA8327_A_PHY_ID) },
-	{ PHY_ID_MATCH_EXACT(QCA8327_B_PHY_ID) },
-	{ PHY_ID_MATCH_EXACT(QCA9561_PHY_ID) },
-	{ PHY_ID_MATCH_EXACT(QCA8081_PHY_ID) },
-	{ }
-};
-
-MODULE_DEVICE_TABLE(mdio, atheros_tbl);
--- /dev/null
+++ b/drivers/net/phy/qcom/at803x.c
@@ -0,0 +1,2759 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * drivers/net/phy/at803x.c
+ *
+ * Driver for Qualcomm Atheros AR803x PHY
+ *
+ * Author: Matus Ujhelyi <[email protected]>
+ */
+
+#include <linux/phy.h>
+#include <linux/module.h>
+#include <linux/string.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/ethtool_netlink.h>
+#include <linux/bitfield.h>
+#include <linux/regulator/of_regulator.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/consumer.h>
+#include <linux/of.h>
+#include <linux/phylink.h>
+#include <linux/sfp.h>
+#include <dt-bindings/net/qca-ar803x.h>
+
+#define AT803X_SPECIFIC_FUNCTION_CONTROL	0x10
+#define AT803X_SFC_ASSERT_CRS			BIT(11)
+#define AT803X_SFC_FORCE_LINK			BIT(10)
+#define AT803X_SFC_MDI_CROSSOVER_MODE_M		GENMASK(6, 5)
+#define AT803X_SFC_AUTOMATIC_CROSSOVER		0x3
+#define AT803X_SFC_MANUAL_MDIX			0x1
+#define AT803X_SFC_MANUAL_MDI			0x0
+#define AT803X_SFC_SQE_TEST			BIT(2)
+#define AT803X_SFC_POLARITY_REVERSAL		BIT(1)
+#define AT803X_SFC_DISABLE_JABBER		BIT(0)
+
+#define AT803X_SPECIFIC_STATUS			0x11
+#define AT803X_SS_SPEED_MASK			GENMASK(15, 14)
+#define AT803X_SS_SPEED_1000			2
+#define AT803X_SS_SPEED_100			1
+#define AT803X_SS_SPEED_10			0
+#define AT803X_SS_DUPLEX			BIT(13)
+#define AT803X_SS_SPEED_DUPLEX_RESOLVED		BIT(11)
+#define AT803X_SS_MDIX				BIT(6)
+
+#define QCA808X_SS_SPEED_MASK			GENMASK(9, 7)
+#define QCA808X_SS_SPEED_2500			4
+
+#define AT803X_INTR_ENABLE			0x12
+#define AT803X_INTR_ENABLE_AUTONEG_ERR		BIT(15)
+#define AT803X_INTR_ENABLE_SPEED_CHANGED	BIT(14)
+#define AT803X_INTR_ENABLE_DUPLEX_CHANGED	BIT(13)
+#define AT803X_INTR_ENABLE_PAGE_RECEIVED	BIT(12)
+#define AT803X_INTR_ENABLE_LINK_FAIL		BIT(11)
+#define AT803X_INTR_ENABLE_LINK_SUCCESS		BIT(10)
+#define AT803X_INTR_ENABLE_LINK_FAIL_BX		BIT(8)
+#define AT803X_INTR_ENABLE_LINK_SUCCESS_BX	BIT(7)
+#define AT803X_INTR_ENABLE_WIRESPEED_DOWNGRADE	BIT(5)
+#define AT803X_INTR_ENABLE_POLARITY_CHANGED	BIT(1)
+#define AT803X_INTR_ENABLE_WOL			BIT(0)
+
+#define AT803X_INTR_STATUS			0x13
+
+#define AT803X_SMART_SPEED			0x14
+#define AT803X_SMART_SPEED_ENABLE		BIT(5)
+#define AT803X_SMART_SPEED_RETRY_LIMIT_MASK	GENMASK(4, 2)
+#define AT803X_SMART_SPEED_BYPASS_TIMER		BIT(1)
+#define AT803X_CDT				0x16
+#define AT803X_CDT_MDI_PAIR_MASK		GENMASK(9, 8)
+#define AT803X_CDT_ENABLE_TEST			BIT(0)
+#define AT803X_CDT_STATUS			0x1c
+#define AT803X_CDT_STATUS_STAT_NORMAL		0
+#define AT803X_CDT_STATUS_STAT_SHORT		1
+#define AT803X_CDT_STATUS_STAT_OPEN		2
+#define AT803X_CDT_STATUS_STAT_FAIL		3
+#define AT803X_CDT_STATUS_STAT_MASK		GENMASK(9, 8)
+#define AT803X_CDT_STATUS_DELTA_TIME_MASK	GENMASK(7, 0)
+#define AT803X_LED_CONTROL			0x18
+
+#define AT803X_PHY_MMD3_WOL_CTRL		0x8012
+#define AT803X_WOL_EN				BIT(5)
+#define AT803X_LOC_MAC_ADDR_0_15_OFFSET		0x804C
+#define AT803X_LOC_MAC_ADDR_16_31_OFFSET	0x804B
+#define AT803X_LOC_MAC_ADDR_32_47_OFFSET	0x804A
+#define AT803X_REG_CHIP_CONFIG			0x1f
+#define AT803X_BT_BX_REG_SEL			0x8000
+
+#define AT803X_DEBUG_ADDR			0x1D
+#define AT803X_DEBUG_DATA			0x1E
+
+#define AT803X_MODE_CFG_MASK			0x0F
+#define AT803X_MODE_CFG_BASET_RGMII		0x00
+#define AT803X_MODE_CFG_BASET_SGMII		0x01
+#define AT803X_MODE_CFG_BX1000_RGMII_50OHM	0x02
+#define AT803X_MODE_CFG_BX1000_RGMII_75OHM	0x03
+#define AT803X_MODE_CFG_BX1000_CONV_50OHM	0x04
+#define AT803X_MODE_CFG_BX1000_CONV_75OHM	0x05
+#define AT803X_MODE_CFG_FX100_RGMII_50OHM	0x06
+#define AT803X_MODE_CFG_FX100_CONV_50OHM	0x07
+#define AT803X_MODE_CFG_RGMII_AUTO_MDET		0x0B
+#define AT803X_MODE_CFG_FX100_RGMII_75OHM	0x0E
+#define AT803X_MODE_CFG_FX100_CONV_75OHM	0x0F
+
+#define AT803X_PSSR				0x11	/*PHY-Specific Status Register*/
+#define AT803X_PSSR_MR_AN_COMPLETE		0x0200
+
+#define AT803X_DEBUG_ANALOG_TEST_CTRL		0x00
+#define QCA8327_DEBUG_MANU_CTRL_EN		BIT(2)
+#define QCA8337_DEBUG_MANU_CTRL_EN		GENMASK(3, 2)
+#define AT803X_DEBUG_RX_CLK_DLY_EN		BIT(15)
+
+#define AT803X_DEBUG_SYSTEM_CTRL_MODE		0x05
+#define AT803X_DEBUG_TX_CLK_DLY_EN		BIT(8)
+
+#define AT803X_DEBUG_REG_HIB_CTRL		0x0b
+#define   AT803X_DEBUG_HIB_CTRL_SEL_RST_80U	BIT(10)
+#define   AT803X_DEBUG_HIB_CTRL_EN_ANY_CHANGE	BIT(13)
+#define   AT803X_DEBUG_HIB_CTRL_PS_HIB_EN	BIT(15)
+
+#define AT803X_DEBUG_REG_3C			0x3C
+
+#define AT803X_DEBUG_REG_GREEN			0x3D
+#define   AT803X_DEBUG_GATE_CLK_IN1000		BIT(6)
+
+#define AT803X_DEBUG_REG_1F			0x1F
+#define AT803X_DEBUG_PLL_ON			BIT(2)
+#define AT803X_DEBUG_RGMII_1V8			BIT(3)
+
+#define MDIO_AZ_DEBUG				0x800D
+
+/* AT803x supports either the XTAL input pad, an internal PLL or the
+ * DSP as clock reference for the clock output pad. The XTAL reference
+ * is only used for 25 MHz output, all other frequencies need the PLL.
+ * The DSP as a clock reference is used in synchronous ethernet
+ * applications.
+ *
+ * By default the PLL is only enabled if there is a link. Otherwise
+ * the PHY will go into low power state and disabled the PLL. You can
+ * set the PLL_ON bit (see debug register 0x1f) to keep the PLL always
+ * enabled.
+ */
+#define AT803X_MMD7_CLK25M			0x8016
+#define AT803X_CLK_OUT_MASK			GENMASK(4, 2)
+#define AT803X_CLK_OUT_25MHZ_XTAL		0
+#define AT803X_CLK_OUT_25MHZ_DSP		1
+#define AT803X_CLK_OUT_50MHZ_PLL		2
+#define AT803X_CLK_OUT_50MHZ_DSP		3
+#define AT803X_CLK_OUT_62_5MHZ_PLL		4
+#define AT803X_CLK_OUT_62_5MHZ_DSP		5
+#define AT803X_CLK_OUT_125MHZ_PLL		6
+#define AT803X_CLK_OUT_125MHZ_DSP		7
+
+/* The AR8035 has another mask which is compatible with the AR8031/AR8033 mask
+ * but doesn't support choosing between XTAL/PLL and DSP.
+ */
+#define AT8035_CLK_OUT_MASK			GENMASK(4, 3)
+
+#define AT803X_CLK_OUT_STRENGTH_MASK		GENMASK(8, 7)
+#define AT803X_CLK_OUT_STRENGTH_FULL		0
+#define AT803X_CLK_OUT_STRENGTH_HALF		1
+#define AT803X_CLK_OUT_STRENGTH_QUARTER		2
+
+#define AT803X_DEFAULT_DOWNSHIFT		5
+#define AT803X_MIN_DOWNSHIFT			2
+#define AT803X_MAX_DOWNSHIFT			9
+
+#define AT803X_MMD3_SMARTEEE_CTL1		0x805b
+#define AT803X_MMD3_SMARTEEE_CTL2		0x805c
+#define AT803X_MMD3_SMARTEEE_CTL3		0x805d
+#define AT803X_MMD3_SMARTEEE_CTL3_LPI_EN	BIT(8)
+
+#define ATH9331_PHY_ID				0x004dd041
+#define ATH8030_PHY_ID				0x004dd076
+#define ATH8031_PHY_ID				0x004dd074
+#define ATH8032_PHY_ID				0x004dd023
+#define ATH8035_PHY_ID				0x004dd072
+#define AT8030_PHY_ID_MASK			0xffffffef
+
+#define QCA8081_PHY_ID				0x004dd101
+
+#define QCA8327_A_PHY_ID			0x004dd033
+#define QCA8327_B_PHY_ID			0x004dd034
+#define QCA8337_PHY_ID				0x004dd036
+#define QCA9561_PHY_ID				0x004dd042
+#define QCA8K_PHY_ID_MASK			0xffffffff
+
+#define QCA8K_DEVFLAGS_REVISION_MASK		GENMASK(2, 0)
+
+#define AT803X_PAGE_FIBER			0
+#define AT803X_PAGE_COPPER			1
+
+/* don't turn off internal PLL */
+#define AT803X_KEEP_PLL_ENABLED			BIT(0)
+#define AT803X_DISABLE_SMARTEEE			BIT(1)
+
+/* disable hibernation mode */
+#define AT803X_DISABLE_HIBERNATION_MODE		BIT(2)
+
+/* ADC threshold */
+#define QCA808X_PHY_DEBUG_ADC_THRESHOLD		0x2c80
+#define QCA808X_ADC_THRESHOLD_MASK		GENMASK(7, 0)
+#define QCA808X_ADC_THRESHOLD_80MV		0
+#define QCA808X_ADC_THRESHOLD_100MV		0xf0
+#define QCA808X_ADC_THRESHOLD_200MV		0x0f
+#define QCA808X_ADC_THRESHOLD_300MV		0xff
+
+/* CLD control */
+#define QCA808X_PHY_MMD3_ADDR_CLD_CTRL7		0x8007
+#define QCA808X_8023AZ_AFE_CTRL_MASK		GENMASK(8, 4)
+#define QCA808X_8023AZ_AFE_EN			0x90
+
+/* AZ control */
+#define QCA808X_PHY_MMD3_AZ_TRAINING_CTRL	0x8008
+#define QCA808X_MMD3_AZ_TRAINING_VAL		0x1c32
+
+#define QCA808X_PHY_MMD1_MSE_THRESHOLD_20DB	0x8014
+#define QCA808X_MSE_THRESHOLD_20DB_VALUE	0x529
+
+#define QCA808X_PHY_MMD1_MSE_THRESHOLD_17DB	0x800E
+#define QCA808X_MSE_THRESHOLD_17DB_VALUE	0x341
+
+#define QCA808X_PHY_MMD1_MSE_THRESHOLD_27DB	0x801E
+#define QCA808X_MSE_THRESHOLD_27DB_VALUE	0x419
+
+#define QCA808X_PHY_MMD1_MSE_THRESHOLD_28DB	0x8020
+#define QCA808X_MSE_THRESHOLD_28DB_VALUE	0x341
+
+#define QCA808X_PHY_MMD7_TOP_OPTION1		0x901c
+#define QCA808X_TOP_OPTION1_DATA		0x0
+
+#define QCA808X_PHY_MMD3_DEBUG_1		0xa100
+#define QCA808X_MMD3_DEBUG_1_VALUE		0x9203
+#define QCA808X_PHY_MMD3_DEBUG_2		0xa101
+#define QCA808X_MMD3_DEBUG_2_VALUE		0x48ad
+#define QCA808X_PHY_MMD3_DEBUG_3		0xa103
+#define QCA808X_MMD3_DEBUG_3_VALUE		0x1698
+#define QCA808X_PHY_MMD3_DEBUG_4		0xa105
+#define QCA808X_MMD3_DEBUG_4_VALUE		0x8001
+#define QCA808X_PHY_MMD3_DEBUG_5		0xa106
+#define QCA808X_MMD3_DEBUG_5_VALUE		0x1111
+#define QCA808X_PHY_MMD3_DEBUG_6		0xa011
+#define QCA808X_MMD3_DEBUG_6_VALUE		0x5f85
+
+/* master/slave seed config */
+#define QCA808X_PHY_DEBUG_LOCAL_SEED		9
+#define QCA808X_MASTER_SLAVE_SEED_ENABLE	BIT(1)
+#define QCA808X_MASTER_SLAVE_SEED_CFG		GENMASK(12, 2)
+#define QCA808X_MASTER_SLAVE_SEED_RANGE		0x32
+
+/* Hibernation yields lower power consumpiton in contrast with normal operation mode.
