ipq40xx: Convert openmesh,a62 to DSA

* ethernet1:

  - physical port label "Ethernet 1"
  - can be used to power the device
  - its mac address is printed on the device label

* ethernet2:

  - physical port label "Ethernet 2"

Both ports are not marked by there role (because the vendor firmware
automatically detects roles) but the "Ethernet 1" port was used in the past
for "WAN" functionality in OpenWrt.

Reviewed-by: Robert Marko <[email protected]>
Tested-by: Michaël BILCOT <[email protected]>
Signed-off-by: Sven Eckelmann <[email protected]>

target/linux/ipq40xx/base-files/etc/board.d/02_network

@@ -73,7 +73,8 @@ ipq40xx_setup_interfaces()
 	netgear,srs60)
 		ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "wan"
 		;;
-	openmesh,a42)
+	openmesh,a42|\
+	openmesh,a62)
 		ucidef_set_interfaces_lan_wan "ethernet2" "ethernet1"
 		;;
 	zte,mf286d)
@@ -162,7 +163,8 @@ ipq40xx_setup_macs()
 	pakedge,wr-1)
 		wan_mac=$(macaddr_add $(get_mac_label) 1)
 		;;
-	openmesh,a42)
+	openmesh,a42|\
+	openmesh,a62)
 		label_mac="$(mtd_get_mac_binary "0:ART" 0x0)"
 		;;
 	esac

target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh

@@ -29,7 +29,8 @@ preinit_set_mac_address() {
 		ip link set dev lan1 address $(macaddr_add "$base_mac" 1)
 		ip link set dev eth0 address $(macaddr_setbit "$base_mac" 7)
 		;;
-	openmesh,a42)
+	openmesh,a42|\
+	openmesh,a62)
 		ip link set dev ethernet1 address $(mtd_get_mac_binary "0:ART" 0x0)
 		ip link set dev ethernet2 address $(mtd_get_mac_binary "0:ART" 0x6)
 		;;

target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-a62.dts

@@ -17,10 +17,6 @@
 			status = "okay";
 		};
 
-		mdio@90000 {
-			status = "okay";
-		};
-
 		tcsr@194b000 {
 			/* select hostmode */
 			compatible = "qcom,tcsr";
@@ -194,6 +190,28 @@
 	};
 };
 
+&mdio {
+	status = "okay";
+};
+
+&gmac {
+	status = "okay";
+};
+
+&switch {
+	status = "okay";
+};
+
+&swport4 {
+	status = "okay";
+	label = "ethernet1";
+};
+
+&swport5 {
+	status = "okay";
+	label = "ethernet2";
+};
+
 &wifi0 {
 	status = "okay";
 	qcom,ath10k-calibration-variant = "OM-A62";

target/linux/ipq40xx/image/generic.mk

@@ -904,8 +904,7 @@ define Device/openmesh_a62
 	IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
 	DEVICE_PACKAGES := ath10k-firmware-qca9888-ct
 endef
-# Missing DSA Setup
-#TARGET_DEVICES += openmesh_a62
+TARGET_DEVICES += openmesh_a62
 
 define Device/p2w_r619ac
 	$(call Device/FitzImage)