+ * when the copper cable is unplugged, the PHY enters into hibernation mode in about 10s.
+ */
+#define QCA808X_DBG_AN_TEST			0xb
+#define QCA808X_HIBERNATION_EN			BIT(15)
+
+#define QCA808X_CDT_ENABLE_TEST			BIT(15)
+#define QCA808X_CDT_INTER_CHECK_DIS		BIT(13)
+#define QCA808X_CDT_STATUS			BIT(11)
+#define QCA808X_CDT_LENGTH_UNIT			BIT(10)
+
+#define QCA808X_MMD3_CDT_STATUS			0x8064
+#define QCA808X_MMD3_CDT_DIAG_PAIR_A		0x8065
+#define QCA808X_MMD3_CDT_DIAG_PAIR_B		0x8066
+#define QCA808X_MMD3_CDT_DIAG_PAIR_C		0x8067
+#define QCA808X_MMD3_CDT_DIAG_PAIR_D		0x8068
+#define QCA808X_CDT_DIAG_LENGTH_SAME_SHORT	GENMASK(15, 8)
+#define QCA808X_CDT_DIAG_LENGTH_CROSS_SHORT	GENMASK(7, 0)
+
+#define QCA808X_CDT_CODE_PAIR_A			GENMASK(15, 12)
+#define QCA808X_CDT_CODE_PAIR_B			GENMASK(11, 8)
+#define QCA808X_CDT_CODE_PAIR_C			GENMASK(7, 4)
+#define QCA808X_CDT_CODE_PAIR_D			GENMASK(3, 0)
+
+#define QCA808X_CDT_STATUS_STAT_TYPE		GENMASK(1, 0)
+#define QCA808X_CDT_STATUS_STAT_FAIL		FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_TYPE, 0)
+#define QCA808X_CDT_STATUS_STAT_NORMAL		FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_TYPE, 1)
+#define QCA808X_CDT_STATUS_STAT_SAME_OPEN	FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_TYPE, 2)
+#define QCA808X_CDT_STATUS_STAT_SAME_SHORT	FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_TYPE, 3)
+
+#define QCA808X_CDT_STATUS_STAT_MDI		GENMASK(3, 2)
+#define QCA808X_CDT_STATUS_STAT_MDI1		FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_MDI, 1)
+#define QCA808X_CDT_STATUS_STAT_MDI2		FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_MDI, 2)
+#define QCA808X_CDT_STATUS_STAT_MDI3		FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_MDI, 3)
+
+/* NORMAL are MDI with type set to 0 */
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_NORMAL	QCA808X_CDT_STATUS_STAT_MDI1
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_OPEN		(QCA808X_CDT_STATUS_STAT_SAME_OPEN |\
+									 QCA808X_CDT_STATUS_STAT_MDI1)
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_SHORT	(QCA808X_CDT_STATUS_STAT_SAME_SHORT |\
+									 QCA808X_CDT_STATUS_STAT_MDI1)
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_NORMAL	QCA808X_CDT_STATUS_STAT_MDI2
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_OPEN		(QCA808X_CDT_STATUS_STAT_SAME_OPEN |\
+									 QCA808X_CDT_STATUS_STAT_MDI2)
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_SHORT	(QCA808X_CDT_STATUS_STAT_SAME_SHORT |\
+									 QCA808X_CDT_STATUS_STAT_MDI2)
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_NORMAL	QCA808X_CDT_STATUS_STAT_MDI3
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_OPEN		(QCA808X_CDT_STATUS_STAT_SAME_OPEN |\
+									 QCA808X_CDT_STATUS_STAT_MDI3)
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_SHORT	(QCA808X_CDT_STATUS_STAT_SAME_SHORT |\
+									 QCA808X_CDT_STATUS_STAT_MDI3)
+
+/* Added for reference of existence but should be handled by wait_for_completion already */
+#define QCA808X_CDT_STATUS_STAT_BUSY		(BIT(1) | BIT(3))
+
+#define QCA808X_MMD7_LED_GLOBAL			0x8073
+#define QCA808X_LED_BLINK_1			GENMASK(11, 6)
+#define QCA808X_LED_BLINK_2			GENMASK(5, 0)
+/* Values are the same for both BLINK_1 and BLINK_2 */
+#define QCA808X_LED_BLINK_FREQ_MASK		GENMASK(5, 3)
+#define QCA808X_LED_BLINK_FREQ_2HZ		FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x0)
+#define QCA808X_LED_BLINK_FREQ_4HZ		FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x1)
+#define QCA808X_LED_BLINK_FREQ_8HZ		FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x2)
+#define QCA808X_LED_BLINK_FREQ_16HZ		FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x3)
+#define QCA808X_LED_BLINK_FREQ_32HZ		FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x4)
+#define QCA808X_LED_BLINK_FREQ_64HZ		FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x5)
+#define QCA808X_LED_BLINK_FREQ_128HZ		FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x6)
+#define QCA808X_LED_BLINK_FREQ_256HZ		FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x7)
+#define QCA808X_LED_BLINK_DUTY_MASK		GENMASK(2, 0)
+#define QCA808X_LED_BLINK_DUTY_50_50		FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x0)
+#define QCA808X_LED_BLINK_DUTY_75_25		FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x1)
+#define QCA808X_LED_BLINK_DUTY_25_75		FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x2)
+#define QCA808X_LED_BLINK_DUTY_33_67		FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x3)
+#define QCA808X_LED_BLINK_DUTY_67_33		FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x4)
+#define QCA808X_LED_BLINK_DUTY_17_83		FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x5)
+#define QCA808X_LED_BLINK_DUTY_83_17		FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x6)
+#define QCA808X_LED_BLINK_DUTY_8_92		FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x7)
+
+#define QCA808X_MMD7_LED2_CTRL			0x8074
+#define QCA808X_MMD7_LED2_FORCE_CTRL		0x8075
+#define QCA808X_MMD7_LED1_CTRL			0x8076
+#define QCA808X_MMD7_LED1_FORCE_CTRL		0x8077
+#define QCA808X_MMD7_LED0_CTRL			0x8078
+#define QCA808X_MMD7_LED_CTRL(x)		(0x8078 - ((x) * 2))
+
+/* LED hw control pattern is the same for every LED */
+#define QCA808X_LED_PATTERN_MASK		GENMASK(15, 0)
+#define QCA808X_LED_SPEED2500_ON		BIT(15)
+#define QCA808X_LED_SPEED2500_BLINK		BIT(14)
+/* Follow blink trigger even if duplex or speed condition doesn't match */
+#define QCA808X_LED_BLINK_CHECK_BYPASS		BIT(13)
+#define QCA808X_LED_FULL_DUPLEX_ON		BIT(12)
+#define QCA808X_LED_HALF_DUPLEX_ON		BIT(11)
+#define QCA808X_LED_TX_BLINK			BIT(10)
+#define QCA808X_LED_RX_BLINK			BIT(9)
+#define QCA808X_LED_TX_ON_10MS			BIT(8)
+#define QCA808X_LED_RX_ON_10MS			BIT(7)
+#define QCA808X_LED_SPEED1000_ON		BIT(6)
+#define QCA808X_LED_SPEED100_ON			BIT(5)
+#define QCA808X_LED_SPEED10_ON			BIT(4)
+#define QCA808X_LED_COLLISION_BLINK		BIT(3)
+#define QCA808X_LED_SPEED1000_BLINK		BIT(2)
+#define QCA808X_LED_SPEED100_BLINK		BIT(1)
+#define QCA808X_LED_SPEED10_BLINK		BIT(0)
+
+#define QCA808X_MMD7_LED0_FORCE_CTRL		0x8079
+#define QCA808X_MMD7_LED_FORCE_CTRL(x)		(0x8079 - ((x) * 2))
+
+/* LED force ctrl is the same for every LED
+ * No documentation exist for this, not even internal one
+ * with NDA as QCOM gives only info about configuring
+ * hw control pattern rules and doesn't indicate any way
+ * to force the LED to specific mode.
+ * These define comes from reverse and testing and maybe
+ * lack of some info or some info are not entirely correct.
+ * For the basic LED control and hw control these finding
+ * are enough to support LED control in all the required APIs.
+ *
+ * On doing some comparison with implementation with qca807x,
+ * it was found that it's 1:1 equal to it and confirms all the
+ * reverse done. It was also found further specification with the
+ * force mode and the blink modes.
+ */
+#define QCA808X_LED_FORCE_EN			BIT(15)
+#define QCA808X_LED_FORCE_MODE_MASK		GENMASK(14, 13)
+#define QCA808X_LED_FORCE_BLINK_1		FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x3)
+#define QCA808X_LED_FORCE_BLINK_2		FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x2)
+#define QCA808X_LED_FORCE_ON			FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x1)
+#define QCA808X_LED_FORCE_OFF			FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x0)
+
+#define QCA808X_MMD7_LED_POLARITY_CTRL		0x901a
+/* QSDK sets by default 0x46 to this reg that sets BIT 6 for
+ * LED to active high. It's not clear what BIT 3 and BIT 4 does.
+ */
+#define QCA808X_LED_ACTIVE_HIGH			BIT(6)
+
+/* QCA808X 1G chip type */
+#define QCA808X_PHY_MMD7_CHIP_TYPE		0x901d
+#define QCA808X_PHY_CHIP_TYPE_1G		BIT(0)
+
+#define QCA8081_PHY_SERDES_MMD1_FIFO_CTRL	0x9072
+#define QCA8081_PHY_FIFO_RSTN			BIT(11)
+
+MODULE_DESCRIPTION("Qualcomm Atheros AR803x and QCA808X PHY driver");
+MODULE_AUTHOR("Matus Ujhelyi");
+MODULE_LICENSE("GPL");
+
+enum stat_access_type {
+	PHY,
+	MMD
+};
+
+struct at803x_hw_stat {
+	const char *string;
+	u8 reg;
+	u32 mask;
+	enum stat_access_type access_type;
+};
+
+static struct at803x_hw_stat qca83xx_hw_stats[] = {
+	{ "phy_idle_errors", 0xa, GENMASK(7, 0), PHY},
+	{ "phy_receive_errors", 0x15, GENMASK(15, 0), PHY},
+	{ "eee_wake_errors", 0x16, GENMASK(15, 0), MMD},
+};
+
+struct at803x_ss_mask {
+	u16 speed_mask;
+	u8 speed_shift;
+};
+
+struct at803x_priv {
+	int flags;
+	u16 clk_25m_reg;
+	u16 clk_25m_mask;
+	u8 smarteee_lpi_tw_1g;
+	u8 smarteee_lpi_tw_100m;
+	bool is_fiber;
+	bool is_1000basex;
+	struct regulator_dev *vddio_rdev;
+	struct regulator_dev *vddh_rdev;
+	u64 stats[ARRAY_SIZE(qca83xx_hw_stats)];
+	int led_polarity_mode;
+};
+
+struct at803x_context {
+	u16 bmcr;
+	u16 advertise;
+	u16 control1000;
+	u16 int_enable;
+	u16 smart_speed;
+	u16 led_control;
+};
+
+static int at803x_debug_reg_write(struct phy_device *phydev, u16 reg, u16 data)
+{
+	int ret;
+
+	ret = phy_write(phydev, AT803X_DEBUG_ADDR, reg);
+	if (ret < 0)
+		return ret;
+
+	return phy_write(phydev, AT803X_DEBUG_DATA, data);
+}
+
+static int at803x_debug_reg_read(struct phy_device *phydev, u16 reg)
+{
+	int ret;
+
+	ret = phy_write(phydev, AT803X_DEBUG_ADDR, reg);
+	if (ret < 0)
+		return ret;
+
+	return phy_read(phydev, AT803X_DEBUG_DATA);
+}
+
+static int at803x_debug_reg_mask(struct phy_device *phydev, u16 reg,
+				 u16 clear, u16 set)
+{
+	u16 val;
+	int ret;
+
+	ret = at803x_debug_reg_read(phydev, reg);
+	if (ret < 0)
+		return ret;
+
+	val = ret & 0xffff;
+	val &= ~clear;
+	val |= set;
+
+	return phy_write(phydev, AT803X_DEBUG_DATA, val);
+}
+
+static int at803x_write_page(struct phy_device *phydev, int page)
+{
+	int mask;
+	int set;
+
+	if (page == AT803X_PAGE_COPPER) {
+		set = AT803X_BT_BX_REG_SEL;
+		mask = 0;
+	} else {
+		set = 0;
+		mask = AT803X_BT_BX_REG_SEL;
+	}
+
+	return __phy_modify(phydev, AT803X_REG_CHIP_CONFIG, mask, set);
+}
+
+static int at803x_read_page(struct phy_device *phydev)
+{
+	int ccr = __phy_read(phydev, AT803X_REG_CHIP_CONFIG);
+
+	if (ccr < 0)
+		return ccr;
+
+	if (ccr & AT803X_BT_BX_REG_SEL)
+		return AT803X_PAGE_COPPER;
+
+	return AT803X_PAGE_FIBER;
+}
+
+static int at803x_enable_rx_delay(struct phy_device *phydev)
+{
+	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL, 0,
+				     AT803X_DEBUG_RX_CLK_DLY_EN);
+}
+
+static int at803x_enable_tx_delay(struct phy_device *phydev)
+{
+	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_SYSTEM_CTRL_MODE, 0,
+				     AT803X_DEBUG_TX_CLK_DLY_EN);
+}
+
+static int at803x_disable_rx_delay(struct phy_device *phydev)
+{
+	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL,
+				     AT803X_DEBUG_RX_CLK_DLY_EN, 0);
+}
+
+static int at803x_disable_tx_delay(struct phy_device *phydev)
+{
+	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_SYSTEM_CTRL_MODE,
+				     AT803X_DEBUG_TX_CLK_DLY_EN, 0);
+}
+
+/* save relevant PHY registers to private copy */
+static void at803x_context_save(struct phy_device *phydev,
+				struct at803x_context *context)
+{
+	context->bmcr = phy_read(phydev, MII_BMCR);
+	context->advertise = phy_read(phydev, MII_ADVERTISE);
+	context->control1000 = phy_read(phydev, MII_CTRL1000);
+	context->int_enable = phy_read(phydev, AT803X_INTR_ENABLE);
+	context->smart_speed = phy_read(phydev, AT803X_SMART_SPEED);
+	context->led_control = phy_read(phydev, AT803X_LED_CONTROL);
+}
+
+/* restore relevant PHY registers from private copy */
+static void at803x_context_restore(struct phy_device *phydev,
+				   const struct at803x_context *context)
+{
+	phy_write(phydev, MII_BMCR, context->bmcr);
+	phy_write(phydev, MII_ADVERTISE, context->advertise);
+	phy_write(phydev, MII_CTRL1000, context->control1000);
+	phy_write(phydev, AT803X_INTR_ENABLE, context->int_enable);
+	phy_write(phydev, AT803X_SMART_SPEED, context->smart_speed);
+	phy_write(phydev, AT803X_LED_CONTROL, context->led_control);
+}
+
+static int at803x_set_wol(struct phy_device *phydev,
+			  struct ethtool_wolinfo *wol)
+{
+	int ret, irq_enabled;
+
+	if (wol->wolopts & WAKE_MAGIC) {
+		struct net_device *ndev = phydev->attached_dev;
+		const u8 *mac;
+		unsigned int i;
+		static const unsigned int offsets[] = {
+			AT803X_LOC_MAC_ADDR_32_47_OFFSET,
+			AT803X_LOC_MAC_ADDR_16_31_OFFSET,
+			AT803X_LOC_MAC_ADDR_0_15_OFFSET,
+		};
+
+		if (!ndev)
+			return -ENODEV;
+
+		mac = (const u8 *)ndev->dev_addr;
+
+		if (!is_valid_ether_addr(mac))
+			return -EINVAL;
+
+		for (i = 0; i < 3; i++)
+			phy_write_mmd(phydev, MDIO_MMD_PCS, offsets[i],
+				      mac[(i * 2) + 1] | (mac[(i * 2)] << 8));
+
+		/* Enable WOL interrupt */
+		ret = phy_modify(phydev, AT803X_INTR_ENABLE, 0, AT803X_INTR_ENABLE_WOL);
+		if (ret)
+			return ret;
+	} else {
+		/* Disable WOL interrupt */
+		ret = phy_modify(phydev, AT803X_INTR_ENABLE, AT803X_INTR_ENABLE_WOL, 0);
+		if (ret)
+			return ret;
+	}
+
+	/* Clear WOL status */
+	ret = phy_read(phydev, AT803X_INTR_STATUS);
+	if (ret < 0)
+		return ret;
+
+	/* Check if there are other interrupts except for WOL triggered when PHY is
+	 * in interrupt mode, only the interrupts enabled by AT803X_INTR_ENABLE can
+	 * be passed up to the interrupt PIN.
+	 */
+	irq_enabled = phy_read(phydev, AT803X_INTR_ENABLE);
+	if (irq_enabled < 0)
+		return irq_enabled;
+
+	irq_enabled &= ~AT803X_INTR_ENABLE_WOL;
+	if (ret & irq_enabled && !phy_polling_mode(phydev))
+		phy_trigger_machine(phydev);
+
+	return 0;
+}
+
+static void at803x_get_wol(struct phy_device *phydev,
+			   struct ethtool_wolinfo *wol)
+{
+	int value;
+
+	wol->supported = WAKE_MAGIC;
+	wol->wolopts = 0;
+
+	value = phy_read(phydev, AT803X_INTR_ENABLE);
+	if (value < 0)
+		return;
+
+	if (value & AT803X_INTR_ENABLE_WOL)
+		wol->wolopts |= WAKE_MAGIC;
+}
+
+static int qca83xx_get_sset_count(struct phy_device *phydev)
+{
+	return ARRAY_SIZE(qca83xx_hw_stats);
+}
+
+static void qca83xx_get_strings(struct phy_device *phydev, u8 *data)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(qca83xx_hw_stats); i++) {
+		strscpy(data + i * ETH_GSTRING_LEN,
+			qca83xx_hw_stats[i].string, ETH_GSTRING_LEN);
+	}
+}
+
+static u64 qca83xx_get_stat(struct phy_device *phydev, int i)
+{
+	struct at803x_hw_stat stat = qca83xx_hw_stats[i];
+	struct at803x_priv *priv = phydev->priv;
+	int val;
+	u64 ret;
+
+	if (stat.access_type == MMD)
+		val = phy_read_mmd(phydev, MDIO_MMD_PCS, stat.reg);
+	else
+		val = phy_read(phydev, stat.reg);
+
+	if (val < 0) {
+		ret = U64_MAX;
+	} else {
+		val = val & stat.mask;
+		priv->stats[i] += val;
+		ret = priv->stats[i];
+	}
+
+	return ret;
+}
+
+static void qca83xx_get_stats(struct phy_device *phydev,
+			      struct ethtool_stats *stats, u64 *data)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(qca83xx_hw_stats); i++)
+		data[i] = qca83xx_get_stat(phydev, i);
+}
+
+static int at803x_suspend(struct phy_device *phydev)
+{
+	int value;
+	int wol_enabled;
+
+	value = phy_read(phydev, AT803X_INTR_ENABLE);
+	wol_enabled = value & AT803X_INTR_ENABLE_WOL;
+
+	if (wol_enabled)
+		value = BMCR_ISOLATE;
+	else
+		value = BMCR_PDOWN;
+
+	phy_modify(phydev, MII_BMCR, 0, value);
+
+	return 0;
+}
+
+static int at803x_resume(struct phy_device *phydev)
+{
+	return phy_modify(phydev, MII_BMCR, BMCR_PDOWN | BMCR_ISOLATE, 0);
+}
+
+static int at803x_parse_dt(struct phy_device *phydev)
+{
+	struct device_node *node = phydev->mdio.dev.of_node;
+	struct at803x_priv *priv = phydev->priv;
+	u32 freq, strength, tw;
+	unsigned int sel;
+	int ret;
+
+	if (!IS_ENABLED(CONFIG_OF_MDIO))
+		return 0;
+
+	if (of_property_read_bool(node, "qca,disable-smarteee"))
+		priv->flags |= AT803X_DISABLE_SMARTEEE;
+
+	if (of_property_read_bool(node, "qca,disable-hibernation-mode"))
+		priv->flags |= AT803X_DISABLE_HIBERNATION_MODE;
+
+	if (!of_property_read_u32(node, "qca,smarteee-tw-us-1g", &tw)) {
+		if (!tw || tw > 255) {
+			phydev_err(phydev, "invalid qca,smarteee-tw-us-1g\n");
+			return -EINVAL;
+		}
+		priv->smarteee_lpi_tw_1g = tw;
+	}
+
+	if (!of_property_read_u32(node, "qca,smarteee-tw-us-100m", &tw)) {
+		if (!tw || tw > 255) {
+			phydev_err(phydev, "invalid qca,smarteee-tw-us-100m\n");
+			return -EINVAL;
+		}
+		priv->smarteee_lpi_tw_100m = tw;
+	}
+
+	ret = of_property_read_u32(node, "qca,clk-out-frequency", &freq);
+	if (!ret) {
+		switch (freq) {
+		case 25000000:
+			sel = AT803X_CLK_OUT_25MHZ_XTAL;
+			break;
+		case 50000000:
+			sel = AT803X_CLK_OUT_50MHZ_PLL;
+			break;
+		case 62500000:
+			sel = AT803X_CLK_OUT_62_5MHZ_PLL;
+			break;
+		case 125000000:
+			sel = AT803X_CLK_OUT_125MHZ_PLL;
+			break;
+		default:
+			phydev_err(phydev, "invalid qca,clk-out-frequency\n");
+			return -EINVAL;
+		}
+
+		priv->clk_25m_reg |= FIELD_PREP(AT803X_CLK_OUT_MASK, sel);
+		priv->clk_25m_mask |= AT803X_CLK_OUT_MASK;
+	}
+
+	ret = of_property_read_u32(node, "qca,clk-out-strength", &strength);
+	if (!ret) {
+		priv->clk_25m_mask |= AT803X_CLK_OUT_STRENGTH_MASK;
+		switch (strength) {
+		case AR803X_STRENGTH_FULL:
+			priv->clk_25m_reg |= AT803X_CLK_OUT_STRENGTH_FULL;
+			break;
+		case AR803X_STRENGTH_HALF:
+			priv->clk_25m_reg |= AT803X_CLK_OUT_STRENGTH_HALF;
+			break;
+		case AR803X_STRENGTH_QUARTER:
+			priv->clk_25m_reg |= AT803X_CLK_OUT_STRENGTH_QUARTER;
+			break;
+		default:
+			phydev_err(phydev, "invalid qca,clk-out-strength\n");
+			return -EINVAL;
+		}
+	}
+
+	return 0;
+}
+
+static int at803x_probe(struct phy_device *phydev)
+{
+	struct device *dev = &phydev->mdio.dev;
+	struct at803x_priv *priv;
+	int ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	/* Init LED polarity mode to -1 */
+	priv->led_polarity_mode = -1;
+
+	phydev->priv = priv;
+
+	ret = at803x_parse_dt(phydev);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int at803x_get_features(struct phy_device *phydev)
+{
+	struct at803x_priv *priv = phydev->priv;
+	int err;
+
+	err = genphy_read_abilities(phydev);
+	if (err)
+		return err;
+
+	if (phydev->drv->phy_id != ATH8031_PHY_ID)
+		return 0;
+
+	/* AR8031/AR8033 have different status registers
+	 * for copper and fiber operation. However, the
+	 * extended status register is the same for both
+	 * operation modes.
+	 *
+	 * As a result of that, ESTATUS_1000_XFULL is set
+	 * to 1 even when operating in copper TP mode.
+	 *
+	 * Remove this mode from the supported link modes
+	 * when not operating in 1000BaseX mode.
+	 */
+	if (!priv->is_1000basex)
+		linkmode_clear_bit(ETHTOOL_LINK_MODE_1000baseX_Full_BIT,
+				   phydev->supported);
+
+	return 0;
+}
+
+static int at803x_smarteee_config(struct phy_device *phydev)
+{
+	struct at803x_priv *priv = phydev->priv;
+	u16 mask = 0, val = 0;
+	int ret;
+
+	if (priv->flags & AT803X_DISABLE_SMARTEEE)
+		return phy_modify_mmd(phydev, MDIO_MMD_PCS,
+				      AT803X_MMD3_SMARTEEE_CTL3,
+				      AT803X_MMD3_SMARTEEE_CTL3_LPI_EN, 0);
+
+	if (priv->smarteee_lpi_tw_1g) {
+		mask |= 0xff00;
+		val |= priv->smarteee_lpi_tw_1g << 8;
+	}
+	if (priv->smarteee_lpi_tw_100m) {
+		mask |= 0x00ff;
+		val |= priv->smarteee_lpi_tw_100m;
+	}
+	if (!mask)
+		return 0;
+
+	ret = phy_modify_mmd(phydev, MDIO_MMD_PCS, AT803X_MMD3_SMARTEEE_CTL1,
+			     mask, val);
+	if (ret)
+		return ret;
+
+	return phy_modify_mmd(phydev, MDIO_MMD_PCS, AT803X_MMD3_SMARTEEE_CTL3,
+			      AT803X_MMD3_SMARTEEE_CTL3_LPI_EN,
+			      AT803X_MMD3_SMARTEEE_CTL3_LPI_EN);
+}
+
+static int at803x_clk_out_config(struct phy_device *phydev)
+{
+	struct at803x_priv *priv = phydev->priv;
+
+	if (!priv->clk_25m_mask)
+		return 0;
+
+	return phy_modify_mmd(phydev, MDIO_MMD_AN, AT803X_MMD7_CLK25M,
+			      priv->clk_25m_mask, priv->clk_25m_reg);
+}
+
+static int at8031_pll_config(struct phy_device *phydev)
+{
+	struct at803x_priv *priv = phydev->priv;
+
+	/* The default after hardware reset is PLL OFF. After a soft reset, the
+	 * values are retained.
+	 */
+	if (priv->flags & AT803X_KEEP_PLL_ENABLED)
+		return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F,
+					     0, AT803X_DEBUG_PLL_ON);
+	else
+		return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F,
+					     AT803X_DEBUG_PLL_ON, 0);
+}
+
+static int at803x_hibernation_mode_config(struct phy_device *phydev)
+{
+	struct at803x_priv *priv = phydev->priv;
+
+	/* The default after hardware reset is hibernation mode enabled. After
+	 * software reset, the value is retained.
+	 */
+	if (!(priv->flags & AT803X_DISABLE_HIBERNATION_MODE))
+		return 0;
+
+	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_HIB_CTRL,
+					 AT803X_DEBUG_HIB_CTRL_PS_HIB_EN, 0);
+}
+
+static int at803x_config_init(struct phy_device *phydev)
+{
+	int ret;
+
+	/* The RX and TX delay default is:
+	 *   after HW reset: RX delay enabled and TX delay disabled
+	 *   after SW reset: RX delay enabled, while TX delay retains the
+	 *   value before reset.
+	 */
+	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
+	    phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID)
+		ret = at803x_enable_rx_delay(phydev);
+	else
+		ret = at803x_disable_rx_delay(phydev);
+	if (ret < 0)
+		return ret;
+
+	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
+	    phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID)
+		ret = at803x_enable_tx_delay(phydev);
+	else
+		ret = at803x_disable_tx_delay(phydev);
+	if (ret < 0)
+		return ret;
+
+	ret = at803x_smarteee_config(phydev);
+	if (ret < 0)
+		return ret;
+
+	ret = at803x_clk_out_config(phydev);
+	if (ret < 0)
+		return ret;
+
+	ret = at803x_hibernation_mode_config(phydev);
+	if (ret < 0)
+		return ret;
+
+	/* Ar803x extended next page bit is enabled by default. Cisco
+	 * multigig switches read this bit and attempt to negotiate 10Gbps
+	 * rates even if the next page bit is disabled. This is incorrect
+	 * behaviour but we still need to accommodate it. XNP is only needed
+	 * for 10Gbps support, so disable XNP.
+	 */
+	return phy_modify(phydev, MII_ADVERTISE, MDIO_AN_CTRL1_XNP, 0);
+}
+
+static int at803x_ack_interrupt(struct phy_device *phydev)
+{
+	int err;
+
+	err = phy_read(phydev, AT803X_INTR_STATUS);
+
+	return (err < 0) ? err : 0;
+}
+
+static int at803x_config_intr(struct phy_device *phydev)
+{
+	int err;
+	int value;
+
+	value = phy_read(phydev, AT803X_INTR_ENABLE);
+
+	if (phydev->interrupts == PHY_INTERRUPT_ENABLED) {
+		/* Clear any pending interrupts */
+		err = at803x_ack_interrupt(phydev);
+		if (err)
+			return err;
+
+		value |= AT803X_INTR_ENABLE_AUTONEG_ERR;
+		value |= AT803X_INTR_ENABLE_SPEED_CHANGED;
+		value |= AT803X_INTR_ENABLE_DUPLEX_CHANGED;
+		value |= AT803X_INTR_ENABLE_LINK_FAIL;
+		value |= AT803X_INTR_ENABLE_LINK_SUCCESS;
+
+		err = phy_write(phydev, AT803X_INTR_ENABLE, value);
+	} else {
+		err = phy_write(phydev, AT803X_INTR_ENABLE, 0);
+		if (err)
+			return err;
+
+		/* Clear any pending interrupts */
+		err = at803x_ack_interrupt(phydev);
+	}
+
+	return err;
+}
+
+static irqreturn_t at803x_handle_interrupt(struct phy_device *phydev)
+{
+	int irq_status, int_enabled;
+
+	irq_status = phy_read(phydev, AT803X_INTR_STATUS);
+	if (irq_status < 0) {
+		phy_error(phydev);
+		return IRQ_NONE;
+	}
+
+	/* Read the current enabled interrupts */
+	int_enabled = phy_read(phydev, AT803X_INTR_ENABLE);
+	if (int_enabled < 0) {
+		phy_error(phydev);
+		return IRQ_NONE;
+	}
+
+	/* See if this was one of our enabled interrupts */
+	if (!(irq_status & int_enabled))
+		return IRQ_NONE;
+
+	phy_trigger_machine(phydev);
+
+	return IRQ_HANDLED;
+}
+
+static void at803x_link_change_notify(struct phy_device *phydev)
+{
+	/*
+	 * Conduct a hardware reset for AT8030 every time a link loss is
+	 * signalled. This is necessary to circumvent a hardware bug that
+	 * occurs when the cable is unplugged while TX packets are pending
+	 * in the FIFO. In such cases, the FIFO enters an error mode it
+	 * cannot recover from by software.
+	 */
+	if (phydev->state == PHY_NOLINK && phydev->mdio.reset_gpio) {
+		struct at803x_context context;
+
+		at803x_context_save(phydev, &context);
+
+		phy_device_reset(phydev, 1);
+		usleep_range(1000, 2000);
+		phy_device_reset(phydev, 0);
+		usleep_range(1000, 2000);
+
+		at803x_context_restore(phydev, &context);
+
+		phydev_dbg(phydev, "%s(): phy was reset\n", __func__);
+	}
+}
+
+static int at803x_read_specific_status(struct phy_device *phydev,
+				       struct at803x_ss_mask ss_mask)
+{
+	int ss;
+
+	/* Read the AT8035 PHY-Specific Status register, which indicates the
+	 * speed and duplex that the PHY is actually using, irrespective of
+	 * whether we are in autoneg mode or not.
+	 */
+	ss = phy_read(phydev, AT803X_SPECIFIC_STATUS);
+	if (ss < 0)
+		return ss;
+
+	if (ss & AT803X_SS_SPEED_DUPLEX_RESOLVED) {
+		int sfc, speed;
+
+		sfc = phy_read(phydev, AT803X_SPECIFIC_FUNCTION_CONTROL);
+		if (sfc < 0)
+			return sfc;
+
+		speed = ss & ss_mask.speed_mask;
+		speed >>= ss_mask.speed_shift;
+
+		switch (speed) {
+		case AT803X_SS_SPEED_10:
+			phydev->speed = SPEED_10;
+			break;
+		case AT803X_SS_SPEED_100:
+			phydev->speed = SPEED_100;
+			break;
+		case AT803X_SS_SPEED_1000:
+			phydev->speed = SPEED_1000;
+			break;
+		case QCA808X_SS_SPEED_2500:
+			phydev->speed = SPEED_2500;
+			break;
+		}
+		if (ss & AT803X_SS_DUPLEX)
+			phydev->duplex = DUPLEX_FULL;
+		else
+			phydev->duplex = DUPLEX_HALF;
+
+		if (ss & AT803X_SS_MDIX)
+			phydev->mdix = ETH_TP_MDI_X;
+		else
+			phydev->mdix = ETH_TP_MDI;
+
+		switch (FIELD_GET(AT803X_SFC_MDI_CROSSOVER_MODE_M, sfc)) {
+		case AT803X_SFC_MANUAL_MDI:
+			phydev->mdix_ctrl = ETH_TP_MDI;
+			break;
+		case AT803X_SFC_MANUAL_MDIX:
+			phydev->mdix_ctrl = ETH_TP_MDI_X;
+			break;
+		case AT803X_SFC_AUTOMATIC_CROSSOVER:
+			phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
+			break;
+		}
+	}
+
+	return 0;
+}
+
+static int at803x_read_status(struct phy_device *phydev)
+{
+	struct at803x_ss_mask ss_mask = { 0 };
+	int err, old_link = phydev->link;
+
+	/* Update the link, but return if there was an error */
+	err = genphy_update_link(phydev);
+	if (err)
+		return err;
+
+	/* why bother the PHY if nothing can have changed */
+	if (phydev->autoneg == AUTONEG_ENABLE && old_link && phydev->link)
+		return 0;
+
+	phydev->speed = SPEED_UNKNOWN;
+	phydev->duplex = DUPLEX_UNKNOWN;
+	phydev->pause = 0;
+	phydev->asym_pause = 0;
+
+	err = genphy_read_lpa(phydev);
+	if (err < 0)
+		return err;
+
+	ss_mask.speed_mask = AT803X_SS_SPEED_MASK;
+	ss_mask.speed_shift = __bf_shf(AT803X_SS_SPEED_MASK);
+	err = at803x_read_specific_status(phydev, ss_mask);
+	if (err < 0)
+		return err;
+
+	if (phydev->autoneg == AUTONEG_ENABLE && phydev->autoneg_complete)
+		phy_resolve_aneg_pause(phydev);
+
+	return 0;
+}
+
+static int at803x_config_mdix(struct phy_device *phydev, u8 ctrl)
+{
+	u16 val;
+
+	switch (ctrl) {
+	case ETH_TP_MDI:
+		val = AT803X_SFC_MANUAL_MDI;
+		break;
+	case ETH_TP_MDI_X:
+		val = AT803X_SFC_MANUAL_MDIX;
+		break;
+	case ETH_TP_MDI_AUTO:
+		val = AT803X_SFC_AUTOMATIC_CROSSOVER;
+		break;
+	default:
+		return 0;
+	}
+
+	return phy_modify_changed(phydev, AT803X_SPECIFIC_FUNCTION_CONTROL,
+			  AT803X_SFC_MDI_CROSSOVER_MODE_M,
+			  FIELD_PREP(AT803X_SFC_MDI_CROSSOVER_MODE_M, val));
+}
+
+static int at803x_prepare_config_aneg(struct phy_device *phydev)
+{
+	int ret;
+
+	ret = at803x_config_mdix(phydev, phydev->mdix_ctrl);
+	if (ret < 0)
+		return ret;
+
+	/* Changes of the midx bits are disruptive to the normal operation;
+	 * therefore any changes to these registers must be followed by a
+	 * software reset to take effect.
+	 */
+	if (ret == 1) {
+		ret = genphy_soft_reset(phydev);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int at803x_config_aneg(struct phy_device *phydev)
+{
+	struct at803x_priv *priv = phydev->priv;
+	int ret;
+
+	ret = at803x_prepare_config_aneg(phydev);
+	if (ret)
+		return ret;
+
+	if (priv->is_1000basex)
+		return genphy_c37_config_aneg(phydev);
+
+	return genphy_config_aneg(phydev);
+}
+
+static int at803x_get_downshift(struct phy_device *phydev, u8 *d)
+{
+	int val;
+
+	val = phy_read(phydev, AT803X_SMART_SPEED);
+	if (val < 0)
+		return val;
+
+	if (val & AT803X_SMART_SPEED_ENABLE)
+		*d = FIELD_GET(AT803X_SMART_SPEED_RETRY_LIMIT_MASK, val) + 2;
+	else
+		*d = DOWNSHIFT_DEV_DISABLE;
+
+	return 0;
+}
+
+static int at803x_set_downshift(struct phy_device *phydev, u8 cnt)
+{
+	u16 mask, set;
+	int ret;
+
+	switch (cnt) {
+	case DOWNSHIFT_DEV_DEFAULT_COUNT:
+		cnt = AT803X_DEFAULT_DOWNSHIFT;
+		fallthrough;
+	case AT803X_MIN_DOWNSHIFT ... AT803X_MAX_DOWNSHIFT:
+		set = AT803X_SMART_SPEED_ENABLE |
+		      AT803X_SMART_SPEED_BYPASS_TIMER |
+		      FIELD_PREP(AT803X_SMART_SPEED_RETRY_LIMIT_MASK, cnt - 2);
+		mask = AT803X_SMART_SPEED_RETRY_LIMIT_MASK;
+		break;
+	case DOWNSHIFT_DEV_DISABLE:
+		set = 0;
+		mask = AT803X_SMART_SPEED_ENABLE |
+		       AT803X_SMART_SPEED_BYPASS_TIMER;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	ret = phy_modify_changed(phydev, AT803X_SMART_SPEED, mask, set);
+
+	/* After changing the smart speed settings, we need to perform a
+	 * software reset, use phy_init_hw() to make sure we set the
+	 * reapply any values which might got lost during software reset.
+	 */
+	if (ret == 1)
+		ret = phy_init_hw(phydev);
+
+	return ret;
+}
+
+static int at803x_get_tunable(struct phy_device *phydev,
+			      struct ethtool_tunable *tuna, void *data)
+{
+	switch (tuna->id) {
+	case ETHTOOL_PHY_DOWNSHIFT:
+		return at803x_get_downshift(phydev, data);
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+static int at803x_set_tunable(struct phy_device *phydev,
+			      struct ethtool_tunable *tuna, const void *data)
+{
+	switch (tuna->id) {
+	case ETHTOOL_PHY_DOWNSHIFT:
+		return at803x_set_downshift(phydev, *(const u8 *)data);
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+static int at803x_cable_test_result_trans(u16 status)
+{
+	switch (FIELD_GET(AT803X_CDT_STATUS_STAT_MASK, status)) {
+	case AT803X_CDT_STATUS_STAT_NORMAL:
+		return ETHTOOL_A_CABLE_RESULT_CODE_OK;
+	case AT803X_CDT_STATUS_STAT_SHORT:
+		return ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT;
+	case AT803X_CDT_STATUS_STAT_OPEN:
+		return ETHTOOL_A_CABLE_RESULT_CODE_OPEN;
+	case AT803X_CDT_STATUS_STAT_FAIL:
+	default:
+		return ETHTOOL_A_CABLE_RESULT_CODE_UNSPEC;
+	}
+}
+
+static bool at803x_cdt_test_failed(u16 status)
+{
+	return FIELD_GET(AT803X_CDT_STATUS_STAT_MASK, status) ==
+		AT803X_CDT_STATUS_STAT_FAIL;
+}
+
+static bool at803x_cdt_fault_length_valid(u16 status)
+{
+	switch (FIELD_GET(AT803X_CDT_STATUS_STAT_MASK, status)) {
+	case AT803X_CDT_STATUS_STAT_OPEN:
+	case AT803X_CDT_STATUS_STAT_SHORT:
+		return true;
+	}
+	return false;
+}
+
+static int at803x_cdt_fault_length(int dt)
+{
+	/* According to the datasheet the distance to the fault is
+	 * DELTA_TIME * 0.824 meters.
+	 *
+	 * The author suspect the correct formula is:
+	 *
+	 *   fault_distance = DELTA_TIME * (c * VF) / 125MHz / 2
+	 *
+	 * where c is the speed of light, VF is the velocity factor of
+	 * the twisted pair cable, 125MHz the counter frequency and
+	 * we need to divide by 2 because the hardware will measure the
+	 * round trip time to the fault and back to the PHY.
+	 *
+	 * With a VF of 0.69 we get the factor 0.824 mentioned in the
+	 * datasheet.
+	 */
+	return (dt * 824) / 10;
+}
+
+static int at803x_cdt_start(struct phy_device *phydev,
+			    u32 cdt_start)
+{
+	return phy_write(phydev, AT803X_CDT, cdt_start);
+}
+
+static int at803x_cdt_wait_for_completion(struct phy_device *phydev,
+					  u32 cdt_en)
+{
+	int val, ret;
+
+	/* One test run takes about 25ms */
+	ret = phy_read_poll_timeout(phydev, AT803X_CDT, val,
+				    !(val & cdt_en),
+				    30000, 100000, true);
+
+	return ret < 0 ? ret : 0;
+}
+
+static int at803x_cable_test_one_pair(struct phy_device *phydev, int pair)
+{
+	static const int ethtool_pair[] = {
+		ETHTOOL_A_CABLE_PAIR_A,
+		ETHTOOL_A_CABLE_PAIR_B,
+		ETHTOOL_A_CABLE_PAIR_C,
+		ETHTOOL_A_CABLE_PAIR_D,
+	};
+	int ret, val;
+
+	val = FIELD_PREP(AT803X_CDT_MDI_PAIR_MASK, pair) |
+	      AT803X_CDT_ENABLE_TEST;
+	ret = at803x_cdt_start(phydev, val);
+	if (ret)
+		return ret;
+
+	ret = at803x_cdt_wait_for_completion(phydev, AT803X_CDT_ENABLE_TEST);
+	if (ret)
+		return ret;
+
+	val = phy_read(phydev, AT803X_CDT_STATUS);
+	if (val < 0)
+		return val;
+
+	if (at803x_cdt_test_failed(val))
+		return 0;
+
+	ethnl_cable_test_result(phydev, ethtool_pair[pair],
+				at803x_cable_test_result_trans(val));
+
+	if (at803x_cdt_fault_length_valid(val)) {
+		val = FIELD_GET(AT803X_CDT_STATUS_DELTA_TIME_MASK, val);
+		ethnl_cable_test_fault_length(phydev, ethtool_pair[pair],
+					      at803x_cdt_fault_length(val));
+	}
+
+	return 1;
+}
+
+static int at803x_cable_test_get_status(struct phy_device *phydev,
+					bool *finished, unsigned long pair_mask)
+{
+	int retries = 20;
+	int pair, ret;
+
+	*finished = false;
+
+	/* According to the datasheet the CDT can be performed when
+	 * there is no link partner or when the link partner is
+	 * auto-negotiating. Starting the test will restart the AN
+	 * automatically. It seems that doing this repeatedly we will
+	 * get a slot where our link partner won't disturb our
+	 * measurement.
+	 */
+	while (pair_mask && retries--) {
+		for_each_set_bit(pair, &pair_mask, 4) {
+			ret = at803x_cable_test_one_pair(phydev, pair);
+			if (ret < 0)
+				return ret;
+			if (ret)
+				clear_bit(pair, &pair_mask);
+		}
+		if (pair_mask)
+			msleep(250);
+	}
+
+	*finished = true;
+
+	return 0;
+}
+
+static void at803x_cable_test_autoneg(struct phy_device *phydev)
+{
+	/* Enable auto-negotiation, but advertise no capabilities, no link
+	 * will be established. A restart of the auto-negotiation is not
+	 * required, because the cable test will automatically break the link.
+	 */
+	phy_write(phydev, MII_BMCR, BMCR_ANENABLE);
+	phy_write(phydev, MII_ADVERTISE, ADVERTISE_CSMA);
+}
+
+static int at803x_cable_test_start(struct phy_device *phydev)
+{
+	at803x_cable_test_autoneg(phydev);
+	/* we do all the (time consuming) work later */
+	return 0;
+}
+
+static int at8031_rgmii_reg_set_voltage_sel(struct regulator_dev *rdev,
+					    unsigned int selector)
+{
+	struct phy_device *phydev = rdev_get_drvdata(rdev);
+
+	if (selector)
+		return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F,
+					     0, AT803X_DEBUG_RGMII_1V8);
+	else
+		return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F,
+					     AT803X_DEBUG_RGMII_1V8, 0);
+}
+
+static int at8031_rgmii_reg_get_voltage_sel(struct regulator_dev *rdev)
+{
+	struct phy_device *phydev = rdev_get_drvdata(rdev);
+	int val;
+
+	val = at803x_debug_reg_read(phydev, AT803X_DEBUG_REG_1F);
+	if (val < 0)
+		return val;
+
+	return (val & AT803X_DEBUG_RGMII_1V8) ? 1 : 0;
+}
+
+static const struct regulator_ops vddio_regulator_ops = {
+	.list_voltage = regulator_list_voltage_table,
+	.set_voltage_sel = at8031_rgmii_reg_set_voltage_sel,
+	.get_voltage_sel = at8031_rgmii_reg_get_voltage_sel,
+};
+
+static const unsigned int vddio_voltage_table[] = {
+	1500000,
+	1800000,
+};
+
+static const struct regulator_desc vddio_desc = {
+	.name = "vddio",
+	.of_match = of_match_ptr("vddio-regulator"),
+	.n_voltages = ARRAY_SIZE(vddio_voltage_table),
+	.volt_table = vddio_voltage_table,
+	.ops = &vddio_regulator_ops,
+	.type = REGULATOR_VOLTAGE,
+	.owner = THIS_MODULE,
+};
+
+static const struct regulator_ops vddh_regulator_ops = {
+};
+
+static const struct regulator_desc vddh_desc = {
+	.name = "vddh",
+	.of_match = of_match_ptr("vddh-regulator"),
+	.n_voltages = 1,
+	.fixed_uV = 2500000,
+	.ops = &vddh_regulator_ops,
+	.type = REGULATOR_VOLTAGE,
+	.owner = THIS_MODULE,
+};
+
+static int at8031_register_regulators(struct phy_device *phydev)
+{
+	struct at803x_priv *priv = phydev->priv;
+	struct device *dev = &phydev->mdio.dev;
+	struct regulator_config config = { };
+
+	config.dev = dev;
+	config.driver_data = phydev;
+
+	priv->vddio_rdev = devm_regulator_register(dev, &vddio_desc, &config);
+	if (IS_ERR(priv->vddio_rdev)) {
+		phydev_err(phydev, "failed to register VDDIO regulator\n");
+		return PTR_ERR(priv->vddio_rdev);
+	}
+
+	priv->vddh_rdev = devm_regulator_register(dev, &vddh_desc, &config);
+	if (IS_ERR(priv->vddh_rdev)) {
+		phydev_err(phydev, "failed to register VDDH regulator\n");
+		return PTR_ERR(priv->vddh_rdev);
+	}
+
+	return 0;
+}
+
+static int at8031_sfp_insert(void *upstream, const struct sfp_eeprom_id *id)
+{
+	struct phy_device *phydev = upstream;
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(phy_support);
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(sfp_support);
+	DECLARE_PHY_INTERFACE_MASK(interfaces);
+	phy_interface_t iface;
+
+	linkmode_zero(phy_support);
+	phylink_set(phy_support, 1000baseX_Full);
+	phylink_set(phy_support, 1000baseT_Full);
+	phylink_set(phy_support, Autoneg);
+	phylink_set(phy_support, Pause);
+	phylink_set(phy_support, Asym_Pause);
+
+	linkmode_zero(sfp_support);
+	sfp_parse_support(phydev->sfp_bus, id, sfp_support, interfaces);
+	/* Some modules support 10G modes as well as others we support.
+	 * Mask out non-supported modes so the correct interface is picked.
+	 */
+	linkmode_and(sfp_support, phy_support, sfp_support);
+
+	if (linkmode_empty(sfp_support)) {
+		dev_err(&phydev->mdio.dev, "incompatible SFP module inserted\n");
+		return -EINVAL;
+	}
+
+	iface = sfp_select_interface(phydev->sfp_bus, sfp_support);
+
+	/* Only 1000Base-X is supported by AR8031/8033 as the downstream SerDes
+	 * interface for use with SFP modules.
+	 * However, some copper modules detected as having a preferred SGMII
+	 * interface do default to and function in 1000Base-X mode, so just
+	 * print a warning and allow such modules, as they may have some chance
+	 * of working.
+	 */
+	if (iface == PHY_INTERFACE_MODE_SGMII)
+		dev_warn(&phydev->mdio.dev, "module may not function if 1000Base-X not supported\n");
+	else if (iface != PHY_INTERFACE_MODE_1000BASEX)
+		return -EINVAL;
+
+	return 0;
+}
+
+static const struct sfp_upstream_ops at8031_sfp_ops = {
+	.attach = phy_sfp_attach,
+	.detach = phy_sfp_detach,
+	.module_insert = at8031_sfp_insert,
+};
+
+static int at8031_parse_dt(struct phy_device *phydev)
+{
+	struct device_node *node = phydev->mdio.dev.of_node;
+	struct at803x_priv *priv = phydev->priv;
+	int ret;
+
+	if (of_property_read_bool(node, "qca,keep-pll-enabled"))
+		priv->flags |= AT803X_KEEP_PLL_ENABLED;
+
+	ret = at8031_register_regulators(phydev);
+	if (ret < 0)
+		return ret;
+
+	ret = devm_regulator_get_enable_optional(&phydev->mdio.dev,
+						 "vddio");
+	if (ret) {
+		phydev_err(phydev, "failed to get VDDIO regulator\n");
+		return ret;
+	}
+
+	/* Only AR8031/8033 support 1000Base-X for SFP modules */
+	return phy_sfp_probe(phydev, &at8031_sfp_ops);
+}
+
+static int at8031_probe(struct phy_device *phydev)
+{
+	struct at803x_priv *priv = phydev->priv;
+	int mode_cfg;
+	int ccr;
+	int ret;
+
+	ret = at803x_probe(phydev);
+	if (ret)
+		return ret;
+
+	/* Only supported on AR8031/AR8033, the AR8030/AR8035 use strapping
+	 * options.
+	 */
+	ret = at8031_parse_dt(phydev);
+	if (ret)
+		return ret;
+
+	ccr = phy_read(phydev, AT803X_REG_CHIP_CONFIG);
+	if (ccr < 0)
+		return ccr;
+	mode_cfg = ccr & AT803X_MODE_CFG_MASK;
+
+	switch (mode_cfg) {
+	case AT803X_MODE_CFG_BX1000_RGMII_50OHM:
+	case AT803X_MODE_CFG_BX1000_RGMII_75OHM:
+		priv->is_1000basex = true;
+		fallthrough;
+	case AT803X_MODE_CFG_FX100_RGMII_50OHM:
+	case AT803X_MODE_CFG_FX100_RGMII_75OHM:
+		priv->is_fiber = true;
+		break;
+	}
+
+	/* Disable WoL in 1588 register which is enabled
+	 * by default
+	 */
+	return phy_modify_mmd(phydev, MDIO_MMD_PCS,
+			      AT803X_PHY_MMD3_WOL_CTRL,
+			      AT803X_WOL_EN, 0);
+}
+
+static int at8031_config_init(struct phy_device *phydev)
+{
+	struct at803x_priv *priv = phydev->priv;
+	int ret;
+
+	/* Some bootloaders leave the fiber page selected.
+	 * Switch to the appropriate page (fiber or copper), as otherwise we
+	 * read the PHY capabilities from the wrong page.
+	 */
+	phy_lock_mdio_bus(phydev);
+	ret = at803x_write_page(phydev,
+				priv->is_fiber ? AT803X_PAGE_FIBER :
+						 AT803X_PAGE_COPPER);
+	phy_unlock_mdio_bus(phydev);
+	if (ret)
+		return ret;
+
+	ret = at8031_pll_config(phydev);
+	if (ret < 0)
+		return ret;
+
+	return at803x_config_init(phydev);
+}
+
+static int at8031_set_wol(struct phy_device *phydev,
+			  struct ethtool_wolinfo *wol)
+{
+	int ret;
+
+	/* First setup MAC address and enable WOL interrupt */
+	ret = at803x_set_wol(phydev, wol);
+	if (ret)
+		return ret;
+
+	if (wol->wolopts & WAKE_MAGIC)
+		/* Enable WOL function for 1588 */
+		ret = phy_modify_mmd(phydev, MDIO_MMD_PCS,
+				     AT803X_PHY_MMD3_WOL_CTRL,
+				     0, AT803X_WOL_EN);
+	else
+		/* Disable WoL function for 1588 */
+		ret = phy_modify_mmd(phydev, MDIO_MMD_PCS,
+				     AT803X_PHY_MMD3_WOL_CTRL,
+				     AT803X_WOL_EN, 0);
+
+	return ret;
+}
+
+static int at8031_config_intr(struct phy_device *phydev)
+{
+	struct at803x_priv *priv = phydev->priv;
+	int err, value = 0;
+
+	if (phydev->interrupts == PHY_INTERRUPT_ENABLED &&
+	    priv->is_fiber) {
+		/* Clear any pending interrupts */
+		err = at803x_ack_interrupt(phydev);
+		if (err)
+			return err;
+
+		value |= AT803X_INTR_ENABLE_LINK_FAIL_BX;
+		value |= AT803X_INTR_ENABLE_LINK_SUCCESS_BX;
+
+		err = phy_set_bits(phydev, AT803X_INTR_ENABLE, value);
+		if (err)
+			return err;
+	}
+
+	return at803x_config_intr(phydev);
+}
+
+/* AR8031 and AR8033 share the same read status logic */
+static int at8031_read_status(struct phy_device *phydev)
+{
+	struct at803x_priv *priv = phydev->priv;
+
+	if (priv->is_1000basex)
+		return genphy_c37_read_status(phydev);
+
+	return at803x_read_status(phydev);
+}
+
+/* AR8031 and AR8035 share the same cable test get status reg */
+static int at8031_cable_test_get_status(struct phy_device *phydev,
+					bool *finished)
+{
+	return at803x_cable_test_get_status(phydev, finished, 0xf);
+}
+
+/* AR8031 and AR8035 share the same cable test start logic */
+static int at8031_cable_test_start(struct phy_device *phydev)
+{
+	at803x_cable_test_autoneg(phydev);
+	phy_write(phydev, MII_CTRL1000, 0);
+	/* we do all the (time consuming) work later */
+	return 0;
+}
+
+/* AR8032, AR9331 and QCA9561 share the same cable test get status reg */
+static int at8032_cable_test_get_status(struct phy_device *phydev,
+					bool *finished)
+{
+	return at803x_cable_test_get_status(phydev, finished, 0x3);
+}
+
+static int at8035_parse_dt(struct phy_device *phydev)
+{
+	struct at803x_priv *priv = phydev->priv;
+
+	/* Mask is set by the generic at803x_parse_dt
+	 * if property is set. Assume property is set
+	 * with the mask not zero.
+	 */
+	if (priv->clk_25m_mask) {
+		/* Fixup for the AR8030/AR8035. This chip has another mask and
+		 * doesn't support the DSP reference. Eg. the lowest bit of the
+		 * mask. The upper two bits select the same frequencies. Mask
+		 * the lowest bit here.
+		 *
+		 * Warning:
+		 *   There was no datasheet for the AR8030 available so this is
+		 *   just a guess. But the AR8035 is listed as pin compatible
+		 *   to the AR8030 so there might be a good chance it works on
+		 *   the AR8030 too.
+		 */
+		priv->clk_25m_reg &= AT8035_CLK_OUT_MASK;
+		priv->clk_25m_mask &= AT8035_CLK_OUT_MASK;
+	}
+
+	return 0;
+}
+
+/* AR8030 and AR8035 shared the same special mask for clk_25m */
+static int at8035_probe(struct phy_device *phydev)
+{
+	int ret;
+
+	ret = at803x_probe(phydev);
+	if (ret)
+		return ret;
+
+	return at8035_parse_dt(phydev);
+}
+
+static int qca83xx_config_init(struct phy_device *phydev)
+{
+	u8 switch_revision;
+
+	switch_revision = phydev->dev_flags & QCA8K_DEVFLAGS_REVISION_MASK;
+
+	switch (switch_revision) {
+	case 1:
+		/* For 100M waveform */
+		at803x_debug_reg_write(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL, 0x02ea);
+		/* Turn on Gigabit clock */
+		at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_GREEN, 0x68a0);
+		break;
+
+	case 2:
+		phy_write_mmd(phydev, MDIO_MMD_AN, MDIO_AN_EEE_ADV, 0x0);
+		fallthrough;
+	case 4:
+		phy_write_mmd(phydev, MDIO_MMD_PCS, MDIO_AZ_DEBUG, 0x803f);
+		at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_GREEN, 0x6860);
+		at803x_debug_reg_write(phydev, AT803X_DEBUG_SYSTEM_CTRL_MODE, 0x2c46);
+		at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_3C, 0x6000);
+		break;
+	}
+
+	/* Following original QCA sourcecode set port to prefer master */
+	phy_set_bits(phydev, MII_CTRL1000, CTL1000_PREFER_MASTER);
+
+	return 0;
+}
+
+static int qca8327_config_init(struct phy_device *phydev)
+{
+	/* QCA8327 require DAC amplitude adjustment for 100m set to +6%.
+	 * Disable on init and enable only with 100m speed following
+	 * qca original source code.
+	 */
+	at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL,
+			      QCA8327_DEBUG_MANU_CTRL_EN, 0);
+
+	return qca83xx_config_init(phydev);
+}
+
+static void qca83xx_link_change_notify(struct phy_device *phydev)
+{
+	/* Set DAC Amplitude adjustment to +6% for 100m on link running */
+	if (phydev->state == PHY_RUNNING) {
+		if (phydev->speed == SPEED_100)
+			at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL,
+					      QCA8327_DEBUG_MANU_CTRL_EN,
+					      QCA8327_DEBUG_MANU_CTRL_EN);
+	} else {
+		/* Reset DAC Amplitude adjustment */
+		at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL,
+				      QCA8327_DEBUG_MANU_CTRL_EN, 0);
+	}
+}
+
+static int qca83xx_resume(struct phy_device *phydev)
+{
+	int ret, val;
+
+	/* Skip reset if not suspended */
+	if (!phydev->suspended)
+		return 0;
+
+	/* Reinit the port, reset values set by suspend */
+	qca83xx_config_init(phydev);
+
+	/* Reset the port on port resume */
+	phy_set_bits(phydev, MII_BMCR, BMCR_RESET | BMCR_ANENABLE);
+
+	/* On resume from suspend the switch execute a reset and
+	 * restart auto-negotiation. Wait for reset to complete.
+	 */
+	ret = phy_read_poll_timeout(phydev, MII_BMCR, val, !(val & BMCR_RESET),
+				    50000, 600000, true);
+	if (ret)
+		return ret;
+
+	usleep_range(1000, 2000);
+
+	return 0;
+}
+
+static int qca83xx_suspend(struct phy_device *phydev)
+{
+	at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_GREEN,
+			      AT803X_DEBUG_GATE_CLK_IN1000, 0);
+
+	at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_HIB_CTRL,
+			      AT803X_DEBUG_HIB_CTRL_EN_ANY_CHANGE |
+			      AT803X_DEBUG_HIB_CTRL_SEL_RST_80U, 0);
+
+	return 0;
+}
+
+static int qca8337_suspend(struct phy_device *phydev)
+{
+	/* Only QCA8337 support actual suspend. */
+	genphy_suspend(phydev);
+
+	return qca83xx_suspend(phydev);
+}
+
+static int qca8327_suspend(struct phy_device *phydev)
+{
+	u16 mask = 0;
+
+	/* QCA8327 cause port unreliability when phy suspend
+	 * is set.
+	 */
+	mask |= ~(BMCR_SPEED1000 | BMCR_FULLDPLX);
+	phy_modify(phydev, MII_BMCR, mask, 0);
+
+	return qca83xx_suspend(phydev);
+}
+
+static int qca808x_phy_fast_retrain_config(struct phy_device *phydev)
+{
+	int ret;
+
+	/* Enable fast retrain */
+	ret = genphy_c45_fast_retrain(phydev, true);
+	if (ret)
+		return ret;
+
+	phy_write_mmd(phydev, MDIO_MMD_AN, QCA808X_PHY_MMD7_TOP_OPTION1,
+		      QCA808X_TOP_OPTION1_DATA);
+	phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_20DB,
+		      QCA808X_MSE_THRESHOLD_20DB_VALUE);
+	phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_17DB,
+		      QCA808X_MSE_THRESHOLD_17DB_VALUE);
+	phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_27DB,
+		      QCA808X_MSE_THRESHOLD_27DB_VALUE);
+	phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_28DB,
+		      QCA808X_MSE_THRESHOLD_28DB_VALUE);
+	phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_1,
+		      QCA808X_MMD3_DEBUG_1_VALUE);
+	phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_4,
+		      QCA808X_MMD3_DEBUG_4_VALUE);
+	phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_5,
+		      QCA808X_MMD3_DEBUG_5_VALUE);
+	phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_3,
+		      QCA808X_MMD3_DEBUG_3_VALUE);
+	phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_6,
+		      QCA808X_MMD3_DEBUG_6_VALUE);
+	phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_2,
+		      QCA808X_MMD3_DEBUG_2_VALUE);
+
+	return 0;
+}
+
+static int qca808x_phy_ms_seed_enable(struct phy_device *phydev, bool enable)
+{
+	u16 seed_value;
+
+	if (!enable)
+		return at803x_debug_reg_mask(phydev, QCA808X_PHY_DEBUG_LOCAL_SEED,
+				QCA808X_MASTER_SLAVE_SEED_ENABLE, 0);
+
+	seed_value = get_random_u32_below(QCA808X_MASTER_SLAVE_SEED_RANGE);
+	return at803x_debug_reg_mask(phydev, QCA808X_PHY_DEBUG_LOCAL_SEED,
+			QCA808X_MASTER_SLAVE_SEED_CFG | QCA808X_MASTER_SLAVE_SEED_ENABLE,
+			FIELD_PREP(QCA808X_MASTER_SLAVE_SEED_CFG, seed_value) |
+			QCA808X_MASTER_SLAVE_SEED_ENABLE);
+}
+
+static bool qca808x_is_prefer_master(struct phy_device *phydev)
+{
+	return (phydev->master_slave_get == MASTER_SLAVE_CFG_MASTER_FORCE) ||
+		(phydev->master_slave_get == MASTER_SLAVE_CFG_MASTER_PREFERRED);
+}
+
+static bool qca808x_has_fast_retrain_or_slave_seed(struct phy_device *phydev)
+{
+	return linkmode_test_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->supported);
+}
+
+static int qca808x_config_init(struct phy_device *phydev)
+{
+	int ret;
+
+	/* Active adc&vga on 802.3az for the link 1000M and 100M */
+	ret = phy_modify_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_ADDR_CLD_CTRL7,
+			     QCA808X_8023AZ_AFE_CTRL_MASK, QCA808X_8023AZ_AFE_EN);
+	if (ret)
+		return ret;
+
+	/* Adjust the threshold on 802.3az for the link 1000M */
+	ret = phy_write_mmd(phydev, MDIO_MMD_PCS,
+			    QCA808X_PHY_MMD3_AZ_TRAINING_CTRL,
+			    QCA808X_MMD3_AZ_TRAINING_VAL);
+	if (ret)
+		return ret;
+
+	if (qca808x_has_fast_retrain_or_slave_seed(phydev)) {
+		/* Config the fast retrain for the link 2500M */
+		ret = qca808x_phy_fast_retrain_config(phydev);
+		if (ret)
+			return ret;
+
+		ret = genphy_read_master_slave(phydev);
+		if (ret < 0)
+			return ret;
+
+		if (!qca808x_is_prefer_master(phydev)) {
+			/* Enable seed and configure lower ramdom seed to make phy
+			 * linked as slave mode.
+			 */
+			ret = qca808x_phy_ms_seed_enable(phydev, true);
+			if (ret)
+				return ret;
+		}
+	}
+
+	/* Configure adc threshold as 100mv for the link 10M */
+	return at803x_debug_reg_mask(phydev, QCA808X_PHY_DEBUG_ADC_THRESHOLD,
+				     QCA808X_ADC_THRESHOLD_MASK,
+				     QCA808X_ADC_THRESHOLD_100MV);
+}
+
+static int qca808x_read_status(struct phy_device *phydev)
+{
+	struct at803x_ss_mask ss_mask = { 0 };
+	int ret;
+
+	ret = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_AN_10GBT_STAT);
+	if (ret < 0)
+		return ret;
+
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->lp_advertising,
+			 ret & MDIO_AN_10GBT_STAT_LP2_5G);
+
+	ret = genphy_read_status(phydev);
+	if (ret)
+		return ret;
+
+	/* qca8081 takes the different bits for speed value from at803x */
+	ss_mask.speed_mask = QCA808X_SS_SPEED_MASK;
+	ss_mask.speed_shift = __bf_shf(QCA808X_SS_SPEED_MASK);
+	ret = at803x_read_specific_status(phydev, ss_mask);
+	if (ret < 0)
+		return ret;
+
+	if (phydev->link) {
+		if (phydev->speed == SPEED_2500)
+			phydev->interface = PHY_INTERFACE_MODE_2500BASEX;
+		else
+			phydev->interface = PHY_INTERFACE_MODE_SGMII;
+	} else {
+		/* generate seed as a lower random value to make PHY linked as SLAVE easily,
+		 * except for master/slave configuration fault detected or the master mode
+		 * preferred.
+		 *
+		 * the reason for not putting this code into the function link_change_notify is
+		 * the corner case where the link partner is also the qca8081 PHY and the seed
+		 * value is configured as the same value, the link can't be up and no link change
+		 * occurs.
+		 */
+		if (qca808x_has_fast_retrain_or_slave_seed(phydev)) {
+			if (phydev->master_slave_state == MASTER_SLAVE_STATE_ERR ||
+			    qca808x_is_prefer_master(phydev)) {
+				qca808x_phy_ms_seed_enable(phydev, false);
+			} else {
+				qca808x_phy_ms_seed_enable(phydev, true);
+			}
+		}
+	}
+
+	return 0;
+}
+
+static int qca808x_soft_reset(struct phy_device *phydev)
+{
+	int ret;
+
+	ret = genphy_soft_reset(phydev);
+	if (ret < 0)
+		return ret;
+
+	if (qca808x_has_fast_retrain_or_slave_seed(phydev))
+		ret = qca808x_phy_ms_seed_enable(phydev, true);
+
+	return ret;
+}
+
+static bool qca808x_cdt_fault_length_valid(int cdt_code)
+{
+	switch (cdt_code) {
+	case QCA808X_CDT_STATUS_STAT_SAME_SHORT:
+	case QCA808X_CDT_STATUS_STAT_SAME_OPEN:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_NORMAL:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_OPEN:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_SHORT:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_NORMAL:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_OPEN:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_SHORT:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_NORMAL:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_OPEN:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_SHORT:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static int qca808x_cable_test_result_trans(int cdt_code)
+{
+	switch (cdt_code) {
+	case QCA808X_CDT_STATUS_STAT_NORMAL:
+		return ETHTOOL_A_CABLE_RESULT_CODE_OK;
+	case QCA808X_CDT_STATUS_STAT_SAME_SHORT:
+		return ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT;
+	case QCA808X_CDT_STATUS_STAT_SAME_OPEN:
+		return ETHTOOL_A_CABLE_RESULT_CODE_OPEN;
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_NORMAL:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_OPEN:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_SHORT:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_NORMAL:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_OPEN:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_SHORT:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_NORMAL:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_OPEN:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_SHORT:
+		return ETHTOOL_A_CABLE_RESULT_CODE_CROSS_SHORT;
+	case QCA808X_CDT_STATUS_STAT_FAIL:
+	default:
+		return ETHTOOL_A_CABLE_RESULT_CODE_UNSPEC;
+	}
+}
+
+static int qca808x_cdt_fault_length(struct phy_device *phydev, int pair,
+				    int result)
+{
+	int val;
+	u32 cdt_length_reg = 0;
+
+	switch (pair) {
+	case ETHTOOL_A_CABLE_PAIR_A:
+		cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_A;
+		break;
+	case ETHTOOL_A_CABLE_PAIR_B:
+		cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_B;
+		break;
+	case ETHTOOL_A_CABLE_PAIR_C:
+		cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_C;
+		break;
+	case ETHTOOL_A_CABLE_PAIR_D:
+		cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_D;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	val = phy_read_mmd(phydev, MDIO_MMD_PCS, cdt_length_reg);
+	if (val < 0)
+		return val;
+
+	if (result == ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT)
+		val = FIELD_GET(QCA808X_CDT_DIAG_LENGTH_SAME_SHORT, val);
+	else
+		val = FIELD_GET(QCA808X_CDT_DIAG_LENGTH_CROSS_SHORT, val);
+
+	return at803x_cdt_fault_length(val);
+}
+
+static int qca808x_cable_test_start(struct phy_device *phydev)
+{
+	int ret;
+
+	/* perform CDT with the following configs:
+	 * 1. disable hibernation.
+	 * 2. force PHY working in MDI mode.
+	 * 3. for PHY working in 1000BaseT.
+	 * 4. configure the threshold.
+	 */
+
+	ret = at803x_debug_reg_mask(phydev, QCA808X_DBG_AN_TEST, QCA808X_HIBERNATION_EN, 0);
+	if (ret < 0)
+		return ret;
+
+	ret = at803x_config_mdix(phydev, ETH_TP_MDI);
+	if (ret < 0)
+		return ret;
+
+	/* Force 1000base-T needs to configure PMA/PMD and MII_BMCR */
+	phydev->duplex = DUPLEX_FULL;
+	phydev->speed = SPEED_1000;
+	ret = genphy_c45_pma_setup_forced(phydev);
+	if (ret < 0)
+		return ret;
+
+	ret = genphy_setup_forced(phydev);
+	if (ret < 0)
+		return ret;
+
+	/* configure the thresholds for open, short, pair ok test */
+	phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8074, 0xc040);
+	phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8076, 0xc040);
+	phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8077, 0xa060);
+	phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8078, 0xc050);
+	phy_write_mmd(phydev, MDIO_MMD_PCS, 0x807a, 0xc060);
+	phy_write_mmd(phydev, MDIO_MMD_PCS, 0x807e, 0xb060);
+
+	return 0;
+}
+
+static int qca808x_cable_test_get_pair_status(struct phy_device *phydev, u8 pair,
+					      u16 status)
+{
+	int length, result;
+	u16 pair_code;
+
+	switch (pair) {
+	case ETHTOOL_A_CABLE_PAIR_A:
+		pair_code = FIELD_GET(QCA808X_CDT_CODE_PAIR_A, status);
+		break;
+	case ETHTOOL_A_CABLE_PAIR_B:
+		pair_code = FIELD_GET(QCA808X_CDT_CODE_PAIR_B, status);
+		break;
+	case ETHTOOL_A_CABLE_PAIR_C:
+		pair_code = FIELD_GET(QCA808X_CDT_CODE_PAIR_C, status);
+		break;
+	case ETHTOOL_A_CABLE_PAIR_D:
+		pair_code = FIELD_GET(QCA808X_CDT_CODE_PAIR_D, status);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	result = qca808x_cable_test_result_trans(pair_code);
+	ethnl_cable_test_result(phydev, pair, result);
+
+	if (qca808x_cdt_fault_length_valid(pair_code)) {
+		length = qca808x_cdt_fault_length(phydev, pair, result);
+		ethnl_cable_test_fault_length(phydev, pair, length);
+	}
+
+	return 0;
+}
+
+static int qca808x_cable_test_get_status(struct phy_device *phydev, bool *finished)
+{
+	int ret, val;
+
+	*finished = false;
+
+	val = QCA808X_CDT_ENABLE_TEST |
+	      QCA808X_CDT_LENGTH_UNIT;
+	ret = at803x_cdt_start(phydev, val);
+	if (ret)
+		return ret;
+
+	ret = at803x_cdt_wait_for_completion(phydev, QCA808X_CDT_ENABLE_TEST);
+	if (ret)
+		return ret;
+
+	val = phy_read_mmd(phydev, MDIO_MMD_PCS, QCA808X_MMD3_CDT_STATUS);
+	if (val < 0)
+		return val;
+
+	ret = qca808x_cable_test_get_pair_status(phydev, ETHTOOL_A_CABLE_PAIR_A, val);
+	if (ret)
+		return ret;
+
+	ret = qca808x_cable_test_get_pair_status(phydev, ETHTOOL_A_CABLE_PAIR_B, val);
+	if (ret)
+		return ret;
+
+	ret = qca808x_cable_test_get_pair_status(phydev, ETHTOOL_A_CABLE_PAIR_C, val);
+	if (ret)
+		return ret;
+
+	ret = qca808x_cable_test_get_pair_status(phydev, ETHTOOL_A_CABLE_PAIR_D, val);
+	if (ret)
+		return ret;
+
+	*finished = true;
+
+	return 0;
+}
+
+static int qca808x_get_features(struct phy_device *phydev)
+{
+	int ret;
+
+	ret = genphy_c45_pma_read_abilities(phydev);
+	if (ret)
+		return ret;
+
+	/* The autoneg ability is not existed in bit3 of MMD7.1,
+	 * but it is supported by qca808x PHY, so we add it here
+	 * manually.
+	 */
+	linkmode_set_bit(ETHTOOL_LINK_MODE_Autoneg_BIT, phydev->supported);
+
+	/* As for the qca8081 1G version chip, the 2500baseT ability is also
+	 * existed in the bit0 of MMD1.21, we need to remove it manually if
+	 * it is the qca8081 1G chip according to the bit0 of MMD7.0x901d.
+	 */
+	ret = phy_read_mmd(phydev, MDIO_MMD_AN, QCA808X_PHY_MMD7_CHIP_TYPE);
+	if (ret < 0)
+		return ret;
+
+	if (QCA808X_PHY_CHIP_TYPE_1G & ret)
+		linkmode_clear_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->supported);
+
+	return 0;
+}
+
+static int qca808x_config_aneg(struct phy_device *phydev)
+{
+	int phy_ctrl = 0;
+	int ret;
+
+	ret = at803x_prepare_config_aneg(phydev);
+	if (ret)
+		return ret;
+
+	/* The reg MII_BMCR also needs to be configured for force mode, the
+	 * genphy_config_aneg is also needed.
+	 */
+	if (phydev->autoneg == AUTONEG_DISABLE)
+		genphy_c45_pma_setup_forced(phydev);
+
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->advertising))
+		phy_ctrl = MDIO_AN_10GBT_CTRL_ADV2_5G;
+
+	ret = phy_modify_mmd_changed(phydev, MDIO_MMD_AN, MDIO_AN_10GBT_CTRL,
+				     MDIO_AN_10GBT_CTRL_ADV2_5G, phy_ctrl);
+	if (ret < 0)
+		return ret;
+
+	return __genphy_config_aneg(phydev, ret);
+}
+
+static void qca808x_link_change_notify(struct phy_device *phydev)
+{
+	/* Assert interface sgmii fifo on link down, deassert it on link up,
+	 * the interface device address is always phy address added by 1.
+	 */
+	mdiobus_c45_modify_changed(phydev->mdio.bus, phydev->mdio.addr + 1,
+				   MDIO_MMD_PMAPMD, QCA8081_PHY_SERDES_MMD1_FIFO_CTRL,
+				   QCA8081_PHY_FIFO_RSTN,
+				   phydev->link ? QCA8081_PHY_FIFO_RSTN : 0);
+}
+
+static int qca808x_led_parse_netdev(struct phy_device *phydev, unsigned long rules,
+				    u16 *offload_trigger)
+{
+	/* Parsing specific to netdev trigger */
+	if (test_bit(TRIGGER_NETDEV_TX, &rules))
+		*offload_trigger |= QCA808X_LED_TX_BLINK;
+	if (test_bit(TRIGGER_NETDEV_RX, &rules))
+		*offload_trigger |= QCA808X_LED_RX_BLINK;
+	if (test_bit(TRIGGER_NETDEV_LINK_10, &rules))
+		*offload_trigger |= QCA808X_LED_SPEED10_ON;
+	if (test_bit(TRIGGER_NETDEV_LINK_100, &rules))
+		*offload_trigger |= QCA808X_LED_SPEED100_ON;
+	if (test_bit(TRIGGER_NETDEV_LINK_1000, &rules))
+		*offload_trigger |= QCA808X_LED_SPEED1000_ON;
+	if (test_bit(TRIGGER_NETDEV_LINK_2500, &rules))
+		*offload_trigger |= QCA808X_LED_SPEED2500_ON;
+	if (test_bit(TRIGGER_NETDEV_HALF_DUPLEX, &rules))
+		*offload_trigger |= QCA808X_LED_HALF_DUPLEX_ON;
+	if (test_bit(TRIGGER_NETDEV_FULL_DUPLEX, &rules))
+		*offload_trigger |= QCA808X_LED_FULL_DUPLEX_ON;
+
+	if (rules && !*offload_trigger)
+		return -EOPNOTSUPP;
+
+	/* Enable BLINK_CHECK_BYPASS by default to make the LED
+	 * blink even with duplex or speed mode not enabled.
+	 */
+	*offload_trigger |= QCA808X_LED_BLINK_CHECK_BYPASS;
+
+	return 0;
+}
+
+static int qca808x_led_hw_control_enable(struct phy_device *phydev, u8 index)
+{
+	u16 reg;
+
+	if (index > 2)
+		return -EINVAL;
+
+	reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
+
+	return phy_clear_bits_mmd(phydev, MDIO_MMD_AN, reg,
+				  QCA808X_LED_FORCE_EN);
+}
+
+static int qca808x_led_hw_is_supported(struct phy_device *phydev, u8 index,
+				       unsigned long rules)
+{
+	u16 offload_trigger = 0;
+
+	if (index > 2)
+		return -EINVAL;
+
+	return qca808x_led_parse_netdev(phydev, rules, &offload_trigger);
+}
+
+static int qca808x_led_hw_control_set(struct phy_device *phydev, u8 index,
+				      unsigned long rules)
+{
+	u16 reg, offload_trigger = 0;
+	int ret;
+
+	if (index > 2)
+		return -EINVAL;
+
+	reg = QCA808X_MMD7_LED_CTRL(index);
+
+	ret = qca808x_led_parse_netdev(phydev, rules, &offload_trigger);
+	if (ret)
+		return ret;
+
+	ret = qca808x_led_hw_control_enable(phydev, index);
+	if (ret)
+		return ret;
+
+	return phy_modify_mmd(phydev, MDIO_MMD_AN, reg,
+			      QCA808X_LED_PATTERN_MASK,
+			      offload_trigger);
+}
+
+static bool qca808x_led_hw_control_status(struct phy_device *phydev, u8 index)
+{
+	u16 reg;
+	int val;
+
+	if (index > 2)
+		return false;
+
+	reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
+
+	val = phy_read_mmd(phydev, MDIO_MMD_AN, reg);
+
+	return !(val & QCA808X_LED_FORCE_EN);
+}
+
+static int qca808x_led_hw_control_get(struct phy_device *phydev, u8 index,
+				      unsigned long *rules)
+{
+	u16 reg;
+	int val;
+
+	if (index > 2)
+		return -EINVAL;
+
+	/* Check if we have hw control enabled */
+	if (qca808x_led_hw_control_status(phydev, index))
+		return -EINVAL;
+
+	reg = QCA808X_MMD7_LED_CTRL(index);
+
+	val = phy_read_mmd(phydev, MDIO_MMD_AN, reg);
+	if (val & QCA808X_LED_TX_BLINK)
+		set_bit(TRIGGER_NETDEV_TX, rules);
+	if (val & QCA808X_LED_RX_BLINK)
+		set_bit(TRIGGER_NETDEV_RX, rules);
+	if (val & QCA808X_LED_SPEED10_ON)
+		set_bit(TRIGGER_NETDEV_LINK_10, rules);
+	if (val & QCA808X_LED_SPEED100_ON)
+		set_bit(TRIGGER_NETDEV_LINK_100, rules);
+	if (val & QCA808X_LED_SPEED1000_ON)
+		set_bit(TRIGGER_NETDEV_LINK_1000, rules);
+	if (val & QCA808X_LED_SPEED2500_ON)
+		set_bit(TRIGGER_NETDEV_LINK_2500, rules);
+	if (val & QCA808X_LED_HALF_DUPLEX_ON)
+		set_bit(TRIGGER_NETDEV_HALF_DUPLEX, rules);
+	if (val & QCA808X_LED_FULL_DUPLEX_ON)
+		set_bit(TRIGGER_NETDEV_FULL_DUPLEX, rules);
+
+	return 0;
+}
+
+static int qca808x_led_hw_control_reset(struct phy_device *phydev, u8 index)
+{
+	u16 reg;
+
+	if (index > 2)
+		return -EINVAL;
+
+	reg = QCA808X_MMD7_LED_CTRL(index);
+
+	return phy_clear_bits_mmd(phydev, MDIO_MMD_AN, reg,
+				  QCA808X_LED_PATTERN_MASK);
+}
+
+static int qca808x_led_brightness_set(struct phy_device *phydev,
+				      u8 index, enum led_brightness value)
+{
+	u16 reg;
+	int ret;
+
+	if (index > 2)
+		return -EINVAL;
+
+	if (!value) {
+		ret = qca808x_led_hw_control_reset(phydev, index);
+		if (ret)
+			return ret;
+	}
+
+	reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
+
+	return phy_modify_mmd(phydev, MDIO_MMD_AN, reg,
+			      QCA808X_LED_FORCE_EN | QCA808X_LED_FORCE_MODE_MASK,
+			      QCA808X_LED_FORCE_EN | value ? QCA808X_LED_FORCE_ON :
+							     QCA808X_LED_FORCE_OFF);
+}
+
+static int qca808x_led_blink_set(struct phy_device *phydev, u8 index,
+				 unsigned long *delay_on,
+				 unsigned long *delay_off)
+{
+	int ret;
+	u16 reg;
+
+	if (index > 2)
+		return -EINVAL;
+
+	reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
+
+	/* Set blink to 50% off, 50% on at 4Hz by default */
+	ret = phy_modify_mmd(phydev, MDIO_MMD_AN, QCA808X_MMD7_LED_GLOBAL,
+			     QCA808X_LED_BLINK_FREQ_MASK | QCA808X_LED_BLINK_DUTY_MASK,
+			     QCA808X_LED_BLINK_FREQ_4HZ | QCA808X_LED_BLINK_DUTY_50_50);
+	if (ret)
+		return ret;
+
+	/* We use BLINK_1 for normal blinking */
+	ret = phy_modify_mmd(phydev, MDIO_MMD_AN, reg,
+			     QCA808X_LED_FORCE_EN | QCA808X_LED_FORCE_MODE_MASK,
+			     QCA808X_LED_FORCE_EN | QCA808X_LED_FORCE_BLINK_1);
+	if (ret)
+		return ret;
+
+	/* We set blink to 4Hz, aka 250ms */
+	*delay_on = 250 / 2;
+	*delay_off = 250 / 2;
+
+	return 0;
+}
+
+static int qca808x_led_polarity_set(struct phy_device *phydev, int index,
+				    unsigned long modes)
+{
+	struct at803x_priv *priv = phydev->priv;
+	bool active_low = false;
+	u32 mode;
+
+	for_each_set_bit(mode, &modes, __PHY_LED_MODES_NUM) {
+		switch (mode) {
+		case PHY_LED_ACTIVE_LOW:
+			active_low = true;
+			break;
+		default:
+			return -EINVAL;
+		}
+	}
+
+	/* PHY polarity is global and can't be set per LED.
+	 * To detect this, check if last requested polarity mode
+	 * match the new one.
+	 */
+	if (priv->led_polarity_mode >= 0 &&
+	    priv->led_polarity_mode != active_low) {
+		phydev_err(phydev, "PHY polarity is global. Mismatched polarity on different LED\n");
+		return -EINVAL;
+	}
+
+	/* Save the last PHY polarity mode */
+	priv->led_polarity_mode = active_low;
+
+	return phy_modify_mmd(phydev, MDIO_MMD_AN,
+			      QCA808X_MMD7_LED_POLARITY_CTRL,
+			      QCA808X_LED_ACTIVE_HIGH,
+			      active_low ? 0 : QCA808X_LED_ACTIVE_HIGH);
+}
+
+static struct phy_driver at803x_driver[] = {
+{
+	/* Qualcomm Atheros AR8035 */
+	PHY_ID_MATCH_EXACT(ATH8035_PHY_ID),
+	.name			= "Qualcomm Atheros AR8035",
+	.flags			= PHY_POLL_CABLE_TEST,
+	.probe			= at8035_probe,
+	.config_aneg		= at803x_config_aneg,
+	.config_init		= at803x_config_init,
+	.soft_reset		= genphy_soft_reset,
+	.set_wol		= at803x_set_wol,
+	.get_wol		= at803x_get_wol,
+	.suspend		= at803x_suspend,
+	.resume			= at803x_resume,
+	/* PHY_GBIT_FEATURES */
+	.read_status		= at803x_read_status,
+	.config_intr		= at803x_config_intr,
+	.handle_interrupt	= at803x_handle_interrupt,
+	.get_tunable		= at803x_get_tunable,
+	.set_tunable		= at803x_set_tunable,
+	.cable_test_start	= at8031_cable_test_start,
+	.cable_test_get_status	= at8031_cable_test_get_status,
+}, {
+	/* Qualcomm Atheros AR8030 */
+	.phy_id			= ATH8030_PHY_ID,
+	.name			= "Qualcomm Atheros AR8030",
+	.phy_id_mask		= AT8030_PHY_ID_MASK,
+	.probe			= at8035_probe,
+	.config_init		= at803x_config_init,
+	.link_change_notify	= at803x_link_change_notify,
+	.set_wol		= at803x_set_wol,
+	.get_wol		= at803x_get_wol,
+	.suspend		= at803x_suspend,
+	.resume			= at803x_resume,
+	/* PHY_BASIC_FEATURES */
+	.config_intr		= at803x_config_intr,
+	.handle_interrupt	= at803x_handle_interrupt,
+}, {
+	/* Qualcomm Atheros AR8031/AR8033 */
+	PHY_ID_MATCH_EXACT(ATH8031_PHY_ID),
+	.name			= "Qualcomm Atheros AR8031/AR8033",
+	.flags			= PHY_POLL_CABLE_TEST,
+	.probe			= at8031_probe,
+	.config_init		= at8031_config_init,
+	.config_aneg		= at803x_config_aneg,
+	.soft_reset		= genphy_soft_reset,
+	.set_wol		= at8031_set_wol,
+	.get_wol		= at803x_get_wol,
+	.suspend		= at803x_suspend,
+	.resume			= at803x_resume,
+	.read_page		= at803x_read_page,
+	.write_page		= at803x_write_page,
+	.get_features		= at803x_get_features,
+	.read_status		= at8031_read_status,
+	.config_intr		= at8031_config_intr,
+	.handle_interrupt	= at803x_handle_interrupt,
+	.get_tunable		= at803x_get_tunable,
+	.set_tunable		= at803x_set_tunable,
+	.cable_test_start	= at8031_cable_test_start,
+	.cable_test_get_status	= at8031_cable_test_get_status,
+}, {
+	/* Qualcomm Atheros AR8032 */
+	PHY_ID_MATCH_EXACT(ATH8032_PHY_ID),
+	.name			= "Qualcomm Atheros AR8032",
+	.probe			= at803x_probe,
+	.flags			= PHY_POLL_CABLE_TEST,
+	.config_init		= at803x_config_init,
+	.link_change_notify	= at803x_link_change_notify,
+	.suspend		= at803x_suspend,
+	.resume			= at803x_resume,
+	/* PHY_BASIC_FEATURES */
+	.config_intr		= at803x_config_intr,
+	.handle_interrupt	= at803x_handle_interrupt,
+	.cable_test_start	= at803x_cable_test_start,
+	.cable_test_get_status	= at8032_cable_test_get_status,
+}, {
+	/* ATHEROS AR9331 */
+	PHY_ID_MATCH_EXACT(ATH9331_PHY_ID),
+	.name			= "Qualcomm Atheros AR9331 built-in PHY",
+	.probe			= at803x_probe,
+	.suspend		= at803x_suspend,
+	.resume			= at803x_resume,
+	.flags			= PHY_POLL_CABLE_TEST,
+	/* PHY_BASIC_FEATURES */
+	.config_intr		= at803x_config_intr,
+	.handle_interrupt	= at803x_handle_interrupt,
+	.cable_test_start	= at803x_cable_test_start,
+	.cable_test_get_status	= at8032_cable_test_get_status,
+	.read_status		= at803x_read_status,
+	.soft_reset		= genphy_soft_reset,
+	.config_aneg		= at803x_config_aneg,
+}, {
+	/* Qualcomm Atheros QCA9561 */
+	PHY_ID_MATCH_EXACT(QCA9561_PHY_ID),
+	.name			= "Qualcomm Atheros QCA9561 built-in PHY",
+	.probe			= at803x_probe,
+	.suspend		= at803x_suspend,
+	.resume			= at803x_resume,
+	.flags			= PHY_POLL_CABLE_TEST,
+	/* PHY_BASIC_FEATURES */
+	.config_intr		= at803x_config_intr,
+	.handle_interrupt	= at803x_handle_interrupt,
+	.cable_test_start	= at803x_cable_test_start,
+	.cable_test_get_status	= at8032_cable_test_get_status,
+	.read_status		= at803x_read_status,
+	.soft_reset		= genphy_soft_reset,
+	.config_aneg		= at803x_config_aneg,
+}, {
+	/* QCA8337 */
+	.phy_id			= QCA8337_PHY_ID,
+	.phy_id_mask		= QCA8K_PHY_ID_MASK,
+	.name			= "Qualcomm Atheros 8337 internal PHY",
+	/* PHY_GBIT_FEATURES */
+	.probe			= at803x_probe,
+	.flags			= PHY_IS_INTERNAL,
+	.config_init		= qca83xx_config_init,
+	.soft_reset		= genphy_soft_reset,
+	.get_sset_count		= qca83xx_get_sset_count,
+	.get_strings		= qca83xx_get_strings,
+	.get_stats		= qca83xx_get_stats,
+	.suspend		= qca8337_suspend,
+	.resume			= qca83xx_resume,
+}, {
+	/* QCA8327-A from switch QCA8327-AL1A */
+	.phy_id			= QCA8327_A_PHY_ID,
+	.phy_id_mask		= QCA8K_PHY_ID_MASK,
+	.name			= "Qualcomm Atheros 8327-A internal PHY",
+	/* PHY_GBIT_FEATURES */
+	.link_change_notify	= qca83xx_link_change_notify,
+	.probe			= at803x_probe,
+	.flags			= PHY_IS_INTERNAL,
+	.config_init		= qca8327_config_init,
+	.soft_reset		= genphy_soft_reset,
+	.get_sset_count		= qca83xx_get_sset_count,
+	.get_strings		= qca83xx_get_strings,
+	.get_stats		= qca83xx_get_stats,
+	.suspend		= qca8327_suspend,
+	.resume			= qca83xx_resume,
+}, {
+	/* QCA8327-B from switch QCA8327-BL1A */
+	.phy_id			= QCA8327_B_PHY_ID,
+	.phy_id_mask		= QCA8K_PHY_ID_MASK,
+	.name			= "Qualcomm Atheros 8327-B internal PHY",
+	/* PHY_GBIT_FEATURES */
+	.link_change_notify	= qca83xx_link_change_notify,
+	.probe			= at803x_probe,
+	.flags			= PHY_IS_INTERNAL,
+	.config_init		= qca8327_config_init,
+	.soft_reset		= genphy_soft_reset,
+	.get_sset_count		= qca83xx_get_sset_count,
+	.get_strings		= qca83xx_get_strings,
+	.get_stats		= qca83xx_get_stats,
+	.suspend		= qca8327_suspend,
+	.resume			= qca83xx_resume,
+}, {
+	/* Qualcomm QCA8081 */
+	PHY_ID_MATCH_EXACT(QCA8081_PHY_ID),
+	.name			= "Qualcomm QCA8081",
+	.flags			= PHY_POLL_CABLE_TEST,
+	.probe			= at803x_probe,
+	.config_intr		= at803x_config_intr,
+	.handle_interrupt	= at803x_handle_interrupt,
+	.get_tunable		= at803x_get_tunable,
+	.set_tunable		= at803x_set_tunable,
+	.set_wol		= at803x_set_wol,
+	.get_wol		= at803x_get_wol,
+	.get_features		= qca808x_get_features,
+	.config_aneg		= qca808x_config_aneg,
+	.suspend		= genphy_suspend,
+	.resume			= genphy_resume,
+	.read_status		= qca808x_read_status,
+	.config_init		= qca808x_config_init,
+	.soft_reset		= qca808x_soft_reset,
+	.cable_test_start	= qca808x_cable_test_start,
+	.cable_test_get_status	= qca808x_cable_test_get_status,
+	.link_change_notify	= qca808x_link_change_notify,
+	.led_brightness_set	= qca808x_led_brightness_set,
+	.led_blink_set		= qca808x_led_blink_set,
+	.led_hw_is_supported	= qca808x_led_hw_is_supported,
+	.led_hw_control_set	= qca808x_led_hw_control_set,
+	.led_hw_control_get	= qca808x_led_hw_control_get,
+	.led_polarity_set	= qca808x_led_polarity_set,
+}, };
+
+module_phy_driver(at803x_driver);
+
+static struct mdio_device_id __maybe_unused atheros_tbl[] = {
+	{ ATH8030_PHY_ID, AT8030_PHY_ID_MASK },
+	{ PHY_ID_MATCH_EXACT(ATH8031_PHY_ID) },
+	{ PHY_ID_MATCH_EXACT(ATH8032_PHY_ID) },
+	{ PHY_ID_MATCH_EXACT(ATH8035_PHY_ID) },
+	{ PHY_ID_MATCH_EXACT(ATH9331_PHY_ID) },
+	{ PHY_ID_MATCH_EXACT(QCA8337_PHY_ID) },
+	{ PHY_ID_MATCH_EXACT(QCA8327_A_PHY_ID) },
+	{ PHY_ID_MATCH_EXACT(QCA8327_B_PHY_ID) },
+	{ PHY_ID_MATCH_EXACT(QCA9561_PHY_ID) },
+	{ PHY_ID_MATCH_EXACT(QCA8081_PHY_ID) },
+	{ }
+};
+
+MODULE_DEVICE_TABLE(mdio, atheros_tbl